Resumen del contenido incluido en la página 1
REQUIRED TOOLS
AND MATERIALS:
Portable System
• 2 People
Owners Manual
Customer Service Center
� Tape Measure
• N53 W24700 South Corporate Circle � Sussex, WI 53089 � U.S.A.
� Wood Board
(scrap)
� Sawhorse or
Support Table
� Safety Glasses
� Step Ladder - 8ft.
(2.4 m)
� #2 or #3 Phillips
Screwdriver
� (2 each) Wrenches and/or Socket
Wrenches and Sockets (Deep-
Well Sockets are Recommended).
� Extension is Recommended.
1/2" 9/16" 3/4"
AND/OR
1/2" 9/16" 3/4"
� Garden Hose or Sand
Write Model Numbe
Resumen del contenido incluido en la página 2
BEFORE YOU START! WARNING Read and understand warnings listed below before using this product. Failure to follow these warnings may result in serious injury and/or property damage. Owner must ensure that all players know and follow these rules for safe operation of the system. � DO NOT HANG on the rim or any part of the system including backboard, support braces or net. � During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net.
Resumen del contenido incluido en la página 3
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify p
Resumen del contenido incluido en la página 4
IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections, hardware and additional parts are packed inside. NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to the instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. WARRANTY CARD: Please remember to complete your product registration f
Resumen del contenido incluido en la página 5
Get to know the basic parts of your basketball system... FRONT VIEW BACKBOARD RIM ELEVATOR ADJUSTMENT POLE SUPPORT STRUT BASE 5 11/05 ID# M731321
Resumen del contenido incluido en la página 6
PARTS LIST - See Hardware Identifier Item Qty. Part No. Description 1 1 206657 Tank, (Black) 2 1 200628 Wheel Axle 3 2 226401 Wheel, 4“ (Black) 4 1 90021701 Top Pole Section 5 1 904840 Middle Pole Section 6 1 900136 Bottom Pole Section 7 1 202820 Rod, 3/8 O.D. x 4-3/4 Long 8 1 202822 Eyebolt, 3/8-16 x 2-1/2 Long 9 7* 203063 Nylon Insert Lock Nut, 3/8-16 10 2 906206 Tank Strut 11 1 201625 Bolt,Yellow Dichromate, 5/16-18 X 3.60" Long 12 6 203218 Washer, Flat, 3/8 I.D. 13 2 203099 Nylon Insert Loc
Resumen del contenido incluido en la página 7
HARDWARE IDENTIFIER (BOLTS AND SCREWS) Item #18 (5) Item #8 (1) Item #28 (2) Item #15 (6) Item #35 (4) Item #11 (1) Item #23 (1) Item #39 (2) Item #22 (5) HARDWARE IDENTIFIER (NUTS AND WASHERS) Item #13 (2) Item #16 (8) Item #12 (6) Item #38 (1) Item #9 (7*) Item #21 (5) 7 11/05 ID# M731321
Resumen del contenido incluido en la página 8
HARDWARE IDENTIFIER (STEEL SPACERS) Item #45 (1) Item #46 (1) Item #42 (4) HARDWARE IDENTIFIER (PLASTIC SPACERS, CAPS, CLIPS AND OTHER) Item #7 (1) Item #51 (2) Item #36 (1) Item #40 (1) Item #17 (2) Item #32 (1) Item #31 (1) Item #30 (1) 8 ID# M731321 11/05
Resumen del contenido incluido en la página 9
SECTION A: ASSEMBLE THE BASE ITEMS REQUIRED FOR THIS SECTION (2) 1/2” and (2) 9/16" Wrenches This is what your system will look like when you’ve finished this section. AND/OR (2) Socket Wrenches and Sockets 1/2” 9/16” Correctly identify each pole section. Poles have an identification sticker that will be used as a 1. reference point in the next step. Identification Sticker 4 TOP 5 MIDDLE Identification Sticker 6 BOTTOM 9 11/05 ID# M731321
Resumen del contenido incluido en la página 10
While maintaining alignment, bounce pole top (4) and middle section (5) together as shown until 2. they no longer move toward identification sticker. Upright assembly. CAUTION! THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 1-1/2" BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER. IMPORTANT! Align dimple of top pole section (4) into trough of middle pole section (5) as
Resumen del contenido incluido en la página 11
