Resumen del contenido incluido en la página 1
™
Design Wash LED 60
Elation Professional
6122 S Eastern Ave
Los Angeles, Ca 90040
www.elationlighting.com
Rev. 10/06/2009 – visage Version 1.1
Resumen del contenido incluido en la página 2
Design Wash LED 60™ ©Elation Professional, Los Angeles Ca. 2 www.ElationLighting.com
Resumen del contenido incluido en la página 3
Design Wash LED 60™ CONTENTS 1. General Information……………………………………………………………………… 4 a. Introduction………………………………………………………………………. 4 b. Unpacking………………………………………………………..…………..….. 4 c. Customer Support…………………………………………….………………… 4 d. Warranty Registration……………………………………………………..……. 5 2. Safety Instructions………………………………………………………........…………. 6 3. Features…………………………………………………………………………………… 7 4. General Guidelines………………………………………………………………………. 8 5. Fixture Overview…………………………………………………………………………. 9 6. M
Resumen del contenido incluido en la página 4
Design Wash LED 60™ 1. GENERAL INFORMATION INTRODUCTION: Congratulations, you have just purchased one of the most innovative and ™ reliable lighting fixtures on the market today! The Design Wash LED 60, has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding saf
Resumen del contenido incluido en la página 5
Design Wash LED 60™ yourself, doing so will void your manufactures warranty. Please do not discard the shipping carton in the trash. Please save for return shipping in the event service is ever needed or recycle the container whenever possible. ™ WARRANTY REGISTRATION: The Design Wash LED 60 carries a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight
Resumen del contenido incluido en la página 6
Design Wash LED 60™ 2. SAFETY INSTRUCTIONS ™ The Design Wash LED 60 is an extremely sophisticated piece of electronic equipment. To guarantee a smooth operation, it is important to follow the guidelines in this manual. Elation will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1. Always be sure that the fan and the air inlets remain clean and are never blocked. Allow about 6” (
Resumen del contenido incluido en la página 7
Design Wash LED 60™ 3. FEATURES • Pan 540° or 630˚ (User selectable) / Tilt 265° • 9˚ Beam Angle / 22˚ Field Angle • 60 x 3-Watt SSC LED Light Source – (22 x Red, 17 x Green, 15 x Blue, 6 x White) • 100,000 hours rated LED life • Smooth additive RGBW color mixing, 16.7 million colors • Flicker-free operation for television and film • Low power consumption • 3 operation mode: DMX controlled, stand alone or sound activated • Strobe effect: 0~18 flashes per second or random strobe
Resumen del contenido incluido en la página 8
Design Wash LED 60™ 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, etc. Do not attempt operation or installation without a proper knowledge on how to do so. This fixture was designed for indoor use only. Consistent operational breaks may ensure that the fixture will function properly for many years to come. Do not shake the fixture around. Avoid brute force when installing or operating the device.
Resumen del contenido incluido en la página 9
Design Wash LED 60™ 5. FIXTURE OVERVIEW 1. LED Assembly 2. Yoke Assembly 3. Base 4. Carrying Handle 5. LCD Menu Display 6. Menu Button 7. Up Button 8. Down Button 9. Enter Button 10. Control Board Assembly 11. Cooling/Fan Assembly 12. 3-Pin DMX Output 13. Battery On/Off Button 14. 3-Pin DMX Input 15. Fuse Holder 16. Power Cord 17. 5-Pin DMX Output 18. 15-Pin DMX Input ©Elation Professional, Los Angeles Ca. 9 www.ElationLighting.com
Resumen del contenido incluido en la página 10
Design Wash LED 60™ 1. LED Assembly – 60 Philips Rebel LEDs comprise the LED assembly. 22 Red, 17 Green, 15 Blue, and 6 White. 2. Yoke Assembly – This assembly consist of the electronics and motors that control the tilt movement as well as the LED operation. 3. Base Assembly – The base assembly holds and protects all the relative electronics. Avoid bruit force to base as this may seriously effect the operation of this fixture. 4. Carrying Handle – Please use this intergraded ha
Resumen del contenido incluido en la página 11
Design Wash LED 60™ 12. 3-Pin DMX Output Jack – This jack is used to send an incoming DMX signal to the next fixture in the DMX chain via a female, 3-pin XLR jack. 13. Battery On/Off Button – This button is used to turn the display menu on or off when the fixture is not plugged into power. This feature will allow the fixture’s DMX address and wireless setting to be set when the fixture is not connected to a power source. 14. 3-PIN DMX Input Jack – This jack accepts an incoming DMX
Resumen del contenido incluido en la página 12
Design Wash LED 60™ 6. MOUNTING AND INSTALLATION Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas, or in areas were the fixture might be reached by unauthorized personal. Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 times the device’s weight. Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable.
Resumen del contenido incluido en la página 13
Design Wash LED 60™ Mounting points Overhead mounting requires extensive experience, including amongst others calculating working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury. CAUTION! Be sure a qualified electrician performs all electrical connecti
Resumen del contenido incluido en la página 14
Design Wash LED 60™ power cord to the appropriate wall outlet. Clamp Mounting ™ The Design Wash LED 60 provides a unique mounting bracket assembly that integrates the bottom of the base, the included “Omega Bracket,” and the safety cable rigging point in one unit (see the illustration below). When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the “omega bracket”. As an a
Resumen del contenido incluido en la página 15
Design Wash LED 60™ 7. UNDERSTANDING DMX DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers. DMX allows all makes and models of different manufactures to be linked together and operate from a single controller. This is possible as long as all the fixtures and the controller are DMX compliant. A DMX controller sends the DMX data instructions
Resumen del contenido incluido en la página 16
Design Wash LED 60™ must be daisy chained and cannot be split, unless using an approved DMX splitter such as the Elation Opto Branch 4™ or DMX Branch/4™. Be sure to follow the above figure when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior.
Resumen del contenido incluido en la página 17
Design Wash LED 60™ DMX-512 connection with DMX terminator A DMX terminator should be used in all DMX lines especially in longer runs. The use of a terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line. Using a line terminator (Elation part: DMX
Resumen del contenido incluido en la página 18
Design Wash LED 60™ out from the DMX controller. The allocation of this starting DMX address is achieved by setting the correct DMX address on the digital display located on the base of the fixture. You can set the same starting address for all fixtures or a group of fixtures, or set different address for each individual fixture. Be advised that setting all you fixtures to the same DMX address will subsequently control all fixtures in the same fashion, in other words, changing the se
Resumen del contenido incluido en la página 19
Design Wash LED 60™ 8. FIXTURE MENU ™ On-Board System Menu: The Design Wash LED 60 comes with an easy to navigate system menu. This next section will detail the functions of each command in the system menu. To access display Menu via the internal battery, press the UP & DOWN buttons simultaneously. Display will automatically switch off after about 10 seconds from last button press. LCD Control Panel: The control panel located on the base of the fixture allows you to access th
Resumen del contenido incluido en la página 20
Design Wash LED 60™ Default settings shaded. Set Dmx Address A001~AXXX DMX address setting Value Display PAN…… DMX value display Set To Slave Slave1,Slave2,Slave3 Slave setting Auto Program Master / Alone Auto program Music Control Master / Alone Music control Time Information Current Time XXXX(Hours) Power on running time Total Life Hours XXXX(Hours) Fixture running time Last Run Hours XXXX(Hours) Fixture Last times clear Timer Password Password=XXX Timer Password 038 Clear L
