Resumen del contenido incluido en la página 1
CRW4001t
SERIES
User Guide
Guide de I’utilisateur
Bedienungsanleitung
Resumen del contenido incluido en la página 2
COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Yamaha Systems Technology, Inc. Address: 100 Century Center Court San Jose, California 95112 Telephone: (408) 467-2330 FAX: (408) 437-8791 Type of Equipment: CD Recorder Model Name: CRW4001t CRW4001t-NB This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference receiv
Resumen del contenido incluido en la página 3
Laser Diode Properties CAUTION Material : GaAlAs Use of controls or adjustments or performance of Wavelength : 780-790 nm procedures other than those specified herein may Emission Duration : Continuous result in hazardous radiation exposure. Laser Output Power : Less than 44.6 μW* * This output is value measured at a distance 200mm from the objective lens surface on the optical pick-up block. ANSI Class : Class 1 This compact disc player is classified as a CLASS 1 LASER product. CLASS 1 LA
Resumen del contenido incluido en la página 4
WARNING ¢ WARNING ¢ • The temperature where CRW4001t is located should be between 5ºC and 40ºC (41ºF – 104ºF), when used in a fan-cooled system. • Do not disassemble the CRW4001t cover to reduce the risk of electric shock. • Always remove the disc before transporting CRW4001t. i
Resumen del contenido incluido en la página 5
Important Precautions Important Precautions Please read the following precautions before attempt- ing to operate the CRW4001t. • Before recording a disc, be sure to clean the disc and tray using an air aerosol-type dust remover. A dust particle on the disc may cause recording to fail, producing an unusable disc. • Always record in a dust-free environment. If the disc must be removed from the CRW4001t before recording is finished, store the disc in a clean, dust-free environment. • The C
Resumen del contenido incluido en la página 6
Table of Contents Table of Contents Introduction ............................................................................. 1 CRW4001t Features ...................................................... 1 Orange Book Compatible Recording ............................ 2 Chapter 1 - System Configuration ..................................... 3 Computer ....................................................................... 3 Software....................................................
Resumen del contenido incluido en la página 7
Introduction Introduction Thank you for purchasing a Yamaha CRW4001t drive. Please read this manual before using the drive in order to make the best use of the supe- rior CRW4001t functions. After reading, please retain this manual for future reference. CRW4001t Features n 2xS Recording (Rewritable) - 4xS Recording (Recordable) - 6xS Reading The CRW4001t is able to write (overwrite) CD-RW discs at double speed, and is able to write CD-R discs at quad speed, double speed, or
Resumen del contenido incluido en la página 8
Introduction Orange Book Compatible Recording Track at Once In this mode, data can be recorded to disc one track at a time. Discs recorded in this mode cannot be played in CD players or CD-ROM drives other than a CD-RW or CD-R drive until the session is closed. Multisession In this mode, data can be recorded to disc in stages (one session at a time). Additional data can be written later. Disc at Once In this mode, data can be recorded to an entire disc in one pass. It is not poss
Resumen del contenido incluido en la página 9
Chapter 1 - System Configuration Chapter 1 - System Configuration Before using the CRW4001t, make sure that you have all of the items on the list of included items. In order to use the CRW4001t, you will require the following. Computer The following operating environment is required: • An IBM/AT compatible computer with a 100 MHz or faster Pentium CPU (in order to write at 4x speed), or a 100 MHz or faster 486 CPU (in order to write at 2x speed) • A vacant IDE interface connector
Resumen del contenido incluido en la página 10
Chapter 1 - System Configuration Discs On the CRW4001t, you can use conventional CD-RW and CD-R discs that conform to the Recordable Compact Disc Systems Part 2 and Part 3 (Orange Book). Yamaha recommends the following Yamaha CD-RW and CD-R discs: CD-RW Discs > CRWM74R (f 120mm, 74 minutes) CD-R Discs > CDM12Y63 (f 120mm, 63 minutes) > CDM12Y74 (f 120mm, 74 minutes) > CDM12Y74M (f 120mm, 74 minutes) > CDM12Y74T (f 120mm, 74 minutes) Read-only Discs You can use discs with t
Resumen del contenido incluido en la página 11
Chapter 2 - Installing the Yamaha CRW4001t Drive Chapter 2 - Installing the Yamaha CRW4001t Drive MASTER/SLAVE settings Before you install the CRW4001t in your computer, you must make the MASTER/SLAVE setting. This setting is set by inserting a jumper pin in the jumper switch located on the rear panel of the CRW4001t drive. Important: When the unit is shipped from the factory, this setting is in the MASTER position. Note: Use long-nose pliers to remove or insert the jumper pin.
