Resumen del contenido incluido en la página 1
H-CDM8019
CD/MP3-RECEIVER + 13 cm 2 way coaxial acoustic system
CD/MP3- + 13 2-
Instruction manual
Resumen del contenido incluido en la página 2
Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future. Table of contents Table of contents ....................................................................................................................................................3 Instruction manual for CD/MP3-Receiver...............................................
Resumen del contenido incluido en la página 3
Instruction manual for CD/MP3-Receiver Important safeguards Using the device at temperature below -10º may cause the breakage of the device. Before using please heat up the passenger compartment to the recommended temperature! Read carefully through this manual to familiarize yourself with this high-quality system. Disconnect the vehicle's negative battery terminal while mounting and connecting the unit. When replacing the fuse, be sure to use one with an identical amperage rating. Using a f
Resumen del contenido incluido en la página 4
Accessories 1. Nut 5 mm 1 pc. 2. Spring washer 2 pcs. 3. Screw M5x25 mm 1 pc. 4. Screw 1 pc. 5. Plain washer 2 pcs. 6. Strap 1 pc. 7. Operating instructions 1 pc. 8. Key 2 pcs. 9. Mounting collar 1 pc. 10. Wire connector 1 pc. 11. Removable face plate case 1 pc. 12. Trim plate 1 pc. 13. Warranty card 1 pc. 14. Customer information 1 pc. 15. ISO connector 1 pc. 5
Resumen del contenido incluido en la página 5
Installation/Connections First complete the electrical connections, and then check them for correctness. If you are not confident working with electrical wiring, removing and reinstalling interior panels, carpeting, dashboards or other components of your vehicle, please call your dealer in order to have the unit professionally installed. Before installation 1. Remove the old unit from the dashboard. Remove the outer trim frame. Insert the keys supplied with the old unit into both sides of the
Resumen del contenido incluido en la página 6
Installation method A WARNING: Disconnect negative battery terminal from battery before starting installation. Consult the vehicle’s owner’s manual for proper instructions. 1. After removing the old unit and mounting sleeve, insert supplied mounting sleeve in the opening. 2. Bend the tabs on the mounting sleeve to keep the mounting sleeve firmly in place. 3. Attach wires from the unit to existing wires. See wiring connections diagram. Insert the unit into dashboard. Then apply the trim frame to
Resumen del contenido incluido en la página 7
Installation method B Note: Outer trim frame, hook, and mounting sleeve are not used for this installation. This is only intended as a general guide; contact the vehicle's manufacturer for specific instructions. This method of installation uses the screw holes at the sides of the unit and the holes of the existing vehicle mounting bracket. 1. Remove the hooks on both sides. 2. Align the screw holes of the mounting bracket supplied with the car and the screw holes of the main unit. Tighten the 2
Resumen del contenido incluido en la página 8
Detaching the front panel Press RELEASE button to remove the panel. Attaching the control panel Insert the left side of the control panel into the main unit. Press the control panel on to the right side of middle of it until a “click” sound is heard. Caution: Do not insert the control panel from the right side. It can damage the control panel. The control panel can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop it or subject it to strong
Resumen del contenido incluido en la página 9
Electrical connections Speaker Wiring Notes Follow the above wiring diagram to install the head unit with new or existing speakers. This unit is designed for use with four (4) speakers with the impedance between 4 Ohms to 8 Ohms. An impedance load of less than 4 Ohms could damage the unit. Never bridge or combine the speaker wire outputs. When not using four speakers, use electrical tape to tape the ends of the unused speaker outputs to prevent a short circuit. Never ground the negative spea
Resumen del contenido incluido en la página 10
Using the ISO Connector 1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated. 2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit. Cut the connector; connect the colored leads of the power cord to the car battery as shown in the color code table below for speaker and power cable connections. Function Location Connector A Connector B 1 Rea
Resumen del contenido incluido en la página 11
Panel controls Front panel 1. NEXT/PREV button 2. CLK button 3. RELEASE button 4. MOD button 5. LUD button 6. MUT button 7. 1/PAU button 8. 2/INT button 9. 3/RPT button 10. 4/RDM button 11. 5/DN10 button 16. MON button 12. 6/UP10 button 17. F/PS button 13. EJECT button 18. VOL knob 14. D slot 19. BND button 15. LCD display 20. POWER button Back of the front panel 1. Disc loading slot 2. Connector 3. RESET butt
