Resumen del contenido incluido en la página 1
®
Gas Dryer
Secadora a Gas
Models/Modelos 110.9756", 9757", 9758"_
= color number/n0mero de color
W10035060 Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com
Resumen del contenido incluido en la página 2
TABLEOF CONTENTS WARRANTY ..................................................................................... 2 Stopping or Restarting Your Dryer ............................................ 17 Lock Controls ............................................................................ 17 DRYER SAFETY .............................................................................. 3 Drying and Cycle Tips ............................................................... 17 INSTALLATION INSTRUCTIONS .
Resumen del contenido incluido en la página 3
PRODUCT RECORD PEDESTAL PRODUCT RECORD In the space below, record your complete model number, serial In the space below, record your complete model number, serial number, and purchase date. You can find this information on the number, and purchase date. You can find this information on the model and serial number label located on the product. model and serial number label located on the product. Have this information available to help you obtain assistance or Have this information available to h
Resumen del contenido incluido en la página 4
IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions, including the following: [] Read all instructions before using the dryer. [] Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this [] Do not place items exposed to cooking oils in your dryer. Use and Care Guide or in published user-repair Items contaminated with cooking oils may contribute
Resumen del contenido incluido en la página 5
INSTALLATION INSTRUCTIONS Gather the required tools and parts before starting installation. Are you placing the dryer on a pedestal? You can purchase a Read and follow the instructions provided with any tools listed pedestal separately for this dryer. This pedestal will add about here, 10" (25.4 cm) to the height of your unit for a total height of approximately 46" (116.8 cm), • Level 8" or 10" pipe wrench For a garage installation, you will need to place the dryer at least 8" or 10" adjustable
Resumen del contenido incluido en la página 6
Alevel floorwithamaximum slope of1"(2.5 cm)under entire Custom undercounter installation - Dryer only dryer. (Ifslope isgreater than1"[2.5cm],install Extended .... 2"* Dryer FeetKit,PartNo.279810.) Clothes maynottumble properly andautomatic sensor cycles may notoperate 36"rnin {_"_ correctly ifdryerisnotlevel. Donotoperate yourdryer attemperatures below 45°F (7°C). At lower temperatures, thedryer might notshutoffattheendofan "'il I automatic cycle. Drying times canbeextended. 1"* _ "_""-27"----_
Resumen del contenido incluido en la página 7
Mobile home - additional installation requirements Installation spacing for cabinet installation This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home [] The dimensions shown are for the recommended spacing. Construction and Safety Standard, Title 24 CFR, Part 3280 [] For cabinet installation, with a door, minimum ventilation (formerly the Federal Standard for Mobile Home Construction openings in the top of the cabinet are required, and Safe
Resumen del contenido incluido en la página 8
• %" approved aluminum or copper tubing is acceptable for lengths under 20 ft (6.1 m) if local codes and gas supplier permit. • If you are using Natural gas, do not use copper tubing. • %" flare x %" NPT adapter fitting between dryer pipe and %" approved tubing. • Lengths over 20 ft (6.1 m) should use larger tubing and a different size adapter fitting. Explosion Hazard • If your dryer has been converted to use LP gas, %" LP compatible copper tubing can be used. If the total length of Use a new C
Resumen del contenido incluido en la página 9
• Replace any plastic or metal foil vent with rigid or flexible Dryer gas pipe heavy metal vent. • Review Vent system chart. Modify existing vent system if • The gas pipe that comes out through the rear of your dryer necessary to achieve the best drying performance. has a %" male pipe thread. If this is a new vent system B Vent material (15.9 cm) • Use a heavy metal vent. Do not use plastic or metal foil vent. • 4" (10.2 cm) heavy metal exhaust vent and clamps must be used. DURASAFF Mventing pro
Resumen del contenido incluido en la página 10
Clamps The angled hood style (shown here) is acceptable. • Use clamps to seal all joints. • Exhaust vent must not be connected or secured with screws or other fastening devices that extend into the interior of the duct. Do not use duct tape. (6.4 crn) An exhaust hood should cap the vent to keep rodents and insects from entering the home. Clamp Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in the path of the exhaust (such as Exhaust flowers, rocks or bushes
Resumen del contenido incluido en la página 11
