Resumen del contenido incluido en la página 1
Homeowners Guide
Bath Whirlpool
K-812-N1
M product numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de M corresponden a México
(Ej. K-12345M)
Français, page “Français-1”
Español, página “Español-1”
1019490-5-C
Resumen del contenido incluido en la página 2
Important Information INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING: When using electrical products, basic precautions should always be followed, including the following: DANGER: Risk of personal injury. To reduce the risk of injury, do not permit children to use this unit unless they are closely supervised at all times. WARNING: Risk of personal injury. To avoid injury, exercise care when enteri
Resumen del contenido incluido en la página 3
Important Information (cont.) electric shock. Do not use this whirlpool bath. Disconnect the whirlpool and have the problem corrected by a qualified service representative before using. Flush your whirlpool system twice a month or more depending upon usage, as described in the ″Flush System″ section of this guide. Repeated use of personal care products containing oils can damage plastic whirlpool components. Do not use heavy, vegetable-based shampoos or bath oils. Whirlpool hydro-massage action c
Resumen del contenido incluido en la página 4
Flexjet Flow Mode Indicator Bar - Shows waterflow volume or pulse speed Activates Mode Selected Increases Flow or Pulse Backjet Mode-Adjust Pulse Rotate outer ring to Neckjet Mode-Adjust Pulse access desired mode. Decreases Flow or Pulse Power On/Off Heater Lighted User Keypad User Keypad NOTE: The illustration of the user keypad differs slightly from the user keypad equipped with your model. The Backjet Mode is not equipped with your model. Available modes will be illuminated in blue. Active
Resumen del contenido incluido en la página 5
Fill with water at least 2" (5.1 cm) above the highest jet. Turn the jet trim ring clockwise to Position the jet decrease the flow. nozzles to direct the water flow as desired. Turn the jet trim ring counterclockwise to increase the flow. Operation NOTE: If the whirlpool is not operating properly, consult the ″Troubleshooting″ section of this guide before calling a qualified service representative. Turn the jet trim fully counterclockwise. Position the jet nozzles so they face down toward
Resumen del contenido incluido en la página 6
Operation (cont.) NOTE: To activate or deactivate functions while the neckjets are operating, rotate the outer ring until the desired function is flashing and press ″OK.″ Care and Cleaning For best results, keep the following in mind when caring for your KOHLER product: • Always test your cleaning solution on an inconspicuous area before applying to the entire surface. • Wipe surfaces clean and rinse completely with water immediately after applying cleaner. Rinse and dry any overspray that lands
Resumen del contenido incluido en la página 7
Warranty (cont.) This is Kohler Co.’s exclusive written warranty. Warranty Kohler Co. warrants the cast iron components of products manufactured after February 10, 2000, to be free of defects in material and workmanship during normal residential use for as long as the original consumer purchaser owns his or her home. Gloss reduction, scratching, staining and alkaline etching of the finish over time due to use, cleaning practices or water or atmospheric conditions, are not manufacturing defects bu
Resumen del contenido incluido en la página 8
Warranty (cont.) 5. It is recommended that the consumer save the invoice or receipt as additional protection, as it may substitute the warranty in the case that there is a discrepancy in the validity of the warranty. EXCEPTIONS AND RESTRICTIONS The Warranty will not be valid in the following cases: 1. When the product is not operated in accordance with the instructions concerning use and operation set forth in the owner’s manual or installation instructions, and when the recommendations and warn
Resumen del contenido incluido en la página 9
Remove the Jets Reinstall the Jets Insert the tool hook as shown and pull the jet out of the housing. The jet should be facing up when this is done. Housing Inspect and lubricate the O-ring. Slide the O-ring onto the first shoulder of the jet. Insert the jet into the housing, and lightly push and rotate until it snaps in position. Troubleshooting NOTICE: This section is for general aid only. A Kohler Authorized Service Representative or qualified electrician should correct any electrical pro
Resumen del contenido incluido en la página 10
Troubleshooting (cont.) Symptoms Probable Causes Recommended Action 3. User keypad is A. Control program is locked. A. Reset GFCI or RCD. illuminated, but does B. Wiring harness from user B. Check wiring for proper connections. not respond to keypad to control is loose, Replace wiring harness if necessary. buttons or outer ring. disconnected or damaged. C. User keypad does not work. C. Replace user keypad. D. Control does not work. D. Replace control. 4. User keypad A. Control program is locked.
