Resumen del contenido incluido en la página 1
GEAppliances.com
Safety Instructions . . . . . . . . . . . . . 2–5
Owner’s Manual &
Installation Instructions
Operating Instructions
Care and Cleaning . . . . . . . . . . . . . . . . . . . . .8
U.S. Models:
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
DSXH43
Loading and Using the Dryer . . . . . . . . . . .8
DPXH46
DH43
Installation Instructions . . . . . . 9–20
Electrical Installation for
Canada Mod
Resumen del contenido incluido en la página 2
IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING. WARNING! For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or death. ■ Do not store or use gasoline or other ■ Installation and service must be performed flammable vapors and liquids in the by a qualified installer, service agency or vicinity of this or any other appliance. the gas supplier. WHAT TO DO IF YOU S
Resumen del contenido incluido en la página 3
Safety Instructions Operating Instructions Installation Instructions Troubleshooting Tips Consumer Support PROPER INSTALLATION This dryer must be properly installed and located in accordance with the Installation Instructions before it is used. ■ Properly ground dryer to conform with all Exhaust/Ducting: governing codes and ordinances. Follow This dryer MUST be exhausted to the outside. details in Installation Instructions. 1 Use only rigid metal 4″ diameter ductwork ■Install or store where it w
Resumen del contenido incluido en la página 4
IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING. WARNING! YOUR LAUNDRY AREA ■ Keep the area underneath and around your ■ Close supervision is necessary if this appliance is appliances free of combustible materials, such used by or near children. Do not allow children as lint, paper, rags and chemicals. to play on, with or inside this or any other appliance. ■ Keep the floor around your appliances clean and dry to reduce the possibility of slipping. ■ Keep all laundry aids (such
Resumen del contenido incluido en la página 5
Safety Instructions Operating Instructions Installation Instructions Troubleshooting Tips Consumer Support WARNING! ■ Never attempt to operate this appliance if ■ You may wish to soften your laundered fabrics it is damaged, malfunctioning, partially or reduce the static electricity in them by using disassembled or has missing or broken parts, a dryer-applied fabric softener or an antistatic including a damaged cord or plug. conditioner. We recommend you use either a fabric softener in the wash
Resumen del contenido incluido en la página 6
About the dryer control panel. Models DPXH46 and DCXH46 Models DSXH43, DH43 and PSXH43 Features and appearance may vary. Control Settings Fabric Care COTTONS For regular to heavy cottons. REG. HEAT PERM. PRESS For synthetics, blends and items labeled permanent press or tumble dry medium heat. MED HEAT KNITS/ For knits, delicates, synthetics and items labeled tumble dry low heat. DELICATES LOW HEAT AIR FLUFF For fluffing items without heat. Use the TIMED DRY cycle. NO HEAT Drying Cycles The COTTO
Resumen del contenido incluido en la página 7
Safety Instructions Operating Instructions Installation Instructions Troubleshooting Tips Consumer Support About your dryer features. Cycle Signal Option (on some models) CYCLE SIGNAL When the signal is on it will sound just five minutes as a reminder to remove before the end of the cycle to remind the load. OFF LOUD you to remove the clothes. The signal NOTE: can be set at OFF (no sound), LOUD or ■ If items are removed before the end of anywhere in between. the cycle, turn the CYCLE SELECTOR
Resumen del contenido incluido en la página 8
Loading and using the dryer. Always follow the fabric manufacturer’s care label when laundering. Sorting and Loading Hints As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer. Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains. ® Bounce Fabric Conditioner Dryer Sheets have been approved for use in all GE Dryers when used in accordance with the manufacturer’s instructions. Do not overload. T
Resumen del contenido incluido en la página 9
Installation Spacemaker Dryer DCXH46, DSXH43D, DPXH46, DH43, PSXH43 Instructions If you have any questions, in the U.S., call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com. In Canada, call 1.800.561.3344 or visit our Website at: www.GEAppliances.ca FOR YOUR SAFETY: BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING � IMPORTANT – Save these � To reduce the risk of severe injury or death, follow all instructions for local inspector’s use. install
Resumen del contenido incluido en la página 10
Installation Instructions PREPARING THE INSTALLATION SITE TOOLS AND MATERIALS AND UNPACKING YOUR DRYER YOU WILL NEED 1. Prepare the area and exhaust for installation Phillips head screwdriver ❑ of the new dryer. Adjustable pliers (adjust leveling legs) ❑ 2. Check to be sure that the existing external Carpenter’s level ❑ exhaust is clean and that it meets attached installation specifications. Flat or straight blade screwdriver (may be needed ❑ for cord strain relief) 3. Place the four corner po
Resumen del contenido incluido en la página 11
