Resumen del contenido incluido en la página 1
Responder LE Model 5701
Security and Remote Start
Owner’s Guide
© 2008 Directed Electronics, Vista, CA
Resumen del contenido incluido en la página 2
Limited lifetime consumer warranty Directed Electronics. (“Directed”) promises to the original purchaser to repair or replace (at Directed’s election) with a comparable reconditioned model any Directed unit (hereafter the “unit”), excluding with- out limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the
Resumen del contenido incluido en la página 3
CABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE UNIT. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGE TO VEHICLE, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE
Resumen del contenido incluido en la página 4
Government Regulations This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) This device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection aga
Resumen del contenido incluido en la página 5
Table of contents Limited lifetime consumer warranty . . . . . . . . . . . . . . .i . i . . . . . Government Regulations . . . . . . . . . . . . . . . . . . . . .i . v . . . . . . . . What is included . . . . . . . . . . . . . . . . . . . . . . . .1 . . . . . . . . . . . Important information . . . . . . . . . . . . . . . . . . . . .1 . . . . . . . . . . Your warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Replacement remotes . . . . . . . . . . . . . . . . . .
Resumen del contenido incluido en la página 6
Points to remember . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Runtime Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Manual transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Timer mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Turbo timer mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Cabin temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Safety fe
Resumen del contenido incluido en la página 7
What is included ■ The control module with Stinger™DoubleGuard®two-stage shock sensor ■ Control center (installed out of sight on your vehicle) with integrated status LED and Valet override switch ■ One five-button/2-way Supercode Responder LE Remote Control ■ One five-button/ 1-way Supercode remote ■ Revenger™Soft Chirp™six-tone siren ■ A shut-down toggle switch ■ Window decals ■ Your warranty registration �� Important information Congratulations on the purchase of your state
Resumen del contenido incluido en la página 8
Your warranty Your warranty registration must be completely filled out and re- turned within 10 days of purchase. Your product warranty will not be validated if your warranty registration is not returned. Make sure you receive the warranty registration from your dealer. It is also necessary to keep your proof of purchase, which reflects that the product was installed by an authorized dealer. Replacement remotes Your system comes with one Responder LE remote control (P/N 7251V) and one compa
Resumen del contenido incluido en la página 9
Responder LE 2-Way 8 1 3 9 4 2 5 A U X 6 7 Description Feature 1 Transmit indicator LED indicators Blinks indicate function confirmation 2 Lock button Press for one second to arm. 3 Unlock button Press for one second to disarm. 4 5 Remote start Press for one second to activate remote button start. 6 Auxiliary Press and hold for 1.5 second to activate button optional trunk release. 7 Function Allows access to programming and modi- button fies operation of the other buttons. 8 2 WAY Label Back
Resumen del contenido incluido en la página 10
Responder LE 1-way 7 1 2 8 3 4 A U X 5 6 Feature Description Transmit indicator 1 Lock button Press for one second to arm. 2 Unlock button Press for one second to disarm. 3 4 Remote start Press for one second to activate remote button start. 5 Auxiliary Press and hold for 1.5 second to activate button trunk release. 6 Function Allows access to programming and button modifies operation of the other buttons. 7 1 WAY Label Back of remote has label to identify the remote as 2-way or 1-way 1 8
Resumen del contenido incluido en la página 11
Transmitter configuration REMOTE CONTROL FUNCTIONS TABLE Level x 0 x 1 x 2 x 3 x 4 Button ARMED ARMED SILENT SENSOR ARM (SILENT (SILENT ARM BYPASS SENSOR) TRIGGER) LOCK SILENT DISARM VALET MODE CAR FINDER — DISARM UNLOCK REMOTE RUNTIME REAR TIMER MODE SMART START START RESET DEFOGGER REMOTE START TRUNK AUX 1 AUX 2 AUX 3 — RELEASE AUX CABIN LAST RUNTIME FUNCTION TEMPERATURE ARM STATUS TRIGGER CHECK SHIFT REQUEST (2-way Only) REQUEST (2-way Only) (2-way Only) (2-way Only) F
Resumen del contenido incluido en la página 12
