Resumen del contenido incluido en la página 1
WS-9117U
Wireless 433 MHz
Temperature Station
Instruction Manual
1
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS Topic Page Inventory of Contents 3 Quick Setup 4-8 Detailed Setup Guide Battery Installation 9-11 Setting the Time 11-12 Selecting Units of 12-13 Measurement Features Minimum and Maximum 13 Temperatures Resetting Minimum and 13-14 Maximum Temperatures Additional remote 14-16 temperature sensors (optional) Mounting 17-18 Troubleshooting 19-20 Maintenance and Care 21 Specifications 22-23 Warranty Information 24-28 2
Resumen del contenido incluido en la página 3
INVENTORY OF CONTENTS 1. The indoor temperature station (Figure 1) 2. The remote temperature sensor (TX6U) and mounting bracket. (Figure 2) 3. 3 each, 1/2” Philips screws. 4. One strip of double sided adhesive tape. 5. Instruction Manual and Warranty Card. Figure 2 Figure 1 ADDITIONAL EQUIPMENT (not included) 1. 1 Philips screwdriver. 2. 2 Fresh AAA 1.5V batteries. 3. 2 Fresh AA 1.5V batteries. 3
Resumen del contenido incluido en la página 4
QUICK SETUP Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of both units for 10 minutes. 3. Place the batteries into the remote temperature sensor first then into the indoor temperature station. (All remote temperature sensors must be started before the indoor temperature station) 4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES. 4
Resumen del contenido incluido en la página 5
In this time the indoor temperature station and remote temperature sensor will start to talk to each other and the display will show both the indoor temperature and an outdoor temperature. If the indoor temperature station does not display both temperatures after the 10 minutes please retry the set up as stated above. After both indoor and outdoor temperatures are displayed for 15 minutes you can place your remote temperature sensor outdoors and set your time. The remote tempera
Resumen del contenido incluido en la página 6
of resistance. Your distance plus resistance should not exceed 80 ft. in a straight line. NOTE: Fog and mist will not harm your remote temperature sensor but direct rain must be avoided. To complete the set up of your indoor temperature station after the 15 minutes have passed please follow the steps below. 1. Press and hold the “SET/CH” button for 5 seconds. Note: A “12h” or “24h” will appear to the left of the time. (“12h” for AM/PM, “24h” for military time) a. To change b
Resumen del contenido incluido en la página 7
b. When you have your choice shown on the display press and release the “SET/CH” button once. 2. Degree Fahrenheit will now show. a. To change between Fahrenheit and Celsius, press and release the “MIN/MAX” button. b. When you have your choice shown on the display press and release the “SET/CH” button once. 3. An hour will now be flashing. a. Press and release the “MIN/MAX” button until the correct hour is shown. Note: When in the 12h mode there is “PM” displayed under 7
Resumen del contenido incluido en la página 8
the word TIME when in the PM hours. During the AM hours this area will be blank. b. When the correct hour is shown, press and release the “SET/CH” button once. 4. A minute will now be flashing. a. Press and release the “MIN/MAX” button until the correct minutes are displayed. Press and release the “SET/CH” button once more and you are done. 8
Resumen del contenido incluido en la página 9
DETAILED SETUP GUIDE I. BATTERY INSTALLATION A. REMOTE TEMPERATURE SENSOR 1. Remove the mounting bracket. 2. Remove battery cover 3. Observing the correct polarity, install 2 AA batteries—make sure they do not spring free, or start-up problems may occur. Replace cover. 9
Resumen del contenido incluido en la página 10
B. INDOOR TEMPERATURE STATION Note: After the batteries are installed, DO NOT press any buttons. This may interfere with the signals, causing temperatures to register incorrectly. 1. Remove the battery cover on the backside. 2. Observing the correct polarity, install 2 AAA batteries. 3. Replace battery cover. 4. Wait 15 minutes before pressing any buttons. 10
Resumen del contenido incluido en la página 11
5. The indoor temperature station should now show: “-:- -” in the TIME LCD, and temperatures in the INDOOR and OUTDOOR LCD’s. II. TIME A. SETTING THE TIME 1. Press and hold the “SET/CH” button for 5 second, “12h” will appear in the TIME LCD. 2. Press and release the “MIN/MAX” button to select either 12h time (am/pm) or 24h time 3. Press and release the “SET/CH” button 2 times, the hour will flash in the upper left corner. 4. Press and release the “MIN/MAX” button to s
Resumen del contenido incluido en la página 12
5. Press and release the “SET/CH” button to move to the minute setting 6. Press and release the “MIN/MAX” button to set the minutes. 7. Press and release the “SET/CH” button to activate the clock. Note: When in 12h mode, there is only a “PM” display, which appears under “TIME.” If there is no display here it is AM. Make sure you set the time accordingly. III. UNITS OF TEMPERATURE MEASURE A. SELECTING UNITS OF MEASUREMENT 1. Press and hold the “SET/CH” button for 5 second
Resumen del contenido incluido en la página 13
3. Press and release the “MIN/MAX” button to shift between °F and °C. 4. Press and release the “SET/CH” button twice to activate settings. IV. FEATURES A. MINIMUM AND MAXIMUM TEMPERATURES 1. Press and release the “MIN/MAX” button, “MIN” appears in the temperature LCD’s and the recorded minimum temperatures are displayed. 2. Press and release the “MIN/MAX” button to toggle to the maximum temperatures. The time of occurrence of the value for outdoor temperature will also flash.
