Resumen del contenido incluido en la página 1
WINE-MATE Cooling Unit
Use & Care Manual
VINO1500CD, CTED
VINO2500CD, CTED
Vinotemp International Corp.
Vinotemp International Corp.
www.winemate.com
www.winemate.com
Resumen del contenido incluido en la página 2
Important Safety Information • DO NOT PLUG IN UNTIL 24 HOURS AFTER DELIVERY. • DO NOT USE A GROUND FAULT INTERRUPTER (GFI). • A DEDICATED 15 AMPCIRCUIT IS HIGHLY RECOMMENDED. - 1 -
Resumen del contenido incluido en la página 3
TABLE OF CONTENTS Feature Description…………………………….……………..3 Installation Instruction………………………………………..5 Temperature Control & Humidity Adjustment………….8 Care Guide……………………………………………………11 Troubleshooting……………………………………………..12 Wiring Diagram……………………………………….………15 Customer Support……………………………………………16 Warranty……………………………………………………….17 - 2 -
Resumen del contenido incluido en la página 4
Feature Description • VINO1500CD, CTED and VINO2500CD, CTED cooling units are designed and used to provide a subtle temperature between 50~65 °F for suitable space at a normal environment. • The refrigerated space will maintain humidity of 50~70% RH even when the environment becomes dry and humid. • These temperatures and humilities are optimized for long term storage of wine. • Bottom cold-air supply is optimized for use in the wine cabinets. • Multiple options for top and rear h
Resumen del contenido incluido en la página 5
Fig. 1.2 DIMENSIONS (in) The dimension and capacity are specified as follows: Cooling Bottle Model Exhaust Electrical Weight Capacity, CFM Capacity 55°F/ 75°F 55°F/ 75°F 1500 Btu/h, 150 800 115V/60Hz 1500cd 50 lb Rear Exhaust 120 CFM cu ft bottles 4A 1500 Btu/h, 150 800 115V/60Hz 1500cted Top Exhaust 50 lb 120 CFM cu ft bottles 4A 2500 Btu/h, 250 1200 115V/60Hz 2500cd Rear Exhaust 55 lb 180 CFM cu ft bottles 5A 2500 Btu/h, 250 1200 115V/60Hz 2500cted Top Exhau
Resumen del contenido incluido en la página 6
Installation Instruction 1. Cabinet Location • Place the wine cabinet in a properly ventilated location. Otherwise, heat exhausted by the cooling unit will build up and it will not operate properly. • The exhaust area must not be a closed space and must be ventilated. The ambient temperatures shall not be higher than 90 °F or lower than 50 °F. 1) Rear Exhaust Location • Leave min 6 “clearance from the rear to the wall. • Leave min 12” clearance from the top to the ceiling. • Le
Resumen del contenido incluido en la página 7
Fig. 2.2 MOUNTING CUTOUT & GASKET LIPS (LOCATED AT THE CABINET) Fig. 2.3 TOP EXHAUST GASKET (LOCATED ON THE COOLING UNIT) - 6 -
Resumen del contenido incluido en la página 8
• Cut a rectangular inside opening at the rear of the cabinet with the 1/4” clearance inwards to the width and height of the cooling unit. By not going through, leave 1/2” lip inside at the wall to place the gaskets (see Fig. 2.2). • If top exhaust, cut another rectangular opening at the top of the cabinet to the length and width of the top exhaust (see Fig.2.2). • Make 2 holes at the ceiling to install the 1/4 inside diameter wood thread inserts (see Fig.2.2). • Place the gaskets (1) on
Resumen del contenido incluido en la página 9
Temperature Control & Humidity Adjustment 1. Temperature Setting • Set the temperature at 55 °F for the optimum aging of wine • On initial start-up, the time required to reach the desired temperature will vary, depending on the quantity of bottles, temperature setting and surrounding temperature. • Allow 24 hours to stabilize the temperature for each new temperature setting operation 2. Use of the controller Fig. 3.1 DIGITAL CONTROLLER 1) Display During normal operating co
Resumen del contenido incluido en la página 10
2) Alarm Signals 2.1 Code Description 2.2 Alarm Recovery Probe alarms P1”, start a few seconds after the fault in the related probe; they automatically stop a few seconds after the probe restarts normal operation. Check connections before replacing the probe. Temperature alarms “HA”, “LA” automatically stops as soon as the temperature returns to normal value. Alarm “CA” (with i1F=PAL) recovers only by switching off and on the instrument. 3) Temperature Set-Point 3.1 How to
