Manual de instrucciones de Audiovox MMSV58

Resumen del contenido incluido en la página 1

MMSV58

5.8" LCD SUN VISOR MONITOR
WITH MIRROR AND DOME LIGHT






Installation Guide
0

Resumen del contenido incluido en la página 2

Notice An LCD display and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD display or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD display or video monitor is used for television reception, video or DVD play, the LCD display or video monitor must be installed so that these features will only function when the vehicle is in ‘park’ or when the vehicle’s parking brake is applied. A

Resumen del contenido incluido en la página 3

MATERIALS INCLUDED IN THIS PACKAGE: 1) MMSV58 Sun Visor Video Monitor (P/N 136-3781) (1 pc) 2) Monitor Mounting Shroud (P/N 1024053) (1pc) 3) Remote Control (P/N 136-B3696) (1pc) 4) Hardware Package:- • M2.5 x # 8” Screws (4 pcs) • Rubber Screw Plug Caps ((138-1324) (4 pcs) 5) 7 Pin Power Wire Harness (P/N1123455) (1 pc) GROUND ACTIVATED TOOLS REQUIRED: Rotary Tool Phillips Screwdriver Utility or Razor Knife or Shears Wire Strippers Upholste

Resumen del contenido incluido en la página 4

INSTALLATION NOTES • NOTE: System component installation options vary, see the individual owner’s manuals for each component in your system to obtain a full understanding of each component’s operation. • NOTE: Each vehicle is different. Your specific disassembly and reassembly may vary slightly from the installation guide shown. INSTALLING THE MMSV58 1. Remove the Sun Visor from the vehicle. With Illuminated Vanity Mirror • Remove visor attaching hardware (screw) and set aside

Resumen del contenido incluido en la página 5

2. Remove all accessories from the visor such as mirror/door/light assemblies, etc (if applicable) and set aside for re-assembly. Figure 3. Sun Visor With All Accessories Removed 3. Once all accessories are removed, check the dimensions and material depth of the sun visor to estimate the fit for your application. NOTE: If the visor had no accessories to remove and does not have a open cavity, measure the thickness of the visor material between the rigid material in the center and

Resumen del contenido incluido en la página 6

5. Using a Razor Knife cut an “X” through the material. Figure 5. Cutting The Visor Material 6. Peel back the 4 flaps. Carefully cut out the plastic of the visor using a rotary tool. Be sure that the tool does not grab the fabric/leather or damage may occur to the material. Lay the 4 flaps back into the visor cavity. 7. Push the power/signal harness connector thru the back of the shroud and press the shroud in the visor cavity. NOTE: The cavity may require some grinding using a ro

Resumen del contenido incluido en la página 7

Figure 7. Installing The Monitor Shroud 10. Snap the screen into the visor mounting shroud Screw the screen to the visor mounting shroud using the 4 screws (supplied). 11. Install the 4 screw caps (supplied) in the holes on the 4 corners of the assembly. Figure 8. Installing The Monitor 12. Reinstall the sun visor in its original position using the attaching hardware removed in step 1. of this installation procedure. 13. Route the power/signal harness from the sun vi

Resumen del contenido incluido en la página 8

WIRING GROUND ACTIVATED Figure 9. Power/Signal Harness Emergency MMSV58 Brake Switch Power Source Vehicle Ground Video Source VCP (VIDEO 1) DVD (VIDEO 2) Figure 10. Typical System Installation 7

Resumen del contenido incluido en la página 9

TROUBLESHOOTING Symptom: Remedy: No power at Video Monitor -Verify +12 VDC on Red wire at 7 pin Harness behind video monitor. Verify ground connection with continuity test from known good ground to black wire at 7 pin Harness -Verify that the correct source is selected (i.e.: 1,2,3 or 4). Power but no video or sound Verify that the source is on and playing a known good media (such as a videotape). Verify connections at both ends of the source component harness. Verify

Resumen del contenido incluido en la página 10

© Copyright 2004 AEC 150 Marcus Blvd. Hauppauge, NY 11788 128-7158 9