Resumen del contenido incluido en la página 11
Troubleshooting (cont.) Symptoms Probable Causes Recommended Action 1. Remote control does not A. Batteries improperly installed or A. Replace batteries. work. dead. B. Antenna on wiring harness is B. Replace wiring harness. damaged. C. Remote control not programmed C. See homeowners guide or service correctly. manual. D. Remote control does not work. D. Replace remote control. E. Control does not work. E. Replace control. Backjet System Symptoms Probable Causes Recommended Action 1. Backjets do
Resumen del contenido incluido en la página 12
Troubleshooting (cont.) Symptoms Probable Causes Recommended Action 3. Pump operates but A. Neckjet line is blocked. A. Disconnect neckjet hoses and neckjets do not turn on. remove blockage. Indicator bar on user B. Wiring harness from neckjet to B. Check wiring for proper keypad is NOT flashing. control is loose, disconnected or connections. Replace wiring damaged. harness if necessary. C. Butterfly valve does not work. C. Replace butterfly valve. D. Control does not work. D. Replace control. 4. W
Resumen del contenido incluido en la página 13
*Note: All tubing 1" unless otherwise noted. 1-1/2" Tubing 94268 Reducer In-line Heater 1015007 Wire Harness **Finish/color code must be specified when ordering. Service Parts Kohler Co. 13 1019490-5-C
Resumen del contenido incluido en la página 14
94496 (Curved) 94726-A (White) 94497 (Flat) 94726-B (Black) Pillow Kit Cover 1019439 93931 Sensor Screw 93511** 94377 (Curved) Cover 94495 (Flat) Pillow 93823 Nut Cast Iron Shell Neck 93590-A Valve Hardware Manifold 94387-A [6" (15.2 cm)] 90153 93542 94387-B [4-3/8" (11.1 cm)] Locknut 93848 Gasket Plate Elbow 64212 63270 Washer Washer 1000054 Screw 60170 60982 Nut 93948-A1 [8-3/8" (21.3 cm)] Screw 93948-B1 [9-7/8" (25.1 cm)] 91820 93948-C1 [6-7/8" (17.5 cm)] Sleeve 93948-D1 [6" (15.2 cm)] 9394
Resumen del contenido incluido en la página 15
1003065 Suction Flange 73518 Removal Tool Plug 93685 Housing 96708 Flange 65886 (Acrylic and FRP) 60050 (Cast Iron) 65054** Gasket Screw 96895** (Colored Finishes) 65061**(Metal Finishes) Cover 65226** Suction Cover Plug 93836 (1/2") 93837 (3/4") 93838 (1") 93839 (1-1/4") 94853 (1-1/2") Tube (w/Couplings) 91967 Check Valve 1086350 67665 Flange Removal Wrench Plug 67429 Flange 67889 Jet Housing 65885 (Acrylic and FRP) 67668 (Cast Iron) Gasket 34353 O-Ring Single Jet For Whirlpools With 5 or Less
Resumen del contenido incluido en la página 16
61776 1018964 1033678 Lock Washer 60320 67065 Bracket Screw Screw Ground Lug 90153 Locknut 61776 93892-A Lock Washer Electrical Box 67065 Ground Lug 60320 Screw 1080774 61845-K Union Assy 94821 Copper Grounding Wire O-Ring 93003 1019432 Strain Relief Carriage Bolt 93893 1080775 94821 Cover Pump Tee O-Ring To Tee Heater 90154 Locknut 1016957 Pump 1016958 Motor 1010673 Seal 1010548 Volute 1010676 1019445-A [1-3/4" (4.4 cm)] Cover 1019445-B [2-3/4" (7 cm)] 1010677 1019445-C [3" (7.6 cm)] 1016960 Sc
Resumen del contenido incluido en la página 17
1022408 1012653 In-line Heater Adapter 1032545 Housing 1012916 94821 Nut w/Screws O-Ring 1011679 94821 Gasket O-Ring 1012653 Adapter 1012977 Adapter 1018710 Tee Heater 94821 1012916 O-Ring Nut with Screws 94821 O-Ring 1012977 Adapter 1011679 Gasket **Finish/color code must be specified when ordering. Kohler Co. 17 1019490-5-C
Resumen del contenido incluido en la página 18
1020677 Gasket 1023381 Wrench 65157 Nut 1013453 Spring 1013452** Dial Trim 1013499 Housing Carefully study decal and cover detail below for proper service part identification. 91639 O-Ring 1020678-A 1020678-B Cover/Circuit Board Cover/Circuit Board (w/Wrench) (w/Wrench) 91639 91639 O-Ring O-Ring 1013497-A 1013497-B Decal Decal 1020678-C 1020678-D Cover/Circuit Board Cover/Circuit Board (w/Wrench) (w/Wrench) 91639 91639 O-Ring O-Ring 1013497-C 1013497-D Decal Decal 1020678-E 1020678-M Cover/
Resumen del contenido incluido en la página 19
Guide du propriétaire Baignoire à hydromassage Informations importantes INSTRUCTIONS RELATIVES AUX RISQUES D’INCENDIE, D’ÉLECTROCUTION OU DE BLESSURES CORPORELLES LIRE ET SUIVRE TOUTES LES INSTRUCTIONS CONSERVER CES INSTRUCTIONS AVERTISSEMENT : Lors de l’utilisation des produits électriques, des précautions de base doivent toujours être observées, incluant ce qui suit : DANGER : Risque de blessures corporelles. Afin de réduire les risques de blessures, ne jamais permettre à un enfant d’utiliser c
Resumen del contenido incluido en la página 20
Informations importantes (cont.) Utiliser cette baignoire à hydromassage uniquement pour un usage tel que décrit dans ce guide. Ne pas utiliser des fixations non recommandées par le fabricant. Ne jamais faire tomber ou insérer d’objet quelconque dans les ouvertures. Ne pas laisser de petits objets tels que des jouets ou accessoires pour le bain dans la baignoire à hydromassage lorsqu’elle est en marche. Ne pas utiliser cet appareil sans ses protecteurs (couvercles) sur ses raccords d’aspiration.