Feature Command Confirmation Notes Feedback Silent Arm Arm/Lock LED Arms the system without Press one- time on, no audio chirps and then press . 1 Disarm/Lock Disarms the system without Silent Disarm 2 Press one- time LED on, no chirps and then press audio . 3 Runtime Remote start Re-starts the remote start reset Press one-time ON tones. runtime counter if remote start 4 and then . is active. Note: If remote A U X start is not active, the 2-WAY 5 remote will respond with error
Resumen del contenido incluido en la página 13
Feature Command Confirmation Notes Feedback 1 Valet Mode UnLock LED on To enter or exit Valet mode, 2 Press two- and beeps 1 or even if Armed. times and then 2 times When entering Valet Mode the . 3 unlock LED blinks, and the remote beeps one time. When exiting Valet Mode the unlock 4 LED blinks and the remote beeps two-times. A U X 5 Remote start Enables or disables the remote Timer mode Press two- LED on. start timer mode. 6 times and then . Aux 2 The AUX LED This is an optiona
Resumen del contenido incluido en la página 14
Feature Command Confirmation Notes Feedback Armed LED on, 1 beep Arms the system; sensor Full Press three- (Silent & 3 error tone Trigger will ONLY page the times and then . Sensor mode) remote and will not activate the siren/lights. Wired inputs will page and activate the siren/lights. 1 On Remote Arm/Disarm cancels the light Car Finder 2 Press three- Control: flashes. times and then Unlock LED on . 3 with 1 short beep 4 On Vehicle: 1 long siren A U X 5 chirp and park- ing light
Resumen del contenido incluido en la página 15
Feature Command Confirmation Notes Feedback Armed Lock LED on, 1 Arms the system; sensor and Press four- (Silent beep & 4 error hardwire Full Triggers will ONLY times and then . Trigger tone page the remote and will not mode) activate the siren/lights. For more details see Silent Mode 2 section on page 25. Remote start Automatically turns on during Rear Defogger Press four LED ON, 1 remote start. times, and then beep. . (Only after remote start is on.) Last Trigger Replays the T
Resumen del contenido incluido en la página 16
System maintenance The system requires no specific maintenance. Your remotes are pow- ered by small coin cell lightweight 3-volt lithium batteries that will last approximately one year under normal use. The 2-way remote uses two CR2016 cell batteries and the 1-way remote uses one CR2032 cell battery. When the battery begins to weaken, the oper- ating range will be reduced. Low battery indicator When the batteries are low on the 2-way remote it will emit two groups of beeps, the LED will fl
Resumen del contenido incluido en la página 17
Remote control programming The Responder LE 2 way remote control has menus for programming the remote to the system control module including adjusting the control module onboard shock sensor, and for configuring the remote control user features. To program the remote user features: 1 1. Press and hold the button for 12 seconds: (at 3 seconds ignore the Car number indicator.) 2 2. The remote emits one long beep, and the Transmit LED turns on. This indicates the Main menu. 3. Press and hold
Resumen del contenido incluido en la página 18
1 2 button: Remote Beeps 3 ▀ Disarm LED OFF: The remote will not emit beeps except when pro- 4 gramming. A U X ▀ Disarm LED ON: The remote will emit beeps normally. 5 ▀ Disarm LED blinking: The remote will emit beeps only for alarm trigger messages from the alarm system. 6 button: Runtime Low Alert feature Note: This feature is not available on the 1-way remote. ▀ Remote Start LED OFF: The remote will ignore Runtime Low Alert messages. ▀ Remote Start LED ON: The remote will emit fe
Resumen del contenido incluido en la página 19
Multi-car control capability You can operate the Responder LE 2-way remote control system for two cars, with full command capability for both vehicles. While holding a command button and transmitting, the Amber LED at the top of the remote control will blink in groups to indicate which Car is being controlled. ▀ Car 1: 1 blink ▀ Car 2: 2 blinks 1 To change the Car to be operated: 2 Press/hold the button for 3 seconds or until the remote beeps and the and/or LEDs turn on. This will ind
Resumen del contenido incluido en la página 20
adjust mode: ▀ Press/hold the button of the remote control for 8 seconds or until the Amber LED turns on and you hear one long beep. ▀ Press/hold the button 1.5 seconds or until the amber led flashes once: The control module will emit one long chirp, enter adjust mode, and send the current level of information back to the transmitter. The remote will beep once and the button LEDs will turn on to indicate the current level. Press the Arm, Disarm, or Remote Start buttons to adjust the
