Resumen del contenido incluido en la página 1
No. 99MBA038A
SERIES No. 264
QM-Data 200
2D Data Processing Unit
User’s Manual
(Operation Guide)
Read this User’s Manual thoroughly
before operating the instrument. After reading,
retain it close at hand for future reference.
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
CONVENTIONS USED IN THIS MANUAL Types of Notes The following types of notes are used in this manual to help the operator obtain reliable measurement data through correct instrument operation. IMPORTANT • An important note provides information essential to the completion of a task. You cannot disregard this note to complete the task. • An important note is a type of precaution, which if neglected could result in a loss of data, decreased accuracy or instrument malfunction/failure.
Resumen del contenido incluido en la página 4
Introduction Thank you for using the “QM-Data 200” two-dimensional data processing unit. This Operation Guide presents a collection of example applications that will help you understand the basic operating procedures using the QM-Data 200. Effective use of this Operation Guide will ensure that you use the QM-Data 200 correctly, and will help you in your measurement work. Model Workpiece The model workpiece shown below is used in all the examples presented. This model workpiece is
Resumen del contenido incluido en la página 5
Table of Contents CONVENTIONS USED IN THIS MANUAL.........................................................................................................i Introduction.......................................................................................................................................................ii Model Workpiece ..............................................................................................................................................ii 1 Before St
Resumen del contenido incluido en la página 6
MEMO iv No. 99MBA038A
Resumen del contenido incluido en la página 7
1 Before Starting Measurements 1 This chapter presents practice on the preparations which precede measurements using this data processing unit. 1.1 Outline of Data Processing Unit 1.1.1 Appearance Display portion (LCD) Power switch Key panel Fig. 1-1-1 1-1 No. 99MBA038A
Resumen del contenido incluido en la página 8
1.1.2 Key Panel Layout Basic feature measurement AI measurement key command keys Function keys Screen switching key [LOAD] key Coordinate data [CANCEL] key input style key Coordinate [ENTER] key system alignment menu key Counter function key Measurement macro command keys Numeric keys User-defined menu keys Manual print key Cursor keys Fig. 1-1-2 Table 1-1-1 (No. 1) Key Function Basic feature measurement Used to measure and calculate basic geometric shapes. c
Resumen del contenido incluido en la página 9
1. Before Starting Measurements Table 1-1-1 (No. 2) Key Function Automatically recognizes the type of the measured basic feature and outputs AI measurement key the results when measured points are input. Switches the screen display mode (measurement screen, counter display Screen switching key screen, etc.). Counter function key Uses the data processing unit as a simple counter. Manual print key Prints the measurement results displayed on the screen. Executes a previously registered p
Resumen del contenido incluido en la página 10
1.1.4 Measurement Screen Measurement result window Navigation window Circle Counter Fig. 1-1-4 F1: Recalls the measured features and performs calculations, etc. F2: Recalls the measured features to adopt the representative point coordinates of those features as measured points for the current measurement. F3: Changes the measurement conditions ("Output Items", "Auto.MeasuringCompletion"). F4: (Enables/disables input
Resumen del contenido incluido en la página 11
1. Before Starting Measurements 1.2 Preparing for Measurement [Purpose of Practice] To learn the operating procedures from turning on the power to getting the state where measurement commands can be executed. [Operating Procedure] 1) Turn on the power for the data processing unit. 2) Set the printer output to ON. 1.2.1 Turning On the Power Table 1-2-1 No. Operation Screen display and remarks 1 Turn the power switch to ON. – 2 The Startup Screen is displayed. A little bit af
Resumen del contenido incluido en la página 12
