Resumen del contenido incluido en la página 1
INSTRUCTION MANUAL
CD-ROM DRIVE
MODEL CDR-8130
IMPORTANT - Read all of these instructions carefully and understand
them before using your CD-ROM drive.
- Keep this instruction manual for future reference.
- If this CD-ROM drive changes ownership, be sure this
manual accompanies the CD-ROM drive.
CONTENTS
IMPORTANT SAFEGUARD--------------------------------------- 4
CONTROLS AND FUNCTIONS---------------------------------- 6
INSTALLATION ------------------------------------------------------ 7
Resumen del contenido incluido en la página 2
For USA Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that i
Resumen del contenido incluido en la página 3
CAUTION INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. VORSICHT UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET. NICHT IN DEN STRAHL BLICKEN AUCH NICHT MIT OPTISCHEN INSTRUMENTEN. ATTENTION RADIATION DU FAISCEAU LASÉR INVISIBLE EN CAS D'OUVERTURE EVITER TOUTE EXPOSITION AUX RAYONS. ADVARSEL USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER UDE AF FUNCTION. SE IKKE IND I STRÅLEN - HELLER IKKE MED OPTISKE INSTRUMENTER. ADVARSEL
Resumen del contenido incluido en la página 4
IMPORTANT SAFEGUARDS SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR EQUIPMENT READ ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS FOR LATER USE. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE PRODUCT. PRECAUTIONS FOR SAFETY Power source -This CD-ROM Drive should be operated from the type of power source indicated on the marked label. (+12V DC / +5V DC) To avoid the risk of electric short circuits or damage to your CD-ROM drive - Do not expose your CD-ROM Drive to rain or moisture. - Do not o
Resumen del contenido incluido en la página 5
- In a place where an operation temperature reaches beyond the specified temperature 40C - High humidity locations - In a location subject to extreme changes of temperature and humidity 3 - In a room where dust density higher than 0.1 mg/m - In a room that has air conditioning with humidity control which may scatter calcium combinations and other powdered substances - In a room containing exhaust gas fumes such as exhaust gas from gasoline or diesel engines or corrosive gas such as H S (Hydrogen
Resumen del contenido incluido en la página 6
CONTROLS AND FUNCTIONS Rear Panel Front Panel (6) (2) 39 1 40 2 (8) (9) (10) (3) (7) (4) (1) (5) (1) LOADING/UNLOADING/BUSY Indicator Indicator blinks green only when the Disc Tray is being opened or closed, or when the CD-ROM drive is accessing data. (2) Disc Tray When the power of the CD-ROM Drive is turned off, the Disc Tray can not be opened and closed. (3) Headphone Jack (3.5 mm) (4) Headphone Volume Control Adjust the headphone volume. (5) OPEN/CLOSE Button Press this button to open or clo
Resumen del contenido incluido en la página 7
6 4 2 Device is (Default setting) Master Circuit Board Device is OR 5 3 1 Slave Cable Select (9) ATAPI Interface Connector ATAPI bus connection (40 pin) (10) Power Supply Connector (DC Input) For connecting the power supply cable. 4 3 2 1 Circuit Board +12V GND +5V INSTALLATION WHAT YOU NEED HARDWARE - CD-ROM Drive - Interface card - Interface cable - Power supply cable - Mounting screws HARDWARE OPTION - Audio connecting cable - Sound Card SOFTWARE - CD-ROM device driver NOTE If
Resumen del contenido incluido en la página 8
Install the CD-ROM Drive following general installation procedure shown below. 1. Check the Device Configuration Jumper settings of the CD-ROM Drive such as Master, Slave, CSEL. (See page 6) 2. Turn off the host computer and unplug the power supply cable of the host computer. 3. Remove the host computer cover. 4. Install the CD-ROM Drive into the host computer and mount tightly by screws. 5. Check the settings of the interface card. 6. Install the interface card in the slot. 7. Firmly attach the
Resumen del contenido incluido en la página 9
120 mm Disc 80 mm Disc Disc label side Disc label side Disc Tray Disc Tray Push Push IMPORTANT - Do not press the OPEN/CLOSE button while the host computer is accessing the disc. It may caused an error. - When not using the CD-ROM Drive, keep the Disc Tray closed. It will prevent the entry of the dust and dirt, and reduce the requirements for disc and lens cleaning CAUTION If you do not observe the following items, troubles, such as that the Disc Tray can not be opened or can not be closed, ma
Resumen del contenido incluido en la página 10
CAUTION Do not use a breakable bar. A broken bar inside the CD-ROM Drive may cause a malfunction. Eject bar Push Minimum straight length = 30 mm Diameter = 1 - 1.8 mm Lens Cleaning A commercially available "Laser Lens Cleaning Disc" may be used to clean up the pick-up lens of the CD-ROM Drive. Use the Compact Disc Laser Lens Cleaner LLC-1. (by AUDIO SOURCE in U.S.A., by AKUSTIK SISTEME VERTRIEBS GHBH in GERMANY and by SAEC COMMERCE CO.,LTD. in JAPAN.) (1) Turn on the CD-ROM Drive. (2) Using t
Resumen del contenido incluido en la página 11
Symptoms Possible causes Remedy The CD-ROM 1.You place the disc up-side 1.Place the disc right side up in the Drive does not down in the Disc Tray. Disc Tray, then load it. operate even when 2. The disc is dirty. 2.Clean the disc surface.(See page 4) a disc is loaded. 3. The pick-up lens is 3.Clean up the pick-up lens.(See page dirty. 10) 4.Change the disc. 4.The disc is scratched or warped. 5.Turn off your SYSTEM and re- 5.Cable connection is connect cables correctly. incorrect. The Disc Tray c
Resumen del contenido incluido en la página 12
SPECIFICATIONS GENERAL Power Requirements DC Voltage +12V ±10% 1.0A +5V ±5% 0.7A Ripple +12V 300 mVpp (maximum) +5V 150 mVpp (maximum) Dimensions ( W x H x D ) 146 x 41.3 x 190 mm (Excluding front panel) Front panel : 149.3 x 42.7 x 5 mm Mass 0.95 kg Operating & Storage Conditions Temperature 5 - 45 °C (operating) -30 - 60 °C (non-operating) Relative humidity 15 - 85% RH (operating) (non-condensing) 10 - 90% RH (non-operating) (non-condensing) PERFORMANCE Disc Diameter 120 mm, 80 mm -1 Rotationa
Resumen del contenido incluido en la página 13
13