Resumen del contenido incluido en la página 14
seconds. C. ADDING ADDITIONAL REMOTE TEMPERATURE SENSORS (OPTIONAL) 1. The WS-9117U is able to receive signals from 3 different remote temperature sensors. Following are some brief instructions for the basic set-up of remote temperature sensor units with the WS-9117U. These extra sensors can be purchased through the same dealer as this unit, or by contacting La Crosse Technology directly. A TX6 will monitor temperature only, a TX3U will monitor temperature and display the temp
Resumen del contenido incluido en la página 15
remote temperature sensor units, and in numeric sequence. Second, install batteries into the indoor temperature station. Transmission problems will arise if this is not done correctly and if the total time for set-up exceeds 6 minutes. 2. It is necessary to remove the batteries from all units currently in operation. 3. Remove the battery covers to all remote temperature sensor units. 4. Place all remote temperature sensor units in a numeric sequential order. 5. In sequential order
Resumen del contenido incluido en la página 16
D. VIEWING AND OPERATING WITH MULTIPLE REMOTE TEMPERATURE SENSOR UNITS 1. To view the temperature of a different remote temperature sensor unit, press and release the “SET/CH” button. A shift from one “boxed” number to the next should be observed in the OUTDOOR LCD. 2. To view the Minimum/Maximum temperature: first select from which remote temperature sensor to read data (indicated by the “boxed” number). Pressing and releasing the “MIN/MAX” button will toggle through the minim
Resumen del contenido incluido en la página 17
V. MOUNTING Note: To achieve a true temperature reading, avoid mounting in direct sunlight. We recommend that you mount the remote temperature sensor on an outside North- facing wall. The sending range is 80ft; obstacles such as walls, concrete, and large metal objects will reduce the range. Place both units in their desired location before permanently mounting. A. REMOTE TEMPERATURE SENSOR 1. Remove the mounting bracket from the remote temperature sensor 2. Mount using either
Resumen del contenido incluido en la página 18
that is required is to place the indoor temperature station in an appropriate location. 2. To wall mount, remove the table stand. To do this, pull down on the stand from the rear and rotate forward. a) Fix a screw (not included) into the desired wall, and place the indoor temperature station onto the screw using the hanging hole on the backside. Gently pull the indoor temperature station down to lock the screw into place. 18
Resumen del contenido incluido en la página 19
TROUBLESHOOTING NOTE: For problems not solved, please contact La Crosse Technology via e-mail or phone, or visit our website, www.lacrossetechnology.com Problem: The LCD is faint Solution: Replace batteries Problem: No outdoor temperature is displayed. Solution: 1) Remove all batteries, reinsert into remote temperature sensor first, and then into the indoor temperature station. 2) Place remote temperature sensor closer to the indoor temperature station. 3) Be sure all batter
Resumen del contenido incluido en la página 20
Problem: Temperatures do not match if units are placed next to each other. Solution: Each temperature sensor is manufactured to be accurate to within 1 degree plus or minus and under normal conditions; so two temperature sensors could be as much as 2 degrees different. However, the difference can be exaggerated further because the temperature sensors are designed for different working environments. The indoor sensor is less responsive to ambient air currents because of the shielding
