Resumen del contenido incluido en la página 1
ESPAÑOL: PÁGINA 15
FRANÇAISE : PAGE 29
Instruction
manual
Double Insulated Random
Orbit 5" Sander/6" Polisher
MODELS - 7335, 7336,
7336SP, 7355, 7366, 7424
IMPORTANT
To learn more about Porter-Cable Please make certain that the person who is
visit our website at: to use this equipment carefully reads and
understands these instructions before
http://www.porter-cable.com
starting operations.
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spac
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . .2 SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ADDITIONAL SPECIFIC SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . .6 ADDITIONAL SAFETY RULES FOR PAINT REMOVAL . . . . . . . . . . . . .8 CARTON CONTENTS . . . . . . . . . . . . . . . . . . . . .
Resumen del contenido incluido en la página 3
SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided,could result in death or serious injury. indicates a potentially hazardous situ
Resumen del contenido incluido en la página 4
GENERAL SAFETY RULES Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS 1) Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the pr
Resumen del contenido incluido en la página 5
GENERAL SAFETY RULES continued d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair
Resumen del contenido incluido en la página 6
ADDITIONAL SPECIFIC SAFETY RULES 1. Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 2. Use proper safety equipment. Wear safety goggles for eye protection, wear hearing protection, and wear a protective mask to minimize breathing in the fine dust created while sanding. 3. Always disconnect the sander cor
Resumen del contenido incluido en la página 7
SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µF ........................ microfarads l ........................ litres g ........................ grams kg ........................ kilograms bar ........................ bars Pa ........................ pascals h ........................ hours min .......................
Resumen del contenido incluido en la página 8
ADDITIONAL SAFETY RULES FOR PAINT REMOVAL Extreme care should be taken when removing paint. The peelings, residue, and vapors of paint may contain lead, which is poisonous. Exposure to even low levels of lead can cause irreversible brain and nervous system damage. Young and unborn children are particularly vulnerable. Before beginning any paint removal process you should determine whether the paint you are removing contains lead. This can be done by your local health department or by a professio
Resumen del contenido incluido en la página 9
MOTOR Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C. current only. Refer to the specification plate on your tool for proper voltage and current rating. Do not operate your tool on a current on which the voltage is not within correct limits. Do not operate tools rated A.C. only on D.C. current. To do so ma
Resumen del contenido incluido en la página 10
ASSEMBLY NOTE:This tool is shipped completely assembled. No assembly time or tools are required. A AUXILIARY HANDLE An auxiliary handle (A) Fig. 1 is furnished with the tool. You can install the auxiliary handle on either side of the front housing to facilitate either right-handed or left-handed operation. Fig. 1 Use this handle at all times to maintain complete control of the tool. OPERATION TO START AND STOP TOOL Make certain that the switch is in the “OFF” position, and the power source is th
Resumen del contenido incluido en la página 11
USING THE POLISHER If your workpiece is so light that it can be moved by the rotating pad, anchor it securely to prevent possible bodily injury. 1. Read and follow the directions supplied with the product (polishes, waxes, cleaners, etc.). 2. Apply a small amount of the product directly to the polishing pad. 3. Grasp the polisher firmly with both hands - one hand on auxiliary handle and one hand on motor housing (Fig. 4). 4. Position the polisher with the polishing pad against the work surface a
Resumen del contenido incluido en la página 12
USING THE SANDER Secure the workpiece to prevent it from moving. Friction between the sanding disc and the workpiece can spin the workpiece away from sander and may cause bodily injury. Wear ANSI Z87.1 safety glasses and dust mask. 1. Place the sander on the workpiece (Fig. 6) with the abrasive disc resting flat on the workpiece. NOTE: The random orbiting mechanism allows you to start or stop the sander in or out of contact with the workpiece. 2. Grasp the sander firmly and Fig. 6 move switch to
Resumen del contenido incluido en la página 13
TROUBLESHOOTING For assistance with your tool, visit our website at www.porter-cable.com for a list of service centers or call the Porter-Cable help line at 1-800-487-8665. MAINTENANCE KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed air. FAILURE TO
Resumen del contenido incluido en la página 14
SERVICE REPLACEMENT PARTS When servicing use only identical replacement parts. For a service parts list or to learn more about Porter-Cable visit our website at www.porter-cable.com SERVICE AND REPAIRS All quality tools will eventually require servicing, or replacement of parts due to wear from normal use. For assistance with your tool, visit our website at www.porter-cable.com for a list of service centers or call the Customer Care Department at 1-800-487-8665. All repairs made by our service c
Resumen del contenido incluido en la página 15
PORTER-CABLE DELTA SERVICE CENTERS (CENTROS DE SERVICIO DE PORTER-CABLE DELTA) (CENTRE DE SERVICE PORTER-CABLE DELTA) Parts and Repair Service for Porter-Cable Delta Power Tools are Available at These Locations (Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable Delta) (Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien) ARIZONA GEORGIA MINNESOTA Cleveland 44125 Tempe 85282 (Phoenix) Forest Pa