Resumen del contenido incluido en la página 11
2. The value of the set point will be displayed and the “°C” or “°F” LED starts blinking; 3. To change the Set value, push the keys or arrows within 10s. 4. To memorize the new set point value, push the SET key again or wait 10s. 4) Humidity Adjustment The parameter Fon is used to adjust the humidity in the wine cabinet. The higher value of Fon, the higher relative humidity will be. 1. Press the Set + keys for 3 sec until the “°C” or “°F” LED starts blinking. 2. Release the keys, t
Resumen del contenido incluido en la página 12
Care Guide I I. Condenser Coil Cleaning • The condenser coil is on the ambient air intake side of the cooling unit. • Clean the condenser coil regularly. Coil may need to be cleaned at least every 6 months. • Unplug the cooling unit or disconnect power. • Use a vacuum cleaner with an extended attachment to clean the coil when it is dusty or dirty. • Plug the cooling unit or reconnect power. II. Moisture Removing • Remove the extra condensate if it is accumulated in the wine
Resumen del contenido incluido en la página 13
Troubleshooting This Troubleshooting Chart is not prepared to replace the training required for a professional refrigeration service person, not is it comprehensive Troubleshooting Chart Complaint Possible Causes Response a. Power cord unplugged a. Check for power cord plug 1.Unit not b. No power to unit b. Check power at receptacle & fuses running c. Setting higher than ambient c. Lower temperature setting temperature d. Differential too high d. Decrease the value as to 4 °F e
Resumen del contenido incluido en la página 14
a. Improper room insulation & seal a. Check for insulation, gasket and 6. “HA” alarm door opening blinking and b. Room too large b. Check for excessive size beeping, c. Ambient temperature too high c. Check for installation location temperature d. Exhaust restricted d. Leave minimum 3 feet clearance for high or not the exhaust side and leave minimum 1 foot clearance for the cooling and fresh air intake side running e. Malfunctioning fans e. Check for both evaporator and c
Resumen del contenido incluido en la página 15
f. Refrigerant low or leaking f. Check for current and sealed system leakage g. Capillary tube blockage g. Check for low side pressure a. High humidity a. Use drain line 11.Water leak b. Air leak in wine cellar b. Check for any air leak c. Evaporator air flow restriction c. Check air flow or air TD crossing evaporator d. Water passages restricted d. Clean the drip tray e. Drip tray leak e. No water overflow but leak a. Incorrect fuse or breaker a. Check for proper fuse or breaker
Resumen del contenido incluido en la página 16
Wiring Diagram Fig. 6.1 WIRING DIAGRAM Fig. 6.2 CALLING FEATURE WIRING DIAGRAM - 15 -
Resumen del contenido incluido en la página 17
Customer Support If you still have problems, please contact us at: Vinotemp International 17631 South Susana Road Rancho Dominguez, CA 90221 Tel: (310) 886-3332 Fax: (310) 886-3310 Email: info@vinotemp.com - 16 -
Resumen del contenido incluido en la página 18
Warranty Thank you for choosing a Vinotemp cooling unit. Please enter the complete model and serial numbers in the space provided: Model_________________________________________________________ Serial No.______________________________________________________ Attach your purchase receipt to this owner’s manual. 1. Limited Warranty VINOTEMP warrants its products to be free from defects due to workmanship or materials under normal use and service, for twelve mont
Resumen del contenido incluido en la página 19
is determined to be faulty and is within the twelve month warranty period VINOTEMP will, at its discretion, repair or replace the unit and return it free of charge to the original retail customer. If the unit is found to be in good working order, or beyond the initial twelve month period, it will be returned freight collect. 2. Limitation of Implied Warranty VINOTEMP’S SOLE LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO, AT OUR OPTION, REPAIRING OR REPLACING OF UNIT. VINOTEMP SHA
