Resumen del contenido incluido en la página 1
MODEL G0656
8" JOINTER w/BUILT-IN
MOBILE BASE
OWNER'S MANUAL
COPYRIGHT © NOVEMBER, 2007 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL10198 PRINTED IN CHINA
Resumen del contenido incluido en la página 2
����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ������������������������������������������������������������������ �������������������������������������������������������������������� ���������������������������������������������������������������
Resumen del contenido incluido en la página 3
Table of Contents INTRODUCTION ............................................... 2 Basic Controls .............................................. 20 Foreword ........................................................ 2 Stock Inspection & Requirements ............... 21 Contact Info ................................................... 2 Squaring Stock ............................................ 22 Machine Data Sheet ...................................... 3 Surface Planing .............................
Resumen del contenido incluido en la página 4
INTRODUCTION Foreword Contact Info If you have any comments regarding this manual, We are proud to offer the Model G0656 8" Jointer please write to us at the address below: with Built-In Mobile Base. This machine is part of a growing Grizzly family of fine woodworking Grizzly Industrial, Inc. machinery. When used according to the guide- C /O Technical Documentation Manager lines set forth in this manual, you can expect P.O. Box 2069 years of trouble-free, enjoyable operation and Bellingham
Resumen del contenido incluido en la página 5
Machine Data Sheet � � � � � � �� � � � �� � � � � � � � �� � � � �� �� � � � � �� � �� � � � � �� � � � � � � � �� �� � �� � � � � �� � � � � �� � � � � �� � � � � � � � �� �� � � �� � �� � � � � �� � � � � � � � � ������ ����� ��� �������� ��� ������� ���� �������� ����������� ������� ��������������������������������������������������������������� � ������������������������������������������������������������������������������������������������������������ ���� ���� � � �������������������� �
Resumen del contenido incluido en la página 6
�������� ���������� ������ ��������� ����������������������������������������������������������������������������������������������������������������������������������� ����� �� ������ ��� ���� �������� ������ ��� ��� ��������������������������������������������������������������� � ����������������������������������������������������������������������������������� �� � �������� ������ ��� ���� ������������������������������������������������������������������������������������������������������
Resumen del contenido incluido en la página 7
Identification E D H B F A D E C G I J K Q M P N O L Figure 1. Model G0656 identification. A. Outfeed Table B. Fence C. Cutterhead Guard D. Fence Adjustment Wheel E. Fence Tilt Handle F. ON/OFF Switch G. Infeed Table H. Fence Tilt Lock I. Outfeed Table Lock J. Fence Lock K. Depth Stop Lever L. Infeed Table Lock M. Infeed Table Handwheel N. Depth Scale O. Wheel Assembly P. Dust Port Q. Outfeed Table Handwheel -5- G0656 8" Jointer with Built-In Mobile Base
Resumen del contenido incluido en la página 8
� � � �� � �� � �� � � � �� � � � �� � � � �� � � �� � � � � � � �� � � � �� � � � � � � �� � � �� � � � � � �� � � � � ��� � � � � � � � � �� � � � �� � � � � � � � � � �� � � � � � � �� � �� � � � � � �� � � � � � � �� � �� � �� � � � � � � �� � �� �� � � � � � � � � �� � �� � � � � � � � �� � � � � � � ���� � � � � �� � � � � �� � � � �� � � � � � �� �� � �� �� � � � � � �� � �� � � � � � � �� � � �� � � � � � �� � � � � �� � � � � � � � �� � �� � � � � � �� � � �� � � � � �� � �� � � � � � �
Resumen del contenido incluido en la página 9
� � � � � �� � � � � � � �� � � � �� � � �� � � � � � � � � � ��� ����� ������ �������� ���� ���� � ���� � � � � � � � � � � � � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � � � � � � � � � � � � � � �� ���������� ����� �� ������ ��� ��������� ���� � � � � � � � � � � � � � � � � � � � � � � � � � � � �� � ����� ���� ���������� ��������� ������� ���� � ���������� ������������� ���� ����� ���� �������� ���� ���������� �� � ����������� ���� � � � � � � � � � � � � � � � � � � � � � � �
Resumen del contenido incluido en la página 10
Additional Safety Instructions for Jointers 1. JOINTER KICKBACK. "Kickback" is when 7. MAXIMUM CUTTING DEPTH. The maxi- 1 the workpiece is thrown off the jointer table mum cutting depth for one pass is ⁄8". by the force of the cutterhead. Always use To minimize kickback, never attempt any push blocks and safety glasses to reduce single cut deeper than this! the likelihood of injury from “kickback.” If you do not understand what kickback is, or how 8. JOINTING WITH THE GRAIN. Jointing i
Resumen del contenido incluido en la página 11
SECTION 2: CIRCUIT REQUIREMENTS Power Connection Device 220V Operation The type of plug required to connect your machine to power depends on the type of service you cur- rently have or plan to install. We recommend using the plug shown in Figure 2. Serious personal injury could occur if you connect the machine to power before com- pleting the setup process. DO NOT connect the machine to the power until instructed later in this manual. Electrocution or fire could result if machine is not g
Resumen del contenido incluido en la página 12
SECTION 3: SETUP Setup Safety Items Needed for Setup The following items are needed to complete the This machine presents setup process, but are not included with your serious injury hazards machine: to untrained users. Read through this entire manu- Description Qty al to become familiar with • Safety Glasses (for each person) .............. 1 the controls and opera- • Wrench or Socket 17mm ............................ 2 tions before starting the • Wrench or Socket 13mm .................
