Resumen del contenido incluido en la página 1
NOTE:
Please read all instructions
®
carefully before using this
product Gym Dandy
Table of Contents
TEETER TOTTER
Safety Notice
TT-320
Hardware Pack
Assembly Instruction
Parts List
Operation Tips
Warranty
Ordering Parts
Model
TT-320
Retain This
Manual for
Reference
10-12-07
®
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
OWNER'S
Tel: (800) 999-8899 Fax: (626) 961-9966
MANUAL
www.impex-fitness.com
inf
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICE..................................................................... 3 HARDWARE PACK……......…....................................................................... 5 ASSEMBLY INSTRUCTIONS........................................................................... 6 EXPLODED DIAGRAM............................................................
Resumen del contenido incluido en la página 3
2
Resumen del contenido incluido en la página 4
IMPORTANT SAFETY NOTICE This play ground equipment is built for optimum safety. However, certain precautions apply whenever you operate a piece of play ground equipment. Be sure to read the entire manual before you assemble or operate your equipment. In particular, note the following safety precautions to reduce the likelihood of serious or fatal injury. 1. Children must be supervised at all times and never left unattended with the unit. 2. Do not install the equipment over concre
Resumen del contenido incluido en la página 5
CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS The U.S. Consumer Product Safety Commission (CPSC) estimates that about 100,000 playground equipment- related injuries resulting from falls to the ground surface are treated annually in U.S. hospital emergency rooms. Injuries involving this hazard pattern tend to be among the most serious of all playground injuries, and have the potential to be fatal, particularly when the injury is to the head. The surface under and around pla
Resumen del contenido incluido en la página 6
HARDWARE PACK 5
Resumen del contenido incluido en la página 7
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrench. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. Caution: Children must NOT use the equipment until it’s properly installed. STEP 1 (See Diagram 1) A.) Place the two Base Stabilizers (#2) on a flat surface. Attach one end of a Main Frame (#1) to a Base Stabilizer from the top. Attach one end of Cross Brace (#3) to the Base Stab
Resumen del contenido incluido en la página 8
STEP 2 (See Diagram 2) A.) Attach the Pivot on a Swing Arm (#6) to the open bracket on the Swing Base (#7). Align the holes and insert an Axle (#12) through the holes. Secure each end of the Axle with one Bushing (#13), Ø ¾” Washer (#27), and M10 x 5/8” Allen Bolt (#23). B.) Repeat the Procedure A above to install the other Swing Arm. DIAGRAM 2 7
Resumen del contenido incluido en la página 9
Step 3 (See Diagram 3) A.) Connect the Left Seat Support (#5) and the Right Seat Support (#4). Secure them together with two M10 x 3” Hex Bolts (#21), four Ø ¾” Bent Washers (#26), and two M10 Aircraft Nuts (#28). B.) Cover the two Nuts with two Nut Covers (#16). DIAGRAM 3 8
Resumen del contenido incluido en la página 10
Step 4 (See Diagram 4) A.) Note: Help of another person is strongly recommended for this step. B.) Attach the two open brackets on the Right and Left Seat Supports (#4 & #5) to the pivot on the two Swing Arms (#6). C.) Insert an Axle (#12) through the holes. Secure each end of Axle with one M10 x 5/8” Allen Bolt (#23), Ø ¾” Washer (#27), and Bushing (#13). DIAGRAM 4 9
Resumen del contenido incluido en la página 11
STEP 5 (See Diagram 5) A.) Place a Seat Pad (#8) onto the Left Seat Support (#5). Secure the front hole on the Left Seat Support with one M10 x 3 3/8” Allen Bolt (#25), Ø ¾” Lock Washer (#29), and Ø ¾” Bent Washer (#26). Secure the rear hole with one M10 x 4 1/8” Allen Bolt (#24), Ø ¾” Lock Washer (#29), Ø ¾” Washer (#27), and Rubber Bumper (#14). B.) Attach the Handle Cover (#10) to the tube on the Left Seat Support. Align the holes and insert the Handlebar (#9) halfway through the
Resumen del contenido incluido en la página 12
11
Resumen del contenido incluido en la página 13
Parts list KEY NO. DESCRIPTION Q’ty 1 Main Frame 2 2 Base Stabilizer 2 3 Cross Brace 1 4 Right Seat Support 1 5 Left Seat Support 1 6 Swing Arm 2 7 Swing Base 1 8 Seat Pad 2 9 Handlebar 2 10 Handle Cover 2 11 Handlebar Grip 4 12 Axle 4 13 Bushing 8 14 Rubber Bumper 2 15 Seat Support End Cap 2 16 Nut Cover 2 17 Ball Bearing 8 18 L-shaped Lock Pin 1 19 Cable Strap 1 20 M10 x 3 3/8” Hex Bolt 6 21 M10 x 3” Hex Bolt 2 22 M10 x 1” Allen Bolt 1 23 M10 x 5/8” Allen Bolt 8
Resumen del contenido incluido en la página 14
Operation Tips Observing the following statements and warnings reduces the likelihood of serious or fatal injury. 1. Only two people are allowed to use the teeter totter at the same time with a combined weight of no more than 400 lbs. 2. On-site adult supervision for children of all ages. 3. Instruct children not to walk close to, in front of, behind, or between moving items. 4. Instruct children not to swing empty seats. 5. Instruct children to sit in the center of the seat w
Resumen del contenido incluido en la página 15
® IMPEX INC. LIMITED WARRANTY ® IMPEX INC. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of 2 YEARS from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer Service
