Resumen del contenido incluido en la página 1
CIGE9 Extractors
Manual for Installation, Use and Maintenance
Passionate about style
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
Resumen del contenido incluido en la página 2
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment. This appliance is not designed to be used by people (including children) with reduced physical, sensorial or mental capacity, or who lack experience or knowledge about it,
Resumen del contenido incluido en la página 3
Using your Extractor For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for approximately 15 minutes after the end of cooking. A - Light switch B - Power indicator light C - Power switch A B C A1 A2 C1 C3 C2 C4 Fig. 1 To switch the extractor light on or off • Slide the light switch to position A1 for off, or A2 for on. To switch on the extractor, or change the motor speed • Slide the power switch to the position required dependent
Resumen del contenido incluido en la página 4
Care and Maintenance IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. Cleaning You should use a non-abrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. You can clean you extractor effectively by simply using a dilute solution of water and mild detergent and drying to a Fig. 2 shine with a clean cloth, for example the CDA E-Cloth. Cleaning the gre
Resumen del contenido incluido en la página 5
Changing the Light IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. DO NOT CHANGE THE LIGHT BULB IMMEDIATELY AFTER USE AS THE BULB WILL BE HOT. ALLOW IT TO COOL BEFORE REMOVING IT. 1. Remove the grease filters as described above. 2. Remove the faulty light bulb and replace with a light bulb no more powerful than that specified on the rating plate. 3. Replace the grease filters. Do not touch bulbs or adjac
Resumen del contenido incluido en la página 6
Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSED SPUR OUTLET AND PROTECTED BY A 3A FUSE. We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations. DOUBLE POLE SWITCHED The wires in the mains lead of this appliance are coloured in accordance with the FUSED SPUR OUTLET following
Resumen del contenido incluido en la página 7
Installation IMPORTANT: The extractor is intended to be mounted directly to the ceiling using fixings appropriate for the ceiling. 540 – 820mm Ensure that there is adequate ceiling strength and supports at the fixing points; if in doubt, consult a joiner or electrician. Mounting Your Extractor: When the extractor is to be installed above an electric hob, the minimum distance between the hob and extractor must exceed 600mm (650mm is recommended) When the extractor is to be mounted above a g
Resumen del contenido incluido en la página 8
Installation To fix your extractor to the ceiling, proceed as follows 1. Mark the fixing positions of the wall plugs that will be used to secure your extractor to the ceiling, as shown in 191 fig. 4 2. Drill 4 holes and insert the wallplugs, ensuring that they are suitable for use with your ceiling. If the extractor is to 203 be fixed directly to ceiling joists then wall plugs may not Fig.4 be required. 3. Fit the vent adaptor (G) to the body of the extractor, using the 2 self-
Resumen del contenido incluido en la página 9
8
Resumen del contenido incluido en la página 10
9
Resumen del contenido incluido en la página 11
10
Resumen del contenido incluido en la página 12
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
