Manual de instrucciones de Oreck XL2400RS

Resumen del contenido incluido en la página 1

®
S I M P L Y AMAZING
USA: 1-800-989-3535

CANADA: 1-888-676-7325
COMMERCIAL: 1-800-242-1378

www.oreck.com
www.oreckcommercial.com
USER’S GUIDE

VISIT ONE OF OUR OVER
450 STORE LOCATIONS

XL2400RS
HIGH SPEED UPRIGHT VACUUM
CLEANER WITH
®
VISIT ONE OF OUR OVER
450 STORE LOCATIONS
USA: 1-800-989-4244
CANADA: 1-800-393-8801
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLET!
Includes:
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagnosis
• Accessories
Other Or

Resumen del contenido incluido en la página 2

IMPORTANT BEFORE OPERATING SAFETY INSTRUCTIONS CLEANER, READ ALL When using an electrical appliance, basic INSTRUCTIONS IN THIS precautions should always be followed, including the following: MANUAL CAREFULLY. READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire, Table of Contents electric shock, or injury: • Do not leave appliance unattended when plugged in. Unplug from outlet when not in use and before servicing. Important Safety Instructio

Resumen del contenido incluido en la página 3

Maintenance and ACCESSORIES Customer Service SOLD SEPARATELY USA: 1-800-989-3535 CANADA: 1-888-676-7325 Your ORECK vacuum cleaner is a product of precise engineering. The motor bearings are permanently lubricated and should not be ITEM PART NUMBER oiled. If you require additional information or have problems with your ORECK appliance, you may call ORECK customer service at: - - 1. Dust Bag, 8 Pack In USA 1800989-3535 Regular CCPK8 In Canada 1-888-676-7325 2. Dust Bag, 8 Pack ®

Resumen del contenido incluido en la página 4

Upper 4 5 1 2 3 Handle 8 9 6 7 PRESS UNTIL SNAP IS HEARD ENFONCEZ JUSQU’À ENTENDRE UN BRUIT PRESIONE HAST A ESCUCHAR UN CHASQUIDO DE SUJECI ÓN fig. 1 Before assembling appliance, remove two screws To Replace Filter from the connector assembly. Remove cardboard insert by pulling upward. Dust Bag fig. 2 Slide upper handle section over matching section of the connector assembly. Insert short screw into WARNING: Unplug cord from electric

Resumen del contenido incluido en la página 5

Operating Instructions To Operate All paper dust bags are not the same. Your ORECK Make sure disposable paper filter dust bag is in place. DO disposable dust bags have been designed to be used with NOT operate the cleaner without a paper filter dust bag. the ORECK cleaner. Using bags other than genuine ORECK Type CC disposable bags will affect the cleaning ability of Plug the power cord into an electrical outlet and press the your cleaner and could cause damage to i

Resumen del contenido incluido en la página 6

How to Replace a Worn Belt To Adjust or Replace Brush WARNING: Unplug cord from WARNING: