Manual de instrucciones de Metra Electronics 99-8219

Resumen del contenido incluido en la página 1

INSTALLATION INSTRUCTIONS FOR PART 99-8219
APPLICATIONS
Toyota FJ Cruiser
2007-2009
99-8219
KIT FEATURES
• DIN radio provision with pocket
• ISO radio provision with pocket
KIT COMPONENTS
• A) Radio Housing • B) Housing Brackets • C) ISO Snap In Brackets • D) Trim Plate
WIRING AND ANTENNA CONNECTIONS
B
(Sold Separately)
Wire harness:
A
• 70-1761 Toyota 1987-up
Antenna adapter:
• Not required
D
C
TOOLS REQUIRED:
Phillips Screwdriver Or Panel Removal Tool
1-800-221-0932

Resumen del contenido incluido en la página 2

99-8219 TABLE OF CONTENTS Dash Disassembly - Toyota FJ Cruiser 2007-2009 . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly * - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . 2 - ISO Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..4 *Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installa

Resumen del contenido incluido en la página 3

DASH DISASSEMBLY 99-8219 TOYOTA FJ CRUISER 2007-2009 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove two Phillips screws from bottom part of side trim panels. Figure A) 3 Using a panel removal tool, carefully remove the side trim panels. (Figure B) Remove (2) Phillips screws from radio 4 trim panel. (Figure C) B 5 Using panel removal tool, carefully remove radio trim panel. (Figure D) 6 Remove (4) 10mm bolts securing the radio. 7 Unplug and remove r

Resumen del contenido incluido en la página 4

KIT ASSEMBLY 99-8219 DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the housing brackets onto the side of the radio housing until the clips engage. Note: Brackets are marked left and right. (Figure A) Slide the DIN cage into the Radio 2 Housing and secure by bending the metal locking tabs outward. (Figure B) 3 Slide the aftermarket radio into the cage and secure. (Figure C) B Continue to final assembly. C 2

Resumen del contenido incluido en la página 5

KIT ASSEMBLY 99-8219 ISO RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Slide the housing brackets onto A the side of the radio housing until the clips engage. Note: Brackets are marked left and right. (Figure A) 2 Mount the ISO Brackets to the aftermarket radio using the screws supplied with the radio. (Figure B) Slide the radio into the radio 3 housing until the side clips engage. Snap the Trim-plate into B the Radio Housing. (Figure C)

Resumen del contenido incluido en la página 6

KIT ASSEMBLY 99-8219 FINAL ASSEMBLY A A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassembly.

Resumen del contenido incluido en la página 7

99-8219 NOTES 5

Resumen del contenido incluido en la página 8

99-8219 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 05/13/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION INST99-8219