Resumen del contenido incluido en la página 12
General operations Turning On/Off Press any button to turn the unit on, the display will show a message “WELCOME” to indicate it is ready to use. Press and hold POWER button to turn the unit off. Mode selection Press MOD button to switch between AUX, Radio and CD play mode. Volume control The volume level can be adjusted by rotating VOL knob in any mode. LOUD mode Press LUD button to emphasize the bass output, the word “LOUD ON” on the display indicates that the loudness function is on. Press th
Resumen del contenido incluido en la página 13
The clock can be set anytime when the power is on. Press CLK button and then press and hold CLK button for 3 seconds, the time will blink on the display. 1. Rotate VOL knob clockwise to adjust the hour. 2. Rotate VOL knob anti-clockwise to adjust the minute. 3. Press CLK button again or leave the unit idle for new setting to take effect. Press CLK button anytime to view the time display. DSP mode Press and hold VOL knob for 2 seconds, the display will show DSP OFF. Rotate VOL knob to select DSP
Resumen del contenido incluido en la página 14
Radio operations Choose Radio Band Press BND button to activate the Radio mode (even when CD is playing). The unit is equipped with 3 FM bands (FM1, FM2 and FM3) and 2 MW bands (MW1 and MW2). Each of the bands can store up to 6 preset stations, making total 30 preset memory stations. Radio Tune/Seek Function In Radio mode, press PREV/NEXT button to manually adjust the radio frequency. Auto seek modes Press and hold VOL knob until “DSP OFF” is shown on the display, then press VOL knob to cycle th
Resumen del contenido incluido en la página 15
press and hold F/PS button for more than 3 seconds. The receiver will automatically scan and save stations for that AM bands. 2. Scan saved stations: press F/PS button once to perform the scanning functions. In FM mode, press F/PS button and the stations in that FM band will be scanned; press this button in AM mode and scan that AM band stations. 16
Resumen del contenido incluido en la página 16
CD/MP3 operations Electronic Shock Protection (ESP) The electronic shock protection is ideal for driving uneven road. For MP3 discs Electronic Skip Protection for MP3 discs is a default feature. Please note that this feature supports the CDs with songs encoded by 96 Kb/s and 32000 Hz. For songs encoded in higher quality, the anti-shock duration will decrease proportionally to the file size. For CD discs Press and hold VOL knob for 2 seconds, the display will show “DSP OFF”. Press the knob again,
Resumen del contenido incluido en la página 17
Press F/PS button and the display will show “TRK SCH”. At this moment, press VOL knob so that “TRK” will blink on the display. Then rotate the knob to choose your desired track and press the knob again to confirm the selection. The selected track will be searched and play. File search Press F/PS button twice and the display will show “FILE SCH”. At this moment, press VOL knob to enter the root folder of the disc. Rotate the knob to choose a folder in the root folder, and press the knob to confir
Resumen del contenido incluido en la página 18
Repeat Press 3/RPT button to repeat the same track continuously. “RPT ON" will appear on the display. Press this button again to stop repeating. Random playback Press 4/RDM button to play all the tracks in random order. “RDM” (for MP3 disc) or “RDM ON” (for CD disc) will appear on the display. Press the button again to stop random play. ID3 tag If an MP3 file has ID3 Tag information, it will be displayed on the LCD. If there is no ID3 Tag information, nothing will show on LCD. The sequence of ID
Resumen del contenido incluido en la página 19
MP3 Overview Notes on MP3 MP3 is short for MPEG Audio Layer 3 and refers to an audio compression technology standard. This product allows playback of MP3 files on CD-ROM, CD-R or CD-RW discs. The unit can read MP3 files written in the format compliant with ISO 9660. However it does not support the MP3 data written by the method of packet write. The unit can not read an MP3 file that has a file extension other than “.mp3”. If you play a non- MP3 file that has the “.mp3” extension, you may he
Resumen del contenido incluido en la página 20
Handling discs Dirty, scratched or warped discs may cause skip ping or noise. Handle the disc only by the edges. To keep clean do not touch its surface. Discs should be stored in their cases after use to avoid scratches. Do not expose discs to direct sunlight, high humidity, high temperature or dust. Prolonged exposure to extreme temperature can wrap the disc (such as leaving the discs in your car during summertime). Do not stick or write anything on either side of disc. Sharp writing inst