Alternate installations for close clearances Choose your exhaust installation type Venting systems come in many varieties. Select the type best for your installation. Two close-clearance installations are shown. Recommended exhaust installations Refer to the manufacturer's instructions. Typical installations vent the dryer from the rear of the dryer. Other installations are possible. B i/ I II A ..... ................. F ................................... G A B A. Over-No-top installation (also
Resumen del contenido incluido en la página 12
Determine vent length and elbows needed for best drying performance • Use the following Vent system chart to determine type of vent material and hood combinations acceptable to use. Excessive Weight Hazard • NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust systems longer than those Use two or more people to move and install dryer. specified will: Failure to do so can result in back or other injury. • Shorten the life of the dryer. • Reduce performance, res
Resumen del contenido incluido en la página 13
4. Once the exhaust vent connection is made, remove the corner posts and cardboard. 1= Remove the red cap from the gas pipe. 2. Using a wrench to tighten, connect the gas supply to the dryer. Use pipe-joint compound on the threads of all non- Check the levelness of the dryer. Check levelness first flared male fittings. If flexible metal tubing is used, be sure side to side, then front to back. there are no kinks. A. Flared male fitting If the dryer is not level, prop up the dryer using a wood bl
Resumen del contenido incluido en la página 14
5. Rotate outer door 180 °. 6. Reassemble the inner and outer door assemblies with the 6 screws. 180 ° Reverse hinge 1. Use a small flat-blade screwdriver to remove 2 plug strips from the inner door. Slide the head of the screwdriver under Reverse the strike the plugs, being certain not to scratch the inner door surface. Lift up. 1. Use a small flat-blade screwdriver to remove plug strip from the dryer door opening. Slide the head of the screwdriver under the plugs, being certain not to scratch
Resumen del contenido incluido en la página 15
1. Check that all parts are now installed. If there is an extra part, 7. Remove any protective film or tape remaining on the dryer. go back through the steps to see which step was skipped. 8. Read "Dryer Use." 2. Check that you have all of your tools. 9. Wipe the dryer drum interior thoroughly with a damp cloth to 3. Dispose of/recycle all packaging materials. remove any dust. 4. Check the dryer's final location. Be sure the vent is not 10. Select a Timed Dry heated cycle, and start the dryer. D
Resumen del contenido incluido en la página 16
DRYER USE STATUS AUTO MODIFIERS & OPTIONS Power CYCLES Delicate Wet_ 0 TIMED I igh Damp _ Casual CYCLES Cool Down _ Timed Medium High Clothes Dry Ja_t _ More Dry Medium Wrinkle Guard O _ Normal Jeans Express Dry 0 Less Low O Wrinkle Guard 90 Controls Locked _ Touch Up Extra Low V Check Lint Screen Air 0nly Dryness Level AU-OCYC!So,,JY O D Cycle Signal Temperature LOCi/NLOCK CONTROLS _pJusSll_/cyc _ o_1¥ Explosion Hazard Fire Hazard Keep flammable materials and vapors, such as No washer can compl
Resumen del contenido incluido en la página 17
To use a Timed Cycle Select a Timed Cycle. This feature allows you to lock your settings to avoid unintended Press MORE TIME or LESS TIME until the desired drying use of the dryer. You can also use the control lock feature to time is displayed. Tap MORE TIME or LESS TIME and the time will change by 1-minute intervals. Press and hold avoid unintended cycle or option changes during dryer operation. MORE TIME or LESS TIME, and the time will change by To enable the control lock feature: 5-minute int
Resumen del contenido incluido en la página 18
Follow the progress of your dryer with the drying Status indicator Select the drying cycle that matches the type of load you are lights. drying. See the Auto Cycles Preset Settings chart or the Timed Cycles Preset Settings chart. STATUS AUTO CYCLES Delicate wet? TIMED Damp? Casual CYCLES Cool Down? Normal Timed ClothesDry9 Dry Wrinkle GuardO Jeans Express Dry ControlsLocked Heavy Duty Up CheckLint Screen Wet The Wet light illuminates at the beginning of an Auto Cycle if a AU'_} CYCLES wet item i
Resumen del contenido incluido en la página 19
Auto Cycles Preset Settings Use Modifiers to select temperatures for the Timed Cycles only. Auto Cycles Load Type Temperature Time* Press Temp Adjust until the desired temperature setting glows. (Minutes) Temperature modifiers cannot be used with the Auto Cycles. HEAVY DUTY High 45 High Heavyweight mixed loads, towels Medium High Medium JEANS Medium High 55 Denim pants, jackets Low NORMAL Medium 40 ExtraLow Sheets, corduroys, sturdy work clothes Air 0nly CASUAL Low 35 © Permanent press, syntheti
Resumen del contenido incluido en la página 20
You can customize your cycles by selecting options. The dryer rack is shipped in place in your dryer. Remove and discard any packing material before use. Use the TUMBLE FREF M Non-Heated Dryer Rack for items that O WrinkleGuard90 you do not want to tumble dry, such as sweaters. To use the dryer rack Do not remove the lint screen. 1. Open dryer door. LOCK/ bNLOCKCONIROLS WRINKLE GUARD e_90 WRINKLE GUARD ®90 helps smooth out wrinkles that form when you cannot unload the dryer promptly at the end o
