Resumen del contenido incluido en la página 1
LA112
(6901-100189 <01>)
Backed by CLO
Thank you for choosing the Sanus Systems LA112 motorized mount. The LA112 is a remote-controlled automated
mount for flat panel monitors designed to be fully adjustable. The LA112 supports flat panel monitors with a
maximum weight of 81 kg (180 lbs.), ranging in size from 40 in. – 63 in. (102 cm – 106 cm). The LA112 extends up to
12 in (30 cm) from the wall.
CauTION
Do not use this product for any purpose not explicitly specified by Sanus Systems. Impr
Resumen del contenido incluido en la página 2
3/8 1/8 in. 1/2 in. Supplied Parts and Hardware Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the item to your dealer; contact Sanus Systems Customer Service. Never use damaged parts! WaRNING This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children! Adapters are not included with the LA112. If you need an adapter, contact Sanus Systems Customer Service
Resumen del contenido incluido en la página 3
T P P E R R S E E NOTE: Items [1] through [4] are pre-assembled. POWER X-ARM VCR TV DVD CBL SET P1 P3 SEL IN/OUT P2 P4 MENU EXIT [01] x 1 [02] x 1 [04] x 4 [03] x2 MUTE + + VOL CH FAV X-ARM VCR TV DVD CBL SET P1 P3 SEL IN/OUT INFO TV/VCR GUIDE P2 P4 MENU EXIT MUTE + + [07] x 1 [06] x 1 [08] x 1 1 2 3 VOL CH [05] x 2 FAV 1 2 3 4 5 6 4 5 6 7 8 9 0 7 8 9 ENTER LAST 5/16 in. 5/16 x 2.5 in. M5 x 16 mm M5 x 30mm 0 Remote Control [12] x 4 [11] x 6 [13] x 4 [09] x 1 [10] x 6 M4 x 12mm M5 x 12mm M6 x 12m
Resumen del contenido incluido en la página 4
CauTION Avoid potential injuries or damage to equipment. The LA112 is designed to mount to vertical walls only. Do not attempt to mount the LA112 to ceilings or non-vertical walls. For indoor use only! Do not mount outdoors. CauTION Avoid potential injuries or damage to equipment! Always observe the LA112 while in motion. To stop the motion, press any of the arrow keys on the remote control. Never allow children to operate the LA112. CauTION Avoid potential injuries or damage to equipment!
Resumen del contenido incluido en la página 5
1: Remove Wall Plate from a rm [01] [a] [B] The LA112 is shipped with the wall plate and arm assembled. You must remove the wall plate before installation. Loosen the two fasteners [a] securing the wall plate [01] to the arm assembly [02]. Tilt the wall plate away from the arm assembly then lift the wall plate to disengage it from the hooks [B]. [02] 6901-100189 <01>
Resumen del contenido incluido en la página 6
P P R R E E 2: Remove Mounting Brackets [27] You must remove the two TV Mounting Brackets from the LA112 before attaching the arm to the wall plate. Remove the hex screws [a] from the mounting brackets [03]. Pull the safety clips [04] from the back of the mounting brackets, then remove the mounting brackets from the arm assembly. [27] [a] X-ARM VCR TV DVD CBL SET P1 P3 SEL IN/OUT P2 P4 MENU EXIT X-ARM VCR TV DVD CBL SET [04] P1 P3 SEL IN/OUT P2 P4 [03] MENU EXIT 6901-100189 <01> S S E E T T
Resumen del contenido incluido en la página 7
3: Mount Wall Plate For Wood Stud Walls 1/8 in. Max. 43 cm (17 in.) [01] 2x Min. 6.5 cm (2.5 in.) 6x 6x [10] 6x 6901-100189 <01>
Resumen del contenido incluido en la página 8
For Concrete Block or Brick Walls 1/2 in. [01] Min. 6.5 cm (2.5 in.) 6x 6x [11] 6x CauTION Avoid potential injuries and / or property damage! Never drill into the mortar between concrete blocks! [10] 6x 6901-100189 <01>
Resumen del contenido incluido en la página 9
4: Install a rm a ssembly to Wall Plate [02] [01] Hang the arm assembly [02] over the top rail of the wall plate [01]. Be sure both hooks on the arm assembly engage with the rail. Align the arm assembly to the desired location on the wall plates. Secure the bottom of the arm assembly to the wall plate by tightening the two fasteners [a] at the bottom of the arm assembly. [a] 6901-100189 <01>
Resumen del contenido incluido en la página 10
5: Set the Monitor Width CauTION Avoid potential injuries and / or property damage! Do not use the monitor manufacturer’s “screen size”; you must measure the width of the monitor case, including any speakers attached to the sides. CauTION The LA112 restricts movement based up on the TV widteh set on the side controls. The TV widthe must be set correctly before operating the LA112. To set the monitor width, determine the correct code from the chart below. Measure monitor width, including a
Resumen del contenido incluido en la página 11
P R E 6: Install Mounting Brackets CauTION If your television came with mounting bolts use those. If not, select bolts from those supplied with your LA112. Bolts selected must match the manufacturer’s recommendations. Top Circular holes and hook [03] [18, 19, 20] [12, 13, 14, 15, 16, 17] [21, 22, 23] 6.1 Connect the IR receiver cable [06] to the receiver port on the arm assembly. On the remote control [09], press the “X-aRM ” button to activate the remote. Then press the “SEL-IN/OuT” bu
Resumen del contenido incluido en la página 12
7: Route Cables For Power Outlets Located Outside the Bellows [B] Cable Loops Cable Tie Anchor [C] IR Reciever Cable Bar Plug Cable Hole Bellows No Cable No Cable 2” (5 cm) 2” (5cm) Bottom Cross Bar [a] [26] Power AV Cables to TV [06] [07] to TV IR Reciever Eye TV Power Outlet AV Cables from (outside bellows) Component CauTION Avoid potential property damage! Keep all cables away from the center beam of the arm assembly. Do not place cables closer than 5cm (2 in.) on either side of the beam.