1.2.2 Setting Printer Output to ON (when printer is connected) NOTE Be sure to turn on the printer power before setting the printer output to ON. Table 1-2-2 No. Operation Screen display and remarks MENU 1: Output Function Menu 1 Selecting menu function 7 8 9 Press . 4 5 2 Selecting printer setting Press the numeric key corresponding to – . Selecting ON for printer 3 Use the left and right cursor keys to select “All – Results w/o Command Names” for “Co
Resumen del contenido incluido en la página 13
2 Basic Measurements 2 This chapter presents practice for basic measurement procedures using the model workpiece. 2.1 Measuring a Circle [Purpose of Practice] To measure a circle using the model workpiece. φ4 Fig. 2-1-1 [Operating Procedure] Table 2-1-1 No. Operation Screen display and remarks 1 Preparing the workpiece Set the model workpiece on the XY table as shown below, and focus on it. – 2 Measurement function selection – Press . 2-1 No. 99MB
Resumen del contenido incluido en la página 14
No. Operation Screen display and remarks Measuring circle (A) 3 At any three points on the circumference of circle (A), Follow the information displayed on the center the projection screen crosshairs and then press the screen to perform the measurement. [LOAD] key. 1 (A) 2 3 4 Results display The circle (A) measurement results are displayed on the N0001 screen. X = *.*** Y = *.*** D = 4.018 Diameter D NOTE • The three points that are measured sho
Resumen del contenido incluido en la página 15
2. Basic Measurements 2.2 Measuring Angle Between Two Edges [Purpose of Practice] To measure the angle between two edges using the model workpiece. (B) (A) 150° Fig. 2-2-1 [Operating Procedure] Table 2-2-1 No. Operation Screen display and remarks Preparing the workpiece 1 Set the model workpiece on the XY table as shown below, and focus on it. – 2 Measurement function selection – Press . 3 Measuring edge (A) Measure edge (A) at two points. Follow the infor
Resumen del contenido incluido en la página 16
No. Operation Screen display and remarks Measuring edge (B) 4 Measure edge (B) at two points. Follow the information displayed on the 4 3 screen to perform the measurement. (B) 5 Results display The measurement results (A1, A2) for the angle formed by edge (A) and edge (B) are displayed on the screen. N0001 A2 X = *.*** Y = *.*** A1 A1= 150.0142 A2= 209.5818 NOTE • Note that the obtained angle (A1) varies depending on the order in which the edges
Resumen del contenido incluido en la página 17
2. Basic Measurements 2.3 Measuring a Width [Purpose of Practice] To measure a width using the model workpiece. 2 (B) (A) Fig. 2-3-1 [Operating Procedure] Table 2-3-1 No. Operation Screen display and remarks 1 Preparing the workpiece Set the model workpiece on the XY table as shown below, and focus on it. – 2 Measurement function selection – Press . 3 Measuring side (A) Follow the information displayed on the Measure side (A) at two points. (A) screen to
Resumen del contenido incluido en la página 18
No. Operation Screen display and remarks Measuring side (B) 4 Measure side (B) at one point. Follow the information displayed on the (B) screen to perform the measurement. 1 5 The width measurement result (LC) is displayed on the screen. LC N0001 LC= 2.001 NOTE When measuring a width, be sure to enter two points for the edge being measured first, and then enter one remaining point for the edge being measured second. TIP • If an incorrect position wa
Resumen del contenido incluido en la página 19
2. Basic Measurements 2.4 Measuring Distance Between Two Circles [Purpose of Practice] To measure two circles to obtain the distance between them. (B) (A) 4 Fig. 2-4-1 [Operating Procedure] Table 2-4-1 No. Operation Screen display and remarks Preparing the workpiece 1 Set the model workpiece on the XY table as shown below, and focus on it. – 2 Measurement function selection – Press . 3 Measuring circle (A) Measure circle (A) at three points. Follow the info
Resumen del contenido incluido en la página 20
No. Operation Screen display and remarks Measuring circle (B) 4 Measure circle (B) at three points. Follow the information displayed on the screen to perform the measurement. 1 (B) 2 3 Results display 5 The measurement results (LC, LS, LL) for the distance between circle (A) and circle (B) are displayed on the screen. N0001 LC= 4.006 LL= 6.011 LS= 2.001 XD= *.*** YD= *.*** (A) (B) LS LC LL TIP • The XD and YD measurement results indic
