Resumen del contenido incluido en la página 1
Design LED 60 TriStrip
Elation Professional™
6122 S. Eastern Ave.
Los Angeles, CA. 90040
www.elationlighting.com
Rev. 3/04/2009 - visage
Resumen del contenido incluido en la página 2
Design LED 60 TriStrip™ ©Elation Professional, Los Angeles Ca. 1 www.ElationLighting.com
Resumen del contenido incluido en la página 3
Design LED 60 TriStrip™ TABLE OF CONTENS 1. General Information……………………………………………………………………… 3 a. Introduction………………………………………………………………………. 3 b. Unpacking………………………………………………………..…………..… 3 c. Customer Support…………………………………………….………………… 3 d. Warranty Registration……………………………………………………..…… 3 2. Safety Instructions………………………………………………………........…………. 5 3. Features……………………………………………………………………………………7 4. General Guidelines………………………………………………………………………. 8 5. Fixture Overview………………………………………………………………
Resumen del contenido incluido en la página 4
Design LED 60 TriStrip™ 1. GENERAL INFORMATION INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable LED fixtures on the market today! The Design LED 60 TriStrip™ has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding saf
Resumen del contenido incluido en la página 5
Design LED 60 TriStrip™ rain or moisture. Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself. Doing so will void your manufactures warranty. Please do not discard the shipping carton in the trash. Please recycle whenever possible. WARRANTY REGISTRATION: The Design LED 60 TriStrip™ comes with a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whe
Resumen del contenido incluido en la página 6
Design LED 60 TriStrip™ 2. SAFETY INSTRUCTIONS To guarantee proper and consistent operation, it is important to follow the guidelines in this manual. Elation Professional will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1. Always be sure that the fan and the air inlets remain clean and are never blocked. Allow about 6” (15cm) between this fixture and other devices or a wall
Resumen del contenido incluido en la página 7
Design LED 60 TriStrip™ sure the power cord is never crimped or damaged. If the power cord is damaged, replace it immediately with a new one of similar power rating. 13. Always disconnect from main power before performing any type of service or any cleaning procedure. 14. Only handle the power cord by the plug. Never pull out the plug by tugging the wire portion of the cord. 15. Please be aware that damages caused by modifications to the device are not subject to warranty. Import
Resumen del contenido incluido en la página 8
Design LED 60 TriStrip™ 3. FEATURES • Tri-Color LED Technology • 62˚ Standard Beam Angle (48˚ Optional with 30˚ Lens Kit) • Removable front cover to allow interchangeable Lenses • Low power consumption • Electronic menu display • Minimal heat emission • Maintenance free operation • Equipped with 60 Three-Watt Tri-Color LEDs • 100,000 hours rated LED life • Linear RGB Color Mixing, 65 million color possibilities • USITT DMX-512 complaint • 5-pin and 3-pin Male and Female XLR Dat
Resumen del contenido incluido en la página 9
Design LED 60 TriStrip™ 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, and other types of architectural installations. Do not attempt operation or installation without a proper knowledge on how to do so. This fixture was designed for indoor use only; use of this fixture outside will void the manufacture’s warranty. Consistent operational breaks will ensure that the fixture will function properly for man
Resumen del contenido incluido en la página 10
Design LED 60 TriStrip™ 5. FIXTURE OVERVIEW 1. Bracket Locking Knob – This knob is used to secure the bracket in place after angle adjustments have been made. 2. Fixture Chassis – Extruded aluminum slotted chassis, allows similar units to be mounted together. See assembly instructions on page 3. Diffusing Lens/LED Assembly – This lens is used to both protect the LEDs as well as diffuse the light output. Tri-Color LED assembly 4. Eye Bolt – This bolt is used a securing p
Resumen del contenido incluido en la página 11
Design LED 60 TriStrip™ 7. Power Output Jack – Use this jack to jump power to another Design LED 60 TriStrip™ 8. 3-Pin DMX Output Jack – This jack is used to send an incoming DMX signal to the next fixture in the DMX chain via a female, 3-pin XLR jack. 9. 3-PIN DMX Input Jack – This jack accepts an incoming DMX signal via a male, 3-pin XLR jack. 10. LED Menu Display - 4-segment menu display. Used to display the DMX address as well as all other menu functions. 11. 5-PIN DMX
