Resumen del contenido incluido en la página 1
Color TFT LCD Monitor
MM56A
Owner’s Manual
128-6544
1 of 12
Released: 02-11-04
Resumen del contenido incluido en la página 2
EXPLANATION OF GRAPHIC SYMBOLS CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSON- NEL The lightning flash with the arrowhead within a triangle is intended to alert tell the user that parts inside the product are The exclamation point within a triangle is intended to alert the user that important operating and servicing instructions WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT OP
Resumen del contenido incluido en la página 3
IMPORTANT An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or naviga- tion. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function then the vehicle is in ‘park’ or when the vehicle’s parking brake is applied. An LCD pan
Resumen del contenido incluido en la página 4
B. Installation: Front View Top View Clamshell Monitor Key 1.Installation will vary from vehicle to vehicle, as headrests in vehicles are not standard. 2. This unit is intended for installation by professional installers. 3. The kit consists of the screen assembly, a clam shell housing, a trim ring, 1 key to remove the screen from the housing, and a wiring harness. 4 128-6544 4 of 12
Resumen del contenido incluido en la página 5
Headrest Mounting: Mounting 1) Remove the headrest Tray Trim Headrest from the vehicle for easi- Monitor Ring est installation. 2) Lay headrest on a flat sur- face. 3) Center trim collar on head- rest as shown. NOTE: Depending on the angle of the headrest, the Trim Ring and housing may be mounted upside down. 4) Using a Permanent Marker, mark headrest material along the interior of the Trim Ring. 5) Remove the Trim Ring and mark an “X” from cor- ner to corner as shown. 5 128-6544 5 of 12
Resumen del contenido incluido en la página 6
6) Using the utility knife, cut the headrest material along the “X” lines. Do not cut the mate- rial along the other lines at this time. 7) This will leave you with an “X” cut as shown. 8) Pull the flaps up and cut the foam beneath the material to the proper depth. Cut all four sides of the foam. 9) Using your fingers, tear the foam out of the headrest leav- ing a recess where the shell will be inserted. NOTE: At this point you will need to install the harness up through the area into the rece
Resumen del contenido incluido en la página 7
10) Lay the flaps of the headrest ma- terial down into the recess and in- sert the Mounting Tray into the re- cess. Check for fit. If it does not fit properly, you may need to re- move some more foam. NOTE: The Mounting Tray will need to be secured to the headrest, either by using tie straps, screws, etc... 11) Guide the cable through the side opening of the Mounting Tray and plug it into the Monitor. Make sure the connector locks into place. In- sert the Monitor into the Mount- ing Tray and
Resumen del contenido incluido en la página 8
C. Controls/Indicators/Connectors: Front View 1 2 3 4 5 6 1. AUX. Input Jack 2. Earphone Jack 3. Color Adjust Up/Down Buttons 4. Brightness Adjust Up/Down Buttons 5. Power On/Off Button 6. Volume Increase/Decrease Thumbwheel Control 8 128-6544 8 of 12
Resumen del contenido incluido en la página 9
Exploded View HEADREST TRIM HEADREST SHROUD 6 COLOR MONITOR 10 7 8 11 9 12 6. DIN Connectors 7. Signal Cable 8. Black Wire (Ground) 9. Red Wire (+12 Vdc Input) 10. White RCA Jack (Audio Input L) 11. Red RCA Jack (Audio Input R) 12. Yellow RCA Jack (Video Input) 9 128-6544 9 of 12
Resumen del contenido incluido en la página 10
D. Operation: 1. Connect the red monitor power input wire (9) to a DC power source (Red = +12 VDC), and the Black wire (8) to ground. 2. Connect the external video source output signal (from VCP, DVD, TV etc.) to the VIDEO IN jack (12). 3. Press power button (4) to turn the monitor on and off. The backlight for the button will intensify. 4. Adjust the volume increase/decrease thumbwheel (5) to adjust the volume level. 5. Press the Color (2) and Brightness (3) buttons to adjust the respec- tiv
Resumen del contenido incluido en la página 11
THIS PAGE LEFT BLANK INTENTIONALLY 11 128-6544 11 of 12
Resumen del contenido incluido en la página 12
E. Specifications: Display 5.6” Color TFT LCD Resolution 960 (W) x 234 (H) Lines Active Area 114.2 (W) x 83.5 (H) mm Backlight CCFL Input Signal NTSC/PAL(auto-switch) Composite video signal 1Vp-p/75ohm Lamp Life 10,000 Hours Audio Specifications: Input Impedance 10 K-Ohms Audio Output 0.3 W Maximum Earphone 16 Ohms/32 Ohms Bandwidth 15 kHz Input Level 1 Vp-p Power Source +12 VDC +/-15% (Ripple=0.5 Vp-p Max) Power Consumption 8 Watts Max Brightness 300 Nit Typical Viewing Angle Top 30 Degrees
