Manual de instrucciones de Fisher-Price J5970

Resumen del contenido incluido en la página 1

J5970
Instructions
www.fisher-price.com
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required. Tool needed for assembly: Phillips screwdriver (not included).
Water or sand is needed to fill the base (not included).
IMPORTANT! Backboard height should be adjusted only by an adult.
®
Grow to Pro Basketball

Resumen del contenido incluido en la página 2

Parts Hint: Some parts were placed inside the lower post for shipping. Upper Post Net Assembly Backboard 4 Rim 5 Collar 6 Lower Post Ball Return Plug Ball Base Note: Label not shown. CAUTION This product contains small parts 5 #6 x / " Screw - 4 8 in its unassembled state. SHOWN ACTUAL SIZE Adult assembly is required. 2

Resumen del contenido incluido en la página 3

Assembly Ring Tab Rim Groove Ring Groove Ring Tab 3 1  While holding the ring assembly and rim together, turn them over.  Place the loops at the top of the net into the grooves  Insert four screws into the holes in the rim, making sure on the ring. each hole in the rim is still aligned with each screw hole in  Pull each loop through a ring tab, as shown. the net assembly.  Partially tighten the screws with a Phillips screwdriver. Turn the rim over to ensure that the net loops are stil

Resumen del contenido incluido en la página 4

Side Edge Side Edge Assembly Curved End 5 4 4 1 Upper Post 5 2 3 6 5 Large Square Opening Proper label application will help to keep the label looking its best!  Make sure the area where the label will be applied is clean Base and dry. Wipe the backboard with a clean, soft, dry cloth to remove any dust or oils. 7  For best results, avoid applying the label more than once.  Peel the backing from one half of the label. Do not remove  Position the base as shown. all of the backing!  Posit

Resumen del contenido incluido en la página 5

Assembly Wall Backboard ® Fisher-Price Rim Logo Lower Post 4 4 Groove 5 Rib Upper Post 5 Peg 6 Base 6 Groove 9 11  Lean the rim against a wall for support. IMPORTANT! Assembly of the lower post to the base is a permanent assembly.  Locate the pegs on each side of the rim and the grooves on the backboard.  Align the rib on the bottom of the lower post with the ®  Position the backboard with the Fisher-Price logo groove in the opening in the base. facing up. Hint: For easier assembly, app

Resumen del contenido incluido en la página 6

Assembly Care and Maintenance Peg Peg Holes 13  This toy includes an inflatable ball. If the ball becomes soft, inflate it with a standard, manual air pump with a  If the lever comes off, simply re-attach it. standard air needle.  Insert the peg on one side of the lever into the hole in  The ball will contain the correct amount of air when its the collar. circumference measures about 21-22 inches (53-56 cm).  Snap the other peg in the lever into the other hole in Measure the circumfer

Resumen del contenido incluido en la página 7

Adjusting the Rim Height IMPORTANT! Rim height should only be adjusted by an adult. Also, make sure children are not standing below the rim when adjusting the rim height. Backboard 4 Slots 5 Upper Post Lever 6 Upper Post Lower Post Base 1  As assembled, the rim height is 3' (1 m).  To raise the rim height to 4', 5', or 6' (1.2 m, 1.5 m or 3 1.8 m), place your foot on the base and pull up on the backboard with both hands to remove the upper post  To lower the rim height: while holding the

Resumen del contenido incluido en la página 8

Consumer Information Visit us on line at www.service.fisher-price.com ® Call Fisher-Price Consumer Relations, toll-free at 1-800-432-5437, 8 AM - 6 PM EST Monday through Friday. Hearing-impaired consumers using TTY/TDD equipment, please call 1-800-382-7470. Write to us at: ® Fisher-Price Consumer Relations, 636 Girard Avenue, East Aurora, New York 14052. For countries outside the United States: CANADA: Questions? 1-800-432-5437. Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R