Resumen del contenido incluido en la página 1
Manuel d’Instructions
Instructions Manual
Manual de instrucciones
KSE912XU
Resumen del contenido incluido en la página 2
INDEX WARNINGS AND REQUIREMENTS .....................................................................................................................................3 RECOMMENDATIONS AND SUGGESTIONS......................................................................................................................6 DIMENSIONS and MAIN PARTS...........................................................................................................................................7 INSTALLATION
Resumen del contenido incluido en la página 3
READ AND SAVE THESE INSTRUCTIONS The Installer must leave these instructions with the homeowner. The homeowner must keep these instructions for future reference and for local electrical inspec- tors’ use. READ THESE INSTRUCTIONS BEFORE YOU START INSTALLING THIS RANGEHOOD WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium setting. Alw
Resumen del contenido incluido en la página 4
W A R N I N G � Venting system MUST lead the air outside the building. � DO NOT expel the air through a ductwork in an attic or other enclosed space. � DO NOT use 4" laundry-type wall caps. � Flexible-type ductwork is NOT recommended. � DO NOT obstruct the flow of combustion and ventilation air. � Failure to follow venting requirements may result in a fire. ELECTRICAL REQUIREMENTS A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit. A timedel
Resumen del contenido incluido en la página 5
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Installation Work And Electrical Wiring Must Be Done By Qualified Person(s) In Accordance With All Applicable Codes And Standards, In- cluding Fire-Rated Construction. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards su
Resumen del contenido incluido en la página 6
RECOMMENDATIONS AND SUGGESTIONS The Instructions for Use apply to several versions of this appliance. Accord- ingly, you may find descriptions of individual features that do not apply to your specific appliance. INSTALLATION � The manufacturer will not be held liable for any damages resulting from incor- rect or improper installation. � Check that the main voltage corresponds to that indicated on the rating plate fixed to the inside of the hood. � The electrical supply must be properly
Resumen del contenido incluido en la página 7
DIMENSIONS and MAIN PARTS Dimensions Components Ref. Q.ty Product Components 1 1 Hood Body, complete with: Controls, Light, Blower, Filters 2 1 Telescopic Chimney comprising: 2.1 1 Upper Section 2.2 1 Lower Section 8a 1 Right Air Outlet Grill Aria 8b 1 Left Air Outlet Grill Aria 10 1 Damper 14.1 2 Air Outlet Connection Extension 15 1 Air Outlet Connection Ref. Q.ty Installation Components 7.2.1 2 Upper Chimney Se
Resumen del contenido incluido en la página 8
INSTALLATION Wall drilling and bracket fixing
Wall marking: � Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the center of the area in which the hood will be installed. � Draw a horizontal line at 24” above the hob. � Place bracket 7.2.1 on the wall as shown about 1/16” from the ceiling or upper limit aligning the center (notch) with the vertical reference line. � Mark the wall at the centers of the holes in the
Resumen del contenido incluido en la página 9
Mounting the hood body � Before attaching the hood body, tighten the two screws Vr lo- cated on the hood body mounting points. � Hook the hood body onto the screws 12a. � Fully tighten support screws 12a. � Adjust screws Vr to level the hood body. Note: The Hood body should be secured to wall studs. If neces- sary, install a wood support behind the dry wall, flush mounted between 2 studs. This will provide the necessary structure and support for mounting. Connections DUCTED VERSION
Resumen del contenido incluido en la página 10
ELECTRICAL CONNECTION � Remove the cover from the Field Wiring Compartment with a phillips screwdriver.
� Feed the Power Supply Cable through the electrical knockout.
Connect the Power Supply Cable to the range- hood cable. At- tach the Power Supply Cable grounding lead to the green screw provided. Attach the White lead of the power supply to the White lead of the rangehood with a twist-on type wire connec- tor. Attach the Black lead of th
Resumen del contenido incluido en la página 11
USE Control board Key Function Display A Switches the motor on and off at the latest Indicates the selected speed selected speed B Decreases the suction speed. - C Increases the suction speed. - D By pressing this key it is possible to start the HI and the remaining time appear alternately. intensive speed from any previously selected The spot down at the right side flashes once a speed. This speed has been timed at 10 min- second. utes. After that time the system activates auto- mat
Resumen del contenido incluido en la página 12
CARE Metal grease filters Filters can be washed in the dishwasher. They need to be washed when FF-sign appears on the display or in any case every 2 months, or even more frequently in case of particularly intensive use of the hood. Alarm reset � Press the G-key for at least 2 seconds. Cleaning � Remove the filters one at a time, supporting them with one hand and turning the safety knobs (pull and turn). � Wash the filters. Pay attention not to bend them. Make sure that filters are co
Resumen del contenido incluido en la página 13
Charcoal filter (ductless version) This filter cannot be washed or regenerated. It has to be replaced when the EF appears on the display or at least once every 4 months. Activation of the alarm signal � In the recycling version hoods the filter saturation alarm has to be activated during the in- stallation or later. � Switch off the hood and the lights. � Press the E-key for about 5 seconds until the LED on the display start to move. � Press the B-key within 5 seconds until a confirmatio
