Resumen del contenido incluido en la página 1
OHM641
6.4Ó LCD
Color Monitor
OWNER’S MANUAL
Resumen del contenido incluido en la página 2
INTRODUCTION The Clarion OHM641 is a full-featured 6.4" LCD Color Monitor. It can be integrated into a mobile multimedia system. The OHM641 has the following features: • 6.4” wide-screen color LCD panel • A bright, clear screen • Video input terminal ABOUT THE MANUAL AND W ARRANTY To start enjoying your new Clarion monitor, please read the instructions listed in this manual. Keep all instructions for future reference. Please fill out and send in the enclosed warranty card to protect your purc
Resumen del contenido incluido en la página 3
7. Do not let the set become hot. If temperature in the car is high or the set has been exposed to direct sunlight and is hot, lower the temperature before using it. (The liquid crystal panel will work properly within a temperature range of 30 – 113 degrees F.) 8. In extremely cold temperatures, the movement of the picture may be slow and the picture may be dark, but this is not a malfunction. The set will work normally once the temperature increases. 9. Small black and shiny dots inside the li
Resumen del contenido incluido en la página 4
WIRING PRECAUTIONS Read all wiring precautions. If you are not sure of the connections, contact your authorized Clarion dealer. 1. Disconnect the negative (-) lead of the battery before making any power connections. 2. When creating passage holes for the power wires, use grommets to eliminate any sharp edges created during drilling. This will protect the wire from being nicked and causing a short circuit. 3. When connecting the ground lead, fasten the ground lead (black) securely to a clean met
Resumen del contenido incluido en la página 5
4. Place the gasket around the housing and plug the cables into the monitor. Mount the housing to the mounting bracket with the 4 machine screws provided. 5. You can now run the IR, power and video cables to their respective destinations. If you’re using the VDH9600 or DVD9600, you can make all of your connections there. PICTURE ADJUSTMENT Brightness To adjust the picture brightness, use the Brightness UP and DOWN buttons located on the front panel of the OHM641. Press the UP button to increas
Resumen del contenido incluido en la página 6
APPLICATIONS With the VDH9600, TTX001 and the FM100S 1. Pick a location to mount the tuner. Typically the tuner will be located close to the VCP or DVD player.Avoid areas with excessive heat or moisture and mount the tuner. 2. Mount the TV antenna (ZCB-303 or equivalent) and plug into the tuner. 3. Plug the 16 pin to A/V out connector into the tuner. Plug the A/V RCA cables, IR extension and power plug into the 16 pin connector and run to the video player. 4. Plug the A/V RCA cable into the A/V
Resumen del contenido incluido en la página 7
• Turn the modulator and the radio on and tune to the modulated frequency. Turn the FM100S’s switch on. The audio can now be heard over the sound system. You can control the video player and the TV tuner by pointing their respective remotes at the IR eye in the monitor. 7
Resumen del contenido incluido en la página 8
Stand alone with the TTX001 and the WH100 1. Pick a location to mount the tuner. Avoid areas with excessive heat or moisture and mount the tuner. Plug the 16 pin to A/V output connector into the tuner. 2. Mount the TV antenna (ZCB-303 or equivalent) and plug into the tuner. 3. At the OHM641, plug in the video RCA, IR extension and power cables supplied with the OHM641 and run to the tuner. Plug the video RCA and IR extension into the tuner. 4. At the WH100 transmitter, plug in the audio RCAs and
Resumen del contenido incluido en la página 9
OPTIONAL REMOTE CONTROL BA TTERY INSTALLATION • Insert 2 AAA batteries into the compartment located on the back of the unit, observing the proper polarity. NOTES: • Each time you change the batteries, you must reprogram the channels. • We suggest you use alkaline batteries; do not use rechargeable batteries. • Always change all the batteries at the same time. OPTIONAL REMOTE CONTROL OPERA TION • To use the remote control, press the Power button to turn on the remote. • Press the TV/VIDEO button
Resumen del contenido incluido en la página 10
CARE AND MAINTENANCE Cleaning the cabinet: • Use a soft, dry cloth to gently wipe off any dirt. • Do not use benzene, thinner, car cleaner, etc., as these substances may damage the cabinet or cause the paint to peel. Cleaning the LCD panel: • Use a soft, dry cloth to gently wipe off any dust. • The surface is easily scratched; do not rub it with hard objects. TROUBLESHOOTING Before assuming malfunction of the unit, check the following: Problem: Power indicator LED is off. Solution: • The fu
Resumen del contenido incluido en la página 11
Problem: The power was turned off when driving on bumpy roads. Solution: • Severe vibration to the operation panel activated the DCP’s sensor. Press the POWER button again to turn the power ON. PRODUCT SPECS Display Type: Color TFTActive Matrix LCD Screen Size: 6.4” (Actual Panel Size) Pixels: 320 x 234 Screen Resolution: 224,640 Dots Power Source Voltage: DC 11 - 15 V Power Consumption: 0.8A Max. (0.8A or Less) Operation Temperature: 30 - 113 degrees F NOTES 11
Resumen del contenido incluido en la página 12
661 W. Redondo Beach Blvd. Gardena, CA 90247 1-800-GO-CLARION www.clarion-usa.com OHM641-10 Rev.3 (03/00)
