Manual de instrucciones de Pelco HKHS3024

Resumen del contenido incluido en la página 1

INSTALLATION
HKHS3000/HKHS3024
Heater Kits
C499M-A (11/05)

Resumen del contenido incluido en la página 2

Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Do not use this apparatus near water. 5. Only use attachments/accessories specified by the manufacturer. 6. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 7. Refer all servicing to qualified service personnel

Resumen del contenido incluido en la página 3

Description The HKHS3000 (120 VAC) and HKHS3024 (24 VAC) are field installed heater kits for the HS3000 and HS3020 high security enclosures. These heater kits provide 30 watts of heat and are thermostatically controlled ON at 40°F (4.44°C) and OFF at 60°F (15.56°C). RECOMMENDED CABLE DISTANCES The following are the recommended cable distances for heater operation when used with a transformer capable of delivering the power require- ments. Cable distances are based on a 10% line loss. 120

Resumen del contenido incluido en la página 4

Installation To install the HKHS3000 and HKHS3024, perform the following steps: 1. Remove the cover from the enclosure. 2. Attach the PC board/bracket assembly to the studs on the rear end plate (refer to Figure 1 and Figure 3) using the two 1/4-20 nuts supplied. 3. Install the heater pads onto the front of the body (end nearest window) by removing the backing and pressing in place onto the floor of enclosure (refer to Figure 3). 4. Wire per wiring diagram in Figure 2. Figure 1. Heathe

Resumen del contenido incluido en la página 5

Exploded Assembly Diagram Figure 3. HKHS3000/HKHS3024 Exploded Assembly Diagram The following parts list corresponds to the items identified in Figure 3 above. Table A. Mechanical Parts List Item Number Quantity Description Part Number 1 2 Heater Blanket, 120 VAC, 15 watts (HKHS3000) HK300010115 Heather Blanket, 24 VAC, 15 watts (HKHS3024) HK300010024 2 1 Bracket, PCB HSK30004000COMP 3 1 PCB aseembly, term/thermostat PCB900300ASSY A 2 Nut, hex 1/40-20 ZH1/4-20NUTCH B 2 Washer, #5610-22-

Resumen del contenido incluido en la página 6

6 C499M-A (11/05)

Resumen del contenido incluido en la página 7

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or workmanship for a period of one year after the date of shipment. (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information: Exceptions to this warranty are as noted below: 1. Model and serial num

Resumen del contenido incluido en la página 8

Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO9001 United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East | | | | | | | |