Resumen del contenido incluido en la página 1
English
Univ Univ Universal F ersal F ersal Fan and an and an and
Light Remot Light Remote Contr e Control ol
Light Remote Control
Hand-Held Remote and Wall Cradle
Owner’s Guide and
Installation Manual
Models 27184, 27188
Form# 41797-01
20100706
©2010 Hunter Fan Co.
Resumen del contenido incluido en la página 2
1 • Welcome Read and Save these Instructions Table of Contents Caution: Risk of Electrical Shock! All wiring must be performed in accordance with 1 • Welcome ..............................................................2 national and local electrical codes. If you are unfamiliar with the wiring codes, you should use a 2 • Installation Preparation ...............................3 qualified electrician. 3 • DIP Switch Settings ........................................4 To avoid overheating an
Resumen del contenido incluido en la página 3
2 • Installation Preparation and fan incandescent light kits rated at 300 watts or less. Notes: 1. This device complies with Part 15 of the FCC Rules. Operation is subject 4. Not for use with shaded-pole motors, Hunter 42” Low Profile fans, and to the following two conditions: (1) this device may not cause harmful Hunter Baseball fans. Not recommended for use with the Hunter Original®. interference, and (2) this device must accept any interference received, For Hunter Original® series fans,
Resumen del contenido incluido en la página 4
3 • Setting Jumpers & DIP Switches BEFORE INSTALLING THE CONTROL: 1. Use the pull chain switch to set the fan speed to the HIGH position before installation. Example Settings Do not use the pull chain to change the fan speed after installation, as damage to Transmitter Receiver your ceiling fan or universal control may result. The speed of the fan should only be changed by the Hunter control. 4 3 2 1 2. Set the ceiling fan light kit to the ON position before installation. The light level sho
Resumen del contenido incluido en la página 5
4 • Receiver Installation 4. Install the ceiling fan according to its instructions, up to the point of making the electrical connections. Connect receiver to ceiling fan according to the mounting types shown on the next page. Determine your ceiling fan mounting type from the images on Pages 5-6. Most installations will be one of these Antenna five types. 5. If the fan is already installed, turn the power OFF at the main electrical panel. Reverse the installation procedure according to the
Resumen del contenido incluido en la página 6
4 • Receiver Installation NOTE: Some fans may have considerable excess lead wire. For easier canopy installation, cut the excess wire leaving a minimum of 6 inches remaining. Restrip the fan lead wires 1/2 inch. Place remaining excess wire into the ceiling electrical box as needed. Hunter Hands-Free™ Canopy: Connect wiring as shown in Figure 7. Place receiver inside mounting Figure 8 bracket. Extend antenna above the ceiling mounting bracket Hands Bracket (approximately 3–6˝). Free Ha
Resumen del contenido incluido en la página 7
4 • Receiver Installation 6. Use the 2 large (orange) wire connectors supplied to connect Figure 9 the receiver and house wiring, then use the 3 small (blue) wire connectors supplied to connect the receiver and ceiling fan Antenna wiring. Refer to the Wiring Diagram in Figure 9. 7. Be sure the antenna is positioned securely, so it can not Black/Hot (marked “LIVE interfere with the ceiling fan motor. Refer to Figure 9. Do not IN on red label) modify or damage the antenna wire, as control p
Resumen del contenido incluido en la página 8
5 • Transmitter Installation 1. Install the 12 Volt alkaline battery (A23 or equivalent) inside the handheld transmitter, after setting the jumpers to match the dip switches in the receiver. Refer to Figure 11. 2 Mount the remote holder over the ceiling fan’s wall switch using the existing wall plate screws. Refer to Figure 12. 3. The transmitter can be placed on the remote holder for convenience or safekeeping. Select your own unique code, making sure the settings match in the transmitter an
Resumen del contenido incluido en la página 9
6 • Operation Light Operation: • Turn ON wall switch. The light will turn ON at maximum brightness. Reversing • Press and quickly release either light button on the hand held remote to turn the light OFF or ON. Switch The light will come ON at maximum brightness. • After a power outage, the light will turn ON when power is restored. Press and quickly release one of the light buttons once to turn the light back off after a power outage. • Press and hold either light button for more than 1
Resumen del contenido incluido en la página 10
7 • Troubleshooting Symptom Possible Causes Solution 1.No functions operate. Main Power not restored. Replace fuse. Turn ON circuit breaker. Turn ON wall switch. Fan pull chain not set to High. Set fan pull chain to High speed. Light pull chain not set to ON. Set light kit to ON. Receiver wiring incorrect. Verify wiring connections. Transmitter and receiver DIP Set transmitter and receiver to same DIP switch setting. switches do not match. Battery too weak. Replace with new, 12 Volt alkaline
Resumen del contenido incluido en la página 11
8 • Warranty HUNTER FAN COMPANY CONTROL LIMITED WARRANTY The Hunter Fan Company makes the following limited warranty to the original purchaser of the Control (“Control”): Your Control is warranted to be free from defects in material and workmanship for a period of one year from the date of sale. If the Control malfunctions or fails within the warranty period due to a defect in material or workmanship we will replace it free of charge. IF THE ORIGINAL PURCHASER CEASES TO OWN THE CONTROL, THI
