Resumen del contenido incluido en la página 1
&OPERATOR’S MANUAL
BCIOOO BAGGER CART
I I I I I I I I I I I I I I I I I I I I
+-I HONDA DEALER: PLEASE GIVE THIS PUBLICATION TO YOUR CUSTOMERl-+-
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
-- A FEW WORDS ABOUT SAFETY TABLE OF CONTENTS SAFETY ...................................................... Your safety and the safety of others are very important. SAFETY LABELS.. ....................................... And using this bagger cart is an important responsibility. CONTROLS ................................................ To help you make informed decisions about safety, we CONTROLS ................................................ : have provided operating procedures and
Resumen del contenido incluido en la página 4
SAFETY SAFETY LABELS The label shown here contains important safety information. Please read it carefully. This label is considered a permanent part of your side blower. If the label comes off or becomes hard to read, immediately contact an authorized Honda servicing dealer for a replacement label. OBJECTS MAY BE THROWN FROM MOWER. n DO NOT OPERATE MOWER UNLESS r GRASS CATCHER IS ATTACHED. BClOOO BAGGER CART 2 A
Resumen del contenido incluido en la página 5
CONTROLS CONTROLS This chapter shows the bagger cart control locations and it tells you how the bagger controls work. It only covers controls relating to the bagger cart. Have your Honda tractor owner’s manual handy for reference while reading this chapter. Rubber Strap This rubber strap holds the cover open or closed. The strap connects to the frame washer to hold the cover FRAME closed, or the grommet strap to hold it open. WASHER RUBBER STRAP GROMMET STRAP Dump Cloth DUMP CLOT
Resumen del contenido incluido en la página 6
BEFORE OPERATION For your safety, and to prolong the service life of your equipment, always inspect the bagger cart before each use. Refer to the MAINTENANCE SCHEDULE on page 12. Perform the Before Operation checks listed in the tractor’s manual. CHECK MOWING AREA For your safety and the safety of others, always inspect the area before mowing. Objects Anything which can be picked up by the mower deck is a potential hazard to you and others. Always remove any large debris from the mowing
Resumen del contenido incluido en la página 7
IMPORTANT SAFETY INFORMATION IMPORTANT SAFETY INFORMATION Before operating the lawn tractor with the bagger cart installed for the first time, please review the safety information in the lawn tractor owner’s manual, and the previous chapter of this book, BEFORE OPERATION. For your safety, avoid starting or operating the tractor’s engine in an enclosed area such as a garage, Your tractor’s engine exhaust contains poisonous carbon monoxide gas which can collect rapidly in an enclosed area a
Resumen del contenido incluido en la página 8
OPERATION CONNECTING THE BAGGER CART Park the tractor on a flat, level surface. Set the parking CLEVIS PI brake and remove the ignition key to prevent accidental starting. The following instructions are for the HA411 8 and HA4120 tractors only. Refer to the hitch kit installation instructions for other tractor models. 1, Lift the bagger cart frame towards therear hitch. Install the two clevis pins and spring clips as shown. SPRING CLIP (2) ’ \ 2. HA4120 with the 48” Deck: Lift the mi
Resumen del contenido incluido en la página 9
OPERATION STARTING AND STOPPING The bagger cart adds weight (especially when filled) that can change the way the tractor handles. Operate the tractor at a slower speed when using the bagger cart. This will make the tractor and bagger cart easier to operate and control. Start in a lower gear (or speed) and plan stops further in advance when using the bagger cart. MOWING The bagger cart holds a large amount of clippings that can change the way the tractor handles. The bagger cart works bes
Resumen del contenido incluido en la página 10
OPERATION Emptying the Bagger Cart Use the inspection window in the top cover to check the clipping level. When you see grass collecting at the window level, the cart must be emptied. Make sure the PTO clutch lever/knob is OFF. Back the tractor up to the location where you want to empty the clippings. Stop the tractor, set the parking brake ON, and remove the ignition key. Unhook the rubber strap from the cover on the rear of the bagger cart. Pull the cover over the top of the frame, and
Resumen del contenido incluido en la página 11
