Resumen del contenido incluido en la página 1
ETA-ECS3
Power Sequencer & Conditioner
ETA-ECS3
Power Sequencer & Conditioner
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800-321-6699 • Fax: 800-996-3821
– 1 – ETAsys.com
Specifications are subject to change without notice.
Resumen del contenido incluido en la página 2
ETA-ECS3 Power Sequencer & Conditioner TABLE OF CONTENTS Important Safety Instructions ................................................................................................................. 3 Introduction ........................................................................................................................................... 5 Key Features ...........................................................................................................................
Resumen del contenido incluido en la página 3
ETA-ECS3 Power Sequencer & Conditioner IMPORTANT SAFETY INSTRUCTIONS The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage “ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) inst
Resumen del contenido incluido en la página 4
ETA-ECS3 Power Sequencer & Conditioner WARNING – WHEN THE DEVICE IS IN USE • T o prevent electric shock, do not remove the product cover as there are high voltage components inside. Refer all servicing to ETA Systems. • Should any of the following irregularities occur during use, immediately switch off the power , disconnect the power cord from the AC outlet and contact ETA Systems. Do not to attempt to continue operation with the product as this may cause fire or electric shock:
Resumen del contenido incluido en la página 5
ETA-ECS3 Power Sequencer & Conditioner INTRODUCTION Thank you for purchasing the ETA Systems ETA-ECS3 AC Power Sequencer and Conditioner. The ETA-ECS3 has been designed to meet most installation requirements for AC power distribution and equipment power protection. The 15A compact 1RU unit features three sequential timing sections that can be activated via the unit, or remotely. Front panel activation is via a momentary switch, while rear activation is via a momentary contact closure, or by
Resumen del contenido incluido en la página 6
ETA-ECS3 Power Sequencer & Conditioner KEY FEATURES • 3 Sequencer T iming Sections Fixed 3-Second Intervals, 6 Seconds T otal • 9 T otal Outlets Are Provided • 6 Rear Panel Outlets Are Sequenced In Three Steps • 2 Front Panel and 1 Rear Panel Unswitched Convenience Outlets • RFI Noise Filtering to Reduce Radio Frequency Interference • EMI T o Reduce Electromagnetic Interference • Dual Clamping Spike & Surge Supp
Resumen del contenido incluido en la página 7
ETA-ECS3 Power Sequencer & Conditioner FRONT PANEL FEATURES 1 2 3 4 5 1. Unswitched AC Outlet – The two 120V AC outlets are always live when the ETA-ECS3 power cord is plugged into an AC mains power source and voltage is present. If voltage is present at the outlets, it will be displayed on the AC Mains Meter. Note: The AC mains power switch or sequencer section does not affect the Unswitched AC Outlets. The Unswitched Outlets are protected by the surge protection circuitry, but will not b
Resumen del contenido incluido en la página 8
ETA-ECS3 Power Sequencer & Conditioner 6. AC Mains Function Display 7. AC Mains Voltage Display – This display will illuminate when 8 9 10 11 12 the AC Mains power cord is plugged into an AC source. Note: the display has a 1.5% tolerance. Note: If the voltage displayed is not between 107 - 128VAC, refer to the troubleshooting section and item 12 below. 8. Sequence Indicator – There are three green LED active sequence outlet indicators labeled “SEQ 1”, “S
Resumen del contenido incluido en la página 9
ETA-ECS3 Power Sequencer & Conditioner REAR PANEL FEATURES 6 5 2 3 4 7 1 1. AC Mains Input – Connect the 9’ (3m) power cord to a 15A 120VAC outlet to provide power to the ETA-ECS3. 2. Sequence 1 AC Outlets – The three AC outlets are “Live” when the Sequence 1 section is activated. These outlets are recommended for products such as Computers, Modems, Routers, DSP Processors, Cable/SAT, DVD, or CRT TV’s. These outlets have a special filter circuit that is optimized to redu
Resumen del contenido incluido en la página 10
ETA-ECS3 Power Sequencer & Conditioner INSTALLATION Before installing we strongly suggest you read the entire manual to ensure you benefit from all the features of the ET A-ECS3. The ETA-ECS3 can be placed on a shelf or rack mounted in a standard 19" width rack. Placement within a rack is not critical but the rack should be within 6' of dedicated 15A AC outlet. Always make sure the 15A outlet is properly inspected by a certified electrician prior t
Resumen del contenido incluido en la página 11
ETA-ECS3 Power Sequencer & Conditioner AC POWER CORD RETAINER SYSTEM Your ETA Systems product comes with an AC Mains Power Cord Retainer System. This system prevents the power cord from being removed without the use of a screwdriver. Follow these steps for installation. Note: Installation of this product must be done by a certified electrician for a permanently connected apparatus provided neither with an all-pole mains switch nor an all-pole circuit breaker. A readily accessible disconnect d
Resumen del contenido incluido en la página 12
ETA-ECS3 Power Sequencer & Conditioner SPECIFICATIONS T ype Power Sequencer , Power Conditioner & Suppressor Sequencer Sections 3, Fixed T ime of 3 Seconds Between “On” Seq. 2 & 3, “Off” 2 & 1 Load Rating 15A Continuous Safety Listing ETL (UL 60065 Standard) Front Panel AC Outlets 2 Unswitched Lights 1 Pull out LED with Dimmer Switch Activation Switch Momentary Circuit Breaker 15A Resettable AC Mains Voltmeter Three Digits (Digital) Indicators Sequencer Sections 1,
Resumen del contenido incluido en la página 13
ETA-ECS3 Power Sequencer & Conditioner NOTES: 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800-321-6699 • Fax: 800-996-3821 – 13 – ETAsys.com Specifications are subject to change without notice.
Resumen del contenido incluido en la página 14
ETA-ECS3 Power Sequencer & Conditioner NOTES: 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800-321-6699 • Fax: 800-996-3821 – 14 – ETAsys.com Specifications are subject to change without notice.
Resumen del contenido incluido en la página 15
ETA-ECS3 Power Sequencer & Conditioner NOTES: 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800-321-6699 • Fax: 800-996-3821 – 15 – ETAsys.com Specifications are subject to change without notice.
Resumen del contenido incluido en la página 16
ETA-ECS3 Power Sequencer & Conditioner LIMITED WARRANTY All products manufactured by ETA Systems are warranted to the original dealer/installer, industrial or commercial purchaser to be free from defects in material and workmanship and to be in compliance with our published specifications, if any. This warranty shall extend from the date of purchase for a period of one year. Additionally, fuses and lamps carry no warranty. ETA Systems will solely at its discretion, replace at no charge or re