Resumen del contenido incluido en la página 12
Chapter 2 - Installing the Yamaha CRW4001t Drive ' Setting the CRW4001t as the MASTER As shown in the diagram at the right, insert the CSEL T jumper pin into the right edge of the jumper SLAVE MASTER switch. IDE INT Note: If only the CRW4001t will be connected to the IDE interface connector, connect the CRW4001t to the end of the connector. ' Setting the CRW4001t as the SLAVE As shown in the diagram at the right, insert the CSEL T jumper pin into the middle of the jumper switch. S
Resumen del contenido incluido en la página 13
OFF Chapter 2 - Installing the Yamaha CRW4001t Drive Installing the CRW4001t drive The following steps will differ slightly depending on the type of computer you are using. For details on removing the cover from your computer, and installing or removing internal devices, refer to the manual for your computer. 1. Switch off your computer, and unplug it from the AC outlet. If you fail to do this, there is a danger of electric shock and/or of causing short circuits, which may damage t
Resumen del contenido incluido en la página 14
Chapter 2 - Installing the Yamaha CRW4001t Drive 4. Remove the front cover of a vacant half-height drive bay. For details refer to the manual of your computer. 5. Slide the CRW4001t drive into the drive bay from the front. At this time, be careful not to apply excessive force to the drive itself. Finger-tighten the four fastening screws, and check that there is enough room to connect the power supply cable, IDE interface connector, and AUDIO cables. 6. Connect the IDE interface con
Resumen del contenido incluido en la página 15
Chapter 2 - Installing the Yamaha CRW4001t Drive 7. Connect the AUDIO cable. Connect the single 4-pin connector (Sound Blaster compatible) to the sound card. Connect the 4-pin connector at the other end of the cable (the larger connector) to the AUDIO OUT connector on the CRW4001t drive. The polarizing lug should be at the top. AUDIO Cable To the CRW4001t 4-pin connector (large) To the CDR100/102 (3-pin connector) * Simultaneous use with the CRW4001t is not possible. To the Sound Card
Resumen del contenido incluido en la página 16
Chapter 2 - Installing the Yamaha CRW4001t Drive 8. Connect the power supply cable. Connect the +12V and +5V 4-pin power cable to the power supply inter- face located on the rear panel of the CRW4001t drive. The shape of the connector makes it impossible to reverse the connections. DC INPUT I/F 4 3 2 1 +5V±5% G +12V±10% DC INPUT 9. Tighten the four fastening screws securely. 10 CSEL SER. NO. AUDIO OUT DC INPUT SLAVE MASTER RGL 1 +5V G +12V IDE INTERFACE CONNECTOR
Resumen del contenido incluido en la página 17
ON Chapter 2 - Installing the Yamaha CRW4001t Drive 10. Attach the cover of your computer. 11. Connect the power cable to an AC outlet, and switch on your computer. Make sure that the LED located on the panel of the CRW4001t drive is lit. PUSH 12. Start up your operating system. For the procedure, refer to the manual for your operation system. 13. Install the writing software. For the installation procedure, refer to the manual for your writing soft- ware. 11
Resumen del contenido incluido en la página 18
Chapter 3 - Operation Chapter 3 - Operation Front Panel 1 6 23 4 5 1 Disc tray The disc is inserted and ejected here. Pressing the eject button will open the tray. 2 Headphone jack This stereo mini jack allows you to connect headphones and listen to audio. 3 Headphone volume control This control adjusts the volume level of the headphone output. Rotating the control clockwise will increase the volume level. 4 ON/DISC LED This indicator lights up in orange when the CRW4001t is powered on, and
Resumen del contenido incluido en la página 19
Chapter 3 - Operation Loading a Disc 1. Press the eject button to open the tray. 2. Carefully place the disc, label-side up, on the disc tray. 3. Press the disc tray softly or press the eject button again to close the disc tray. 13 ON/ READ/ DISC WRITE VOL Recordable
Resumen del contenido incluido en la página 20
Chapter 3 - Operation Ejecting the Disc If the CRW4001t is powered on: Press the eject button to eject the disc. Note: You cannot eject the disc if the ATAPI command prohibits the eject opera- tion while the CRW4001t is reading data. Caution: Be sure to remove the disc after it is completely ejected. (Trying to remove the disc before it is completely ejected may cause the drive to malfunction.) Press the eject button If the CRW4001t is not powered on: Pressing the eject button will not eject t