OPERATION TIPPING THE CART BED: RELEASE LOCK 1. Disconnect the middle chute (with the inspection window) from the lower chute. LATCH HANDLE 2. Move the latch handle down to unlock the bagger cart bed. LIFT Grasp one of the lift handles, then tip the cart bed to dump HANDLE the clippings. USE AS A UTILITY CART The bagger cart can also serve as a light-duty utility cart for your tractor. For many applications, all you need do is roll up the cover and fasten it to the grommet strap (pag
Resumen del contenido incluido en la página 12
MAINTENANCE THE IMPORTANCE OF MAINTENANCE Good maintenance is essential for safe, economical, and trouble-free operation. Improper maintenance, or failure to correct a problem before operation, can cause a malfunction in which you can be seriously hurt or killed. Always follow the inspection and maintenance recommendations and schedules in this operator’s manual and the owner’s manual included with the tractor. To help you properly care for your bagger cart, the following pages include
Resumen del contenido incluido en la página 13
MAINTENANCE MAINTENANCE SAFETY Some of the most important safety precautions follow. However, we cannot warn you of every conceivable. hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task. precautions can cause you to be seriously hurt or killed Always follow the procedures and precautions in this operator’s manual and the owner’s manual included with the tractor. Safety Precautions l Make sure the engine is off, ignition ke
Resumen del contenido incluido en la página 14
MAINTENANCE MAINTENANCE SCHEDULE Use the following maintenance schedule and the maintenance schedule shown in the tractor owner’s manual. INTERVAL I ACTION ITEM Before each use Every 25 hours Notes I Inspect Cover assembly Check pressure Tires NLGI #2 Wheels Lubricate 0 grease Cover Assembly l Check the condition of the cover before each use. If the cover is torn, worn or otherwise damaged, replace it before using the bagger cart. l Make sure the cover is not clogged with di
Resumen del contenido incluido en la página 15
ASSEMBLY THE IMPORTANCE OF ASSEMBLY Proper assembly is essential to operator safety and the reliability of the machine. Any error or oversight made by the technician assembling and servicing a unit can easily result in faulty operation, damage to the machine, or injury to the operator. Improper assembly can cause an unsafe condition that can cause your customer or others to be seriously hurt of killed. Follow the procedures and precautions in installation instructions and shop manuals ca
Resumen del contenido incluido en la página 16
ASSEMBLY REQUIREMENTS A separate mounting kit is required to install this bagger cart. Some tractor models also require a side blower kit too. DEALER: Order other required kits from Honda Dealer Services: Requirements 1 Tractor model 1 Honda Code I I HA41 18H38A MKC4138A mounting kit 612400 I I I HA41 20H48A MKC4148A mounting kit / BK4148A side-blower kit 1 612300 / 609800 1 I I other Honda See your Honda lawn tractor dealer for details. models TORQUE VALUES NUT AND BOLT TORQUE VA
Resumen del contenido incluido en la página 17
ASSEMBLY PARTS LIST Description Part Number Qty. Wheel assembly 2 81751-758-S61 Frame 81741-758-S61 U-bracket 81743-758-S61 Cart bed 81711-758-S61 Latch handle 81716-758-S61 Lift handle 81718-758-S61 Support tube 81721-758-S61 Frame rod 81722-758-S61 Support rod 1 81722-758-S61 Straight rod 1 81724-758-S61 1 81734-758-S61 Dump cloth rod BClOOO BAGGER CART 15
Resumen del contenido incluido en la página 18
ASSEMBLY * Lock washer, l/4” 4 * Self-locking nut, 5/l 6”-18 4 * Plastic spacer 2 * Hex bolt, 5/l 6”-18 x l,-l/2” 4 Circle clip, 1 -l/W 4 90654-758-S61 * commercially available 16 BClOOO BAGGER CART
Resumen del contenido incluido en la página 19
ASSEMBLY ASSEMBLY +- 3/B” HEX NUT (8) 1. Install the wheel assemblies on the frame, using eight 3/8 x l-inch hex bolts, eight 318 inch lock 3/8” LOCK washers, and eight 3/8-inch lock nuts. Take care WASHER (8) not to let the washers pinch the pivot seal on the wheel assembly. Torque the lock nuts to 15 ft-lb (3.5 kg-m, 34 Nom). 2. Apply grease to the grease fittings on the axles and swivels. GREASE: NLGI #2 multi-purpose grease. 3. Inflate the tires TIRE PRESSURE: 30 psi (207 kPa)
Resumen del contenido incluido en la página 20
ASSEMBLY 6. Turn the cart bed right side up. Install the latch l-114” HEX BOLT 5116 x handle, using a 5/16 x 1-l/4-inch hex bolt, two 5/l 6 inch friction washers, two 5/l 6 inch flat washers, and a 5/l 6 inch self-locking nut (nylon insert). When installing the hardware, position the friction 5/l 6” washers with the cupped side toward the latch FLAT handle. Torque the self-locking nut enough so the WASI latch handle will turn easily, but not .move when released. N 5118” FLAT WASH