While maintaining alignment, bounce assembly and bottom pole section (6) together as shown 3. until they no longer move toward identification sticker. CAUTION! THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 1-1/2" BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER. IMPORTANT! Align dimple of middle pole section (5) into trough of bottom pole section (6) as shown. 4 5 1-1/2
Resumen del contenido incluido en la página 12
6 Install rod (7) through holes in bottom pole section (6) 4. and eyebolt (8). 7 8 Install wheel axle (2) through wheel carriage (19) and install wheels (3) onto wheel axle (2) with 5. spacers (17) as shown. Insert pole assembly into tank assembly as shown. Secure bottom pole (6) section to tank and wheel carriage as shown. A deep socket is recommended. IMPORTANT! IMPORTANT! WARNING! DO NOT OVER TWO PEOPLE REQUIRED FOR THIS PROCEDURE. TIGHTEN FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SER
Resumen del contenido incluido en la página 13
Secure flat end of tank struts (10) to pole using bolt (11), washers (12), and nut (13), as 6. shown. Rotate the non-secured angled ends of the struts (10) as shown. WARNING! TIGHTEN BOLT (11) IN LOCK NUT (13) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. 12 12 13 6 11 10 6 10 1 10 7. Secure tank struts (10) to the base using bolt (15), washers (12), and nut (16). 10 15 12 1 10 15 12 12 16 12 16 13 11/05 ID# M731321
Resumen del contenido incluido en la página 14
Install pole mount bracket (27) and reinforcement bracket (34) with carriage bolts (28) 8. in lower pole mounting holes as shown. Tighten flange nuts (16) completely. 5 28 16 34 28 27 5 27 34 16 FRONT 6 SIDE 14 ID# M731321 11/05
Resumen del contenido incluido en la página 15
SECTION B: ATTACH THE BACKBOARD ITEMS REQUIRED FOR THIS SECTION This is what your system will look like when you’ve finished this section. (2) 1/2" AND (2) 9/16" AND (2) 3/4" Wrenches AND/OR (2) Socket Wrenches and Sockets 1/2” 9/16” 3/4” 15 11/05 ID# M731321
Resumen del contenido incluido en la página 16
1. Assemble backboard brackets (29) using bolts (35), and nuts (9) as shown. IMPORTANT! 9 Test fit bolts into holes of brackets 9 35 and carefully rock them in a circular motion to ream out paint from holes if necessary. 35 29 NOTE ORIENTATION 35 35 29 29 2. Identify elevator tubes (41 and 44). 44 Upper Elevator tube Toward Pole Toward Board Lower Elevator tube 41 16 ID# M731321 11/05
Resumen del contenido incluido en la página 17
3. Attach lower elevator tubes (41) to backboard brackets (29) using spacers (42) bolt (22) and nut (21) as shown. Insert “T” bolt (36) through Slam Jam bracket (32) as shown. Secure Slam Jam bracket (32) and backboard bracket (29) assemblies to backboard. Use bolt (15) and nut (16) as shown. WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 16 16 21 29 42 42 41 22 41 36 32 IMPORTANT! 15 15 32 Test fit bolts int
Resumen del contenido incluido en la página 18
Attach upper elevator tubes (44) to backboard support brackets (29) using spacers (42), bolt (22), 4. and nut (21) as shown. 21 42 29 44 42 22 44 18 ID# M731321 11/05
Resumen del contenido incluido en la página 19
Support pole on sawhorse. Attach upper and lower elevator tubes (41 and 44) to upper pole 5. section (4) using bolts (22) and nuts (21) as shown. Attach pole cap (14) as shown. 21 21 44 41 4 14 44 41 WARNING! TWO PEOPLE REQUIRED 22 22 FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 19 11/05 ID# M731321
Resumen del contenido incluido en la página 20
Insert locking pin (46) into bracket on adjustment tube (49). Insert cross pin (45) through hole in 6. bracket and locking pin (46) as shown in figure A. Fit left handle (47) onto adjustment tube (49) so the bottom of adjustment tube (49) sits on the two small ribs of the handle as shown in figure B. Fig. A 45 49 45 46 49 47 Fig. B 49 47 20 ID# M731321 11/05