Resumen del contenido incluido en la página 13
For Power Outlets Located Inside the Bellows CauTION Avoid potential property damage! Keep all cables away from the center beam of the arm assembly. Do not place cables closer than 5cm (2 in.) on either side of the beam. [B] TV Power outlet TV Power & [a] inside belows. IR Receiver Hook AV Cable Loop Cable Tie Anchor [C] Cable Bar [06] Cable Hole Bellows No Cable No Cable 2” (5 cm) 2” (5 cm) Bottom Cross Bar AV Cables TV Power to TV Cord IR Receiver Eye AV Cables from [08] Component Route t
Resumen del contenido incluido en la página 14
8: Install Monitor to Wall Plate HEAVY! You will need assistance [27] with this step. [a] Position the hooks at the top of the mounting brackets over the top cross bar [a]. Guide the bottom of the mounting brackets down and towards the arm assembly until the brackets engage with the bottom cross bar. Install the four safety clips [04] as shown. Secure the safety clips with the fasteners [B]. [B] [B] [04] 6901-100189 <01>
Resumen del contenido incluido en la página 15
9: Calibrate the a rm Calibrate a rm to the Monitor NOTE: LA112 must be calibrated to the TV to avoid hitting the wall. 1. Turn the control box power switch to “Off” . 2. While holding down the “Set” button, turn the control box power switch back on and continue to hold Set until “Ct” appears in the LED display. 3. Stand away from the LA112 as it calibrates. LA112 will move back to the home position against the wall when calibration is complete. 4. If your TV is not parallel with the wall, pro
Resumen del contenido incluido en la página 16
T T T T t T T T T T T T T T T T T T T P P P p P P P P P P P P P P P P P P P P P P P P P P P P P P P P P P P P P E E E e E E E E E E E E E E E E E E E R R R r R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R S S S s S S S S S S S S S S S S S S S E E E e E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E POWER X-ARM VCR TV DVD CBL POWER X-ARM VCR SET TV DVD CBL SET P1 P3 SEL IN/OUT P1 P3 P2 P4 POWER X-ARM SEL IN/OUT VCR MENU EXIT P2 P4 TV DVD CBL MUTE + + MENU SET E
Resumen del contenido incluido en la página 17
T T T T P P P P P P P P E E E E R R R R R R R R S S S S E E E E E E E E Programming the Preset Position Keys CauTION To avoid injury or property damage, confirm correct TV width is set before programming the Perset Positions. Do not come in contact with the LA112 while it is in motion. 1. Turn control box power switch to “On” . POWER X-ARM POWER X-ARM 2. Press + VCR VCR TV DVD TV DVD C POBWLER X-ARM CBL 3. Move the LA112 to the desired position for preset using the remote
Resumen del contenido incluido en la página 18
T T T T P P P P P P P P E E E E R R R R R R R R S S S S E E E E E E E E POWER X-ARM VCR Programming the Remote to Operate an Existing TV TV DVD CBL SET POWER X-ARM 1. Turn your TV on. VCR TV DVD CBL 2. Find your TV’s codes from the list on the following page. POWER X-ARM POWER X-ARM P1 P3 VCR VCR SEL SET TV DVD 3. Press and hold un + CBLtil the TV button stays lit. IN/OUT TV DVD CBL P2 P4 4. Point the remote at your TV and enter a code from the list
Resumen del contenido incluido en la página 19
Programming Codes TV Programming Codes TV Brand Code Numbers TV Brand Code Numbers Admiral 220 160 081 072 Emerson 245 155 154 143 096 076 051 048 047 043 028 005 004 001 Advent 231 Fisher 057 007 Aiwa 213 Fujitsu 244 Akai 146 001 Funai 245 043 028 Amark 143 Funai 245 043 028 Ampro 073 Futuretech 043 Amstrad 052 Gateway 041 202 Anam 242 131 080 056 043 GE 220 165 160 155 144 074 073 056 034 009 008 004 001 Aoc 058 004 001 Gradiente 218 Apex 247 haier 203 Audiovox 076 Hallmark 004 Blaupunkt 088
Resumen del contenido incluido en la página 20
Programming Codes TV Programming Codes, continued TV Brand Code Numbers TV Brand Code Numbers Nad 025 015 Soundesign 043 028 004 003 NEC 056 040 024 019 016 001 SSS 043 004 Nikei 043 Supremacy 002 Olevia 045 Sylvania 249 245 240 229 226 211 164 160 127 064 063 060 059 003 Onking 043 Symphonic 245 Omwa 043 Tandy 081 Optonica 081 019 Signature 072 Orion 096 Tatung 062 056 Panasonic 250 249 238 227 164 080 056 034 Technics 080 034 Philco 164 064 063 060 059 056 024 004 Techwood 004 003 0011 Philli