Installation Instructions Read these instructions completely and carefully. ELECTRICAL CONNECTION ELECTRICAL CONNECTION INFORMATION FOR INFORMATION FOR GAS DRYERS ELECTRIC DRYERS WARNING – To reduce the risk of WARNING – To reduce the risk of fire, electric shock or personal injury: fire, electric shock or personal injury: � DO NOT USE AN EXTENSION CORD WITH � DO NOT USE AN EXTENSION CORD OR AN THIS APPLIANCE. ADAPTER PLUG WITH THIS APPLIANCE. � DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR � THIS
Resumen del contenido incluido en la página 12
Installation Instructions EXHAUST SYSTEM CHECKLIST WARNING � Never terminate the exhaust into a common duct HOOD OR WALL CAP with a kitchen exhaust system. A combination of � Terminate in a manner to prevent back drafts or entry grease and lint creates a potential fire hazard. of birds or other wildlife. � Do not use duct longer that specified in the exhaust � Termination should present minimal resistance to length table. Longer ducts can accumulate lint, the exhaust airflow and should require
Resumen del contenido incluido en la página 13
Installation Instructions EXHAUST DIRECTION CONNECTING THE DRYER TO All dryers are shipped set up for rear exhausting. HOUSE VENT (CONT.) On electric dryers, exhausting can be on the cabinet right or left side, or through the dryer bottom. Gas dryers can � Never install flexible metal duct in walls, ceilings, exhaust on the cabinet right side or the dryer bottom. To floors or other enclosed spaces. change exhaust direction you will need Exhaust Kit Pub. � Total length of flexible metal duct sh
Resumen del contenido incluido en la página 14
Installation Instructions LOCATION OF YOUR DRYER Allow the following clearances for ease of installation: Do Not Install the Dryer: FRONT SIDES REAR TOP 1.Do not install the dryer in an area exposed to dripping Alcove, stack, 3” (7.6 cm) 0 (0 cm) 3” (7.6 cm) 0 (0 cm) water or outside weather conditions. undercounter or closet 2.Do not install the dryer in an area where it will come in contact with curtains, drapes or anything that will THIS DRYER MUST BE EXHAUSTED OUTDOORS. obstruct the flow of
Resumen del contenido incluido en la página 15
Installation Instructions MOBILE HOME INSTALLATION ROUGH-IN DIMENSIONS 1. Dryer MUST be exhausted outside (outdoors, not 26 7/8″ beneath the mobile home) using metal ducting that will (68.3 cm) not support combustion. Metal ducting must be 4″ (10.16 cm) in diameter with no obstructions. Rigid metal duct is preferred. 2.If the dryer is exhausted through the floor, the exhaust Electrical connection system MUST NOT terminate beneath the mobile Under counter home. Termination MUST be securely fasten
Resumen del contenido incluido en la página 16
Installation Instructions ELECTRICAL INSTALLATION FOR GROUNDING REQUIREMENTS ELECTRIC DRYERS WARNING: Improper connection of the equipment-grounding conductor can result in a risk of WARNING: The following are specific electric shock. Check with a licensed electrician if you are in requirements for proper and safe electrical installation of doubt as to whether the appliance is properly grounded. your dryer. Failure to follow these instructions can create electrical shock and/or a fire hazard. Th
Resumen del contenido incluido en la página 17
Installation Instructions 3-WIRE SYSTEM FOR 4-WIRE SYSTEM FOR ELECTRIC DRYERS ELECTRIC DRYERS NOT for use in Canada. Effective January 1, 1996: The National Electrical Code DO NOT use for Mobile Home Installations. requires that new construction (non existing) utilize a NOT for use on new construction. 4-wire connection to an electric dryer. In Canada a 4-wire power supply cord is installed on 1. Remove the screws securing the terminal block access the dryer. cover and the strain relief mount
Resumen del contenido incluido en la página 18
Installation Instructions GAS CONNECTION FOR CAUTION: Before operating the dryer, make sure the dryer area is clear and free from GAS DRYERS combustible materials, gasoline, and other flammable 1. Remove the shipping cap from gas pipe at the rear of vapors. Also see that nothing (such as boxes, the dryer. clothing, etc.) obstructs the flow of combustion and ventilation air. Conversion to LP Gas: DO NOT connect the dryer to LP gas service without converting the gas valve. An LP 6. Run the drye
Resumen del contenido incluido en la página 19
Stacking Instructions MOUNTING THE DRYER TO WARNING: THE WASHER � To reduce the risk of electric shock, disconnect this appliance from the power supply before attempting The numbers in the illustration correspond to steps. any user maintenance. Turning the controls to the OFF position does not disconnect this appliance 1.Remove the washer top panel by first removing the 4 from the power supply. screws in the 2 brackets located on the top rear of the washer. � Refer to the washer and dryer ins
Resumen del contenido incluido en la página 20
Stacking Instructions–Reversing Door Swing 8. Insert the 2 long screws provided in the kit through The numbers in the illustration correspond to steps. the holes in the dryer front panel and install into the front mounting brackets. 5. Using the blade end of a putty knife covered with masking tape, carefully remove the hole plugs located 9. Install the hole plugs removed in step 5. in the bottom of the dryer front panel. 10. Refer to the washer and dryer installation instructions 6. Remove the 4
