Resumen del contenido incluido en la página 1
ENGLISH
OWNER’S MANUAL
LCD MONITOR
Please read this manual carefully before operating your set and
retain it for future reference.
LCD MONITOR MODEL
E2211PU
E2411PU
www.lg.com
Resumen del contenido incluido en la página 2
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national stan
Resumen del contenido incluido en la página 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures wh
Resumen del contenido incluido en la página 4
Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product. An electric shock may occur. (Do not use chemicals such as benz
Resumen del contenido incluido en la página 5
Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Power Cord User's Guide/Cards 15-pin D-Sub Signal Cable DVI-D Signal Cable (To set it up, this signal cable may be (This feature is not available in all attached to this product before countries.) shipping out.) Audio Cable USB Cable NOTE This accessories may look different from those shown here. User must use shielded signal i
Resumen del contenido incluido en la página 6
Connecting the Display E2211PU Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices are turned off. Connecting the stand base 1. Place the monitor with its front facing downward on a cushion or soft cloth. 2. Assemble the Stand Base into the Stand Body. Be sure don't pull out the Stop Pin and make the Stand Base direction as shown. Stop Pin Stand Body Stand Base WARNING The tape and locking pin may only be removed from those mon
Resumen del contenido incluido en la página 7
Connecting the Display E2211PU 3. Use a coin on the back of the stand base and turn the screw clockwise to tighten. 4. Lift and turn the monitor to face towards the front after the connection is made to the female part of the cable you're attaching. Removing the stand base 1. Place the monitor with its front facing downward on a cushion or soft cloth. 2. When you desire to disintegrate the monitor from the stand base, use a coin to turn the screw counterclockwise. IMPORTANT This illustrat
Resumen del contenido incluido en la página 8
Connecting the Display E2411PU Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices are turned off. Connecting the stand base 1. Place the monitor with its front facing downward on a cushion or soft cloth. 2. Assemble the Stand Base into the Stand Body. Be sure don't pull out the Stop Pin and make the Stand Base direction as shown. Stand Body Stand Base Stop Pin 3. Once assembled take the monitor up carefully and face the front s
Resumen del contenido incluido en la página 9
Connecting the Display E2411PU Removing the stand base 1. Place the monitor with its front facing downward on a cushion or soft cloth. 2. While pressing the latches, push the stand base in the direction of the arrow to separate from the stand body. IMPORTANT This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foo
Resumen del contenido incluido en la página 10
Connecting the Display Positioning your display After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range Swivel Range : 356˚ Height Range : maximum 4.33 inches (110.0 mm) 110.0 mm * Please be sure to remove the Locking pin to adjust the height. 9
Resumen del contenido incluido en la página 11
Connecting the Display When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). When adjusting the height of the screen, do not put your finger(s) in between the head of the monitor and the stand base. You can hurt your finger(s). WARNING You do not need to replace the Locking pin after it is removed, to adjust its height. ERGONOMIC It is recommended that in order to maintain an ergonomic and comfortab
Resumen del contenido incluido en la página 12
Connecting the Display Using the Pivot function -The pivot function allows you to rotate the screen 90 degrees clockwise. 1. Lift the monitor to its highest height to utilize the Pivot function. o 2. Landscape & Portrait : You can rotate the panel 90 clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the screen to access the Pivot function. If the monitor head touches the Stand Base, then the Stand Base could crack. Head section Stand se
Resumen del contenido incluido en la página 13
Connecting the Display Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect signal input cable and power cord in order, then tighten the screw 1 2 of the signal cable. A Connect DVI-D(Digital signal) Cable B Connect D-sub(Analog signal) Cable C Connect Audio Cable NOTE This is a simplified representation of the rear view. This rear view represents a general mo
Resumen del contenido incluido en la página 14
Connecting the Display 3. Put the power cord and cables into the cable holder.(Only E2411PU) Cable Holder 4. Press the power button on the front panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. (Only Analog Mode) Power Button NOTE ‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the displa
Resumen del contenido incluido en la página 15
Connecting the Display Connecting the USB(Universal Serial Bus) Cable 1. You can use the USB port at the back of the monitor to connect peripherals (USB mouse, USB keyboard, etc.) to the monitor, not to the computer. Two USB Downstream ports Connect these ports to a mouse, USB keyboard,memory stick with current spec under 100mA. One USB Upstream port Connect this port to the downstream port of a computer, laptop or USB monitor (Your computer or USB monitor must support USB and have U
Resumen del contenido incluido en la página 16
Control Panel Functions Front Panel Controls MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. SUPER ENERGY Use this button to enter SUPER ENERGY SAVING menu.For more information, ref
Resumen del contenido incluido en la página 17
Control Panel Functions AUTO Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO button before entering the On Screen Display(OSD). (Only Analog Mode) This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is E2211PU/E2411PU : 1920 x 1080 When two input signals are connected, you can select the INPUT Button input signal (D-SUB/DVI) you want. When only one signal (SOU
Resumen del contenido incluido en la página 18
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. To make adjustments in the On Screen Display, follow these steps: Press the discretionary Button, then
Resumen del contenido incluido en la página 19
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. DSUB : D-SUB(Analog signal) input DVI-D : DVI-D(Digital signal) input Main menu Sub-menu Supported input Description MENU VOLUME To adjust the volume DSUB DVI-D To adjust the brightness of the BRIGHTNESS screen To adjust the image size ORIGINAL RATIO COLOR TEMP To customize the color of the screen (PRESET / USER) To adjust the contrast of th
Resumen del contenido incluido en la página 20
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Menu Name Icons Sub- menus Button Tip Exit Adjust (Decrease/Increase) Select another sub-menu Restart to select sub-menu NOTE OSD (On Screen Display) menu languages on the monitor may differ from t