Resumen del contenido incluido en la página 13
Inventory The following is a description of the main compo- A nents shipped with your machine. Lay the compo- nents out to inventory them. H B Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully. Occasionally C we pre-install certain components for shipping G purposes. D F E Wood Crate: (Figure 3) Qty Figure 3. Box 1 inventory contents. A. Jointer Assembly ........................................ 1 B. Cutterhe
Resumen del contenido incluido en la página 14
Hardware Recognition Chart -12- G0656 8" Jointer with Built-In Mobile Base
Resumen del contenido incluido en la página 15
Clean Up Site Considerations The unpainted surfaces are coated with a waxy Floor Load oil to prevent corrosion during shipment. Remove Refer to the Machine Data Sheet for the weight this protective coating with a solvent cleaner or and footprint specifications of your machine. citrus-based degreaser such as Grizzly’s G7895 Some residential floors may require additional Citrus Degreaser. To clean thoroughly, some parts reinforcement to support both the machine and must be removed. For op
Resumen del contenido incluido en la página 16
5. With the help of an assistant, lift the jointer Assembly onto the stand. 6. Align the mounting holes on the jointer and To assemble the jointer: stand. 1. Carefully lay the stand on its side so you can 7. Secure the jointer to the stand with the M8- access the underside. 1.25 x 50 cap screws, washers, and hex nuts, as shown in Figure 8. 2. Bolt the wheel assembly to the stand with the provided hardware, as shown in Figure 7. Note: Refer to the Inventory List on Page 11 for a list of co
Resumen del contenido incluido en la página 17
9. Slide the motor upward, and place the V-belt 13. Shift the motor horizontally as needed to around the cutterhead pulley and the motor align the motor pulley with the cutterhead pul- pulley. ley, then replace the V-belt. 10. Slide the motor down to rest on the V-belt. 14. Tighten the motor mount fasteners. 11. Place a straightedge against both pulleys 15. Secure the infeed and outfeed handwheels (Figure 10) and check the alignment of with the cap screws and flat washers already the two pull
Resumen del contenido incluido en la página 18
19. Using a 2.5mm hex wrench, thread the set screw through the hole in the forked end of the cutterhead guard shaft (Figure 14). Note: Thread the set screw far enough to prevent the guard from being pulled out. Figure 15. Attaching pedestal switch to stand. 24. Thread the excess switch cord through the access hole in the stand and connect it to the motor cord. 25. Assemble the knife setting gauge using the knife setting gauge rod, feet and 8mm e- Figure 14. Example of installing cutterhea
Resumen del contenido incluido en la página 19
Dust Collection Setting Outfeed Table Height The outfeed table height MUST be level with the DO NOT operate the Model G0656 without an knives when they are at top-dead-center. If the adequate dust collection system. This jointer outfeed table is set too low, the workpiece will be creates substantial amounts of wood dust tapered from front to back. If the outfeed table while operating. Failure to use a dust collec- is set too high, the workpiece will hit the edge of tion system can resul
Resumen del contenido incluido en la página 20
—If your outfeed table is correctly set, no Recommended adjustments are necessary. Adjustments —If the knife lifts the straightedge off the table or the table is below the straight- edge, adjust the outfeed table height with For your convenience, the adjustments listed the handwheel until the straightedge just below have been performed at the factory and touches a knife at its highest point of rota- no further setup is required to operate your tion. machine. 5. Lock the outfeed table,