Resumen del contenido incluido en la página 12
Design LED 60 TriStrip™ 6. MOUNTING AND INSTALLATION Yoke Assembly – Single Unit Operation (DLED 12 Brick shown for illustration purposes only). The device can be placed directly on the stage floor or rigged in any orientation on a truss without altering its operation characteristics. When connecting the hanging yoke to the fixture, refer to the illustration below. Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas, and away from
Resumen del contenido incluido en la página 13
Design LED 60 TriStrip™ working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury. Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet. Mounting The Design LED 60 TriStrip™ is fully o
Resumen del contenido incluido en la página 14
Design LED 60 TriStrip™ CAUTION! Be sure a qualified electrician performs all electrical connections before attempting any operation. Clamp Mounting The Design LED 60 TriStrip™ provides a unique mounting bracket assembly that allows the unit to stand on flat surface, hang on truss via a clamp, or be used in cluster allow multiple units to rigged together (see the illustration below). Regardless of the mounting option you choose please refer to the safety guidelines in this manu
Resumen del contenido incluido en la página 15
Design LED 60 TriStrip™ 7. UNDERSTANDING DMX DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by lighting and controller manufactures as a form of communication between intelligent fixtures and controllers. DMX allows all makes and models of different manufactures to be linked together and operate from a single controller. This is possible as long as all the fixtures and the controller are DMX compliant. A DMX controller sends the DMX data instructions t
Resumen del contenido incluido en la página 16
Design LED 60 TriStrip™ at 120 ohms, this cable is designed for DMX transmission and may be purchased from your Elation dealer or at most professional lighting retailers. Your cables should be made with a male and female XLR connector on either end of the cable. Also, remember that a DMX line must be daisy chained and cannot be split, unless using an approved DMX splitter Be sure to follow the above figure when making your own cables. Do not use the ground lug on the XLR connec
Resumen del contenido incluido en la página 17
Design LED 60 TriStrip™ DMX-512 connection with DMX terminator A DMX terminator should be used in all DMX lines especially in longer runs. The use of a terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line. Using a line terminator (Elation part:
Resumen del contenido incluido en la página 18
Design LED 60 TriStrip™ to the digital control information sent out from the DMX controller. The allocation of this starting DMX address is achieved by setting the correct DMX address on the digital display located on the head of the fixture. You can set the same starting address for all fixtures or a group of fixtures, or set different address for each individual fixture. Be advised that setting all you fixtures to the same DMX address will subsequently control all fixtures in the s
Resumen del contenido incluido en la página 19
Design LED 60 TriStrip™ 8. DISPLAY MENU MODE Set the starting DMX address ADDR ( ) A001( ) (1-512) ( ) Set the display open or close when no ON/OFF( ) DISP( ) control after 2 minutes FLIP( ) ON/OFF( ) Set the flip display CHAN ( ) 3 CH( ) 3 DMX CHANNELS (RGB) 4 CH( ) 4 DMX CHANNELS (RGB+MASTER DIM) 6 DMX CHANNELS 6 CH( ) 15 DMX CHANNELS 15 CH( ) 60 DMX CHANNELS 60 CH( ) 63 DMX CHANNELS 63 CH( ) UNIT FUNCTIONS AS SLAVE SLAV( ) ON/OFF( ) MANU Fixture will function a
Resumen del contenido incluido en la página 20
Design LED 60 TriStrip™ FADE( ) 0-255 Adjust program 4 fade time STRB( ) 0-255 Adjust strobe rate of program 4 CHS5( ) SPED( ) 0-255 Adjust program 5 speed FADE( ) 0-255 Adjust program 5 fade time STRB( ) 0-255 Adjust strobe rate of program 5 CHS6( ) SPED( ) 0-255 Adjust program 6 speed FADE( ) 0-255 Adjust program 6 fade time STRB( ) 0-255 Adjust strobe rate of program 6 CHS7( ) SPED( ) 0-255 Adjust program 7 speed FADE( ) 0-255 Adjust program 7 fade time STRB( ) 0-
