Resumen del contenido incluido en la página 1
WARNING
YJ USA Corp., 3970 Lindbergh Drive Adison, TX 75001 www.jumppod.com
877-928-8777
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
3
Resumen del contenido incluido en la página 4
1. The owner and supervisors of the trampoline 13. Do not allow more than one person on the trampoline are responsible to make sure all the users are and inside the trampoline enclosure. Use by more than aware of practices specified in this manual. one person at the same time can result in serious injuries. 2. Trained Spotter supervision is recommended. 14. Misuse and abuse of the trampoline is dangerous and 3. Place the trampoline and trampoline enclosure
Resumen del contenido incluido en la página 5
25. Do not attach anything to the barrier that is not a 35. While keeping the head erect, focus eyes on the trampoline manufacturer approved accessory or part of the toward the perimeter. This will help control bounce. enclosure system. 36. Read all instructions before using the trampoline enclosure 26. Wear clothing free of drawstrings, hooks, loops, or and trampoline. Warnings and instructions for the care, anything that could get caught in the barrier.
Resumen del contenido incluido en la página 6
Note: The 6
Resumen del contenido incluido en la página 7
Resumen del contenido incluido en la página 8
Resumen del contenido incluido en la página 9
Resumen del contenido incluido en la página 10
Resumen del contenido incluido en la página 11
the sharply spot.
Resumen del contenido incluido en la página 12
Resumen del contenido incluido en la página 13
Resumen del contenido incluido en la página 14
14
Resumen del contenido incluido en la página 15
1. Make sure you understand the information in 1 the box at the top of this page before you begin assembling the trampoline. Lay three Top Tubes (1), (2) and (3) on the ground as shown. Make sure there is a T-connector(4) on Top Tube Center (1, A marking with bigger end), Socket(7) on the Top 6 Tube(2, B marking with bigger end) and T-connector(4) on 12 5 the Top Tube(3, c marking with bigger end). 12 Insert Top Tube(1, A marking with small end) into Socket(7). Then insert Top Tube(1, 2) into
Resumen del contenido incluido en la página 16
3. Lay the Bed (8) on the ground inside of the Frame 8 assembled frame. Make sure that the two warn- V-rings ing decals (not shown) are on top of the Bed. 10 Note: There are V-rings around the edge of the 10 Bed (8) and holes around the top of the frame. 10 10 During this step, you will attach the Bed to the frame using the included Springs (10) for holes on top of frame and for holes on bottom of frame (see the inset drawing). Hook a spring to the Holes Bed(8) and using the spring pulling to
Resumen del contenido incluido en la página 17
4 4. Lay the Frame Pad (9) on the frame. Do not use the trampoline without the Frame Pad (9), which is designed to reduce the likelihood of injury to the user from coming in con- Webbing tact with the trampoline frame. If you do not have a Frame Pad, call our Customer Hot Line toll-free at 877-927-8777, Monday-Friday,8 a.m. -5 p.m. Central Time.(Excluding Holidays) Safety pad Properly install the Frame Pad before using the D-ring trampoline. Webbing T-connector 5 5. Look under the trampolin
Resumen del contenido incluido en la página 18
6 6. Using the included plastic tie, attach the Safety Placard (11) to the frame near the point where jumpers will climb onto and off the trampoline. The trampoline is now fully assembled. Make sure that all parts are securely attached. Familiarize yourself and all users of the tram- Frame poline with the safety precautions, use and instructional materials, and care and mainte- nance instructions in this manual before using the trampoline. 7. Loosen the straps (not shown) on the underside of t
Resumen del contenido incluido en la página 19
10 10. Attach the other three Pole(16,17) in the same way. See inset drawing. 11. Lay out Top G3 Pole (18), joint each section Connector to a straight line as shown. Assemble the remaining Top G3 Pole (18) in the same way. Spread the Netting (20) on the trampoline bed, insert a Top G3 Pole (18) into the opening of Top Sleeve on the Netting (20). Insert the other Top G3 Pole (18) into the opposite opening of Top Sleeve on the Netting (20).
Resumen del contenido incluido en la página 20
Attach the first hanging point at the upper edge of the Netting (20) with the G3 Pole (18) to the Hemisphere Cap (19) of Top enclosure pole(17). Attach a second hanging point directly across the Netting (20) from the first hanging point. Attach the other two hanging point halfway between the first two hanging points, so four hanging points are attached as shown. See insert drawing for attached of G3 Pole (18): Hemi
