Manual de instrucciones de Kenwood KDC-138

Resumen del contenido incluido en la página 15

Accessories/ Installation Procedure If you use the wrong screws, you could damage the unit. Accessories • If the power is not turned ON (“PROTECT”/”DCER” is displayed), the speaker wire may have a short-circuit or touched the chassis of the vehicle and the protection 1 function may have been activated. Therefore, the speaker wire should be checked. • If your car’s ignition does not have an ACC position, connect ..........1 the ignition wires to a power source that can be turned on and off

Resumen del contenido incluido en la página 16

Connecting Wires to Terminals Front preput(KDC-MP238 only) To Kenwood disc changer/ External optional accessory (KDC-MP238 only) Rear preput/ Subwoofer preput (KDC-MP238/MP238CR/MP208/138 only) FM/AM antenna input Fuse (10A) Wiring harness (Accessory1) If no connections are made, do not let the wire come out from the tab. Power control/Motor antenna control wire Connect either to the power control terminal (Blue/White) when using the optional power amplifier, or to P.CONT the antenna contr

Resumen del contenido incluido en la página 17

Installation non-Japanese cars Removing the hard rubber frame 1 Engage the catch pins on the removal tool and Metal mounting strap (commercially available) remove the two locks on the upper level. Upper the frame and pull it forward as shown in Firewall or metal support the figure. Lock Catch Accessory2 Bend the tabs of the Removal tool mounting sleeve with a screwdriver or similar utensil 2 When the upper level is removed, remove the and attach it in place. lower two locations. Self-tappi

Resumen del contenido incluido en la página 18

Troubleshooting Guide Some functions of this unit may be disabled by The messages shown below display your some settings made on this unit. systems condition. TOC ERR/E-04: • No disc has been loaded in the disc ! Cannot display the user of System Q. magazine.

Resumen del contenido incluido en la página 19

Specifi cations FM tuner section Audio section Frequency range Maximum output power 200 kHz space : 50 W x 4 : 87.9 MHz – 107.9 MHz Full Bandwidth Power (at less than 1% THD) : 22 W x 4 50 kHz space (KDC-MP238CR/138CR) Speaker Impedance : 87.5 MHz – 108.0 MHz : 4 – 8 Ω Usable sensitivity (S/N = 30dB) Tone action : 9.3dBf (0.8 μV/75 Ω) Bass : 100 Hz ±8 dB Quieting Sensitivity (S/N = 50dB) Middle : 1 kHz ±8 dB : 15.2dBf (1.6 μV/75 Ω) Treble : 10 kHz ±8 dB Frequency response (±3 dB) Preout

Resumen del contenido incluido en la página 20

Table des matières Avant l’utilisation 21 Appendice 32 Fonctionnement basique 22 Accessoires/ Procédure d’installation 33 Fonctions générales Fonctions du tuner Connexion des câbles aux bornes 34 Fonctions de la lecture de disque Fonctionnement général 24Installation 35 Commande du son Guide de depannage 36 Réglage audio Réglage des enceintes Spécifications 37 Commutation de l’affichage Fonctionnement du tuner 26 Réglage de l'intervalle de fréquence Fonctionnement des disques audio/ fichiers au

Resumen del contenido incluido en la página 1

KDC-MP238/CR
KDC-MP208
KDC-138/CR
CD-RECEIVER
INSTRUCTION MANUAL
AMPLI-TUNER LECTEUR DE CD
MODE D’EMPLOI
REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM
MANUAL DE INSTRUCCIONES
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best
performance from your new CD-receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the
warranty card, and in the space pr

Resumen del contenido incluido en la página 2

Contents Before use 3 Appendix 14 Basic Operation 4 Accessories/ Installation Procedure 15 General functions Connecting Wires to Terminals 16 Tuner functions Disc play functions Installation 17 General Operation 6 Troubleshooting Guide 18 Audio Control Audio Setup Specifications 19 Speaker Setting Switching Display Tuner Operation 8 Frequency Step Setting Music disc/Audio file Operation 9 Direct Music Search Direct Disc Search Folder Select Menu Operation 10 Menu System Activating Security Code

Resumen del contenido incluido en la página 3

Before use • If you experience problems during installation, 2WARNING consult your Kenwood dealer. To prevent injury or fire, take the following • When you purchase optional accessories, check with precautions: your Kenwood dealer to make sure that they work • To prevent a short circuit, never put or leave any with your model and in your area. metallic objects (such as coins or metal tools) inside • The characters which can be displayed by this unit the unit. are A-Z 0-9 @ " ‘ ` % & * + –

Resumen del contenido incluido en la página 4

Basic Operation Disc slot Release Display Control [ ] Auxiliary input knob [VOL] [SRC] [1] [2] [3] [4] [5] [6] [AUTO] [B.BOOST] exposed to direct sunlight, excessive heat or humidity. Also General functions avoid places with too much dust or the possibility of water splashing. Power/Source Select button [SRC] • To prevent deterioration, do not touch the terminals of the Turns on the power. unit or faceplate with your fingers. When the power is on, the source switches between Tuner (“TUNER”

Resumen del contenido incluido en la página 5

: Indicates the button etc. to operate. Tuner functions Disc ejection [0] ⁄ Band select Control knob • You can eject the disc for 10 minutes after switching off the Switches between FM1, FM2, and FM3 each time the engine. top side is pressed. Music search Control knob Switches to AM when the bottom side is pressed. Changes the music when the left or right side is Tuning Control knob pressed. Changes the frequency when the left or right side is Fast reverses or forwards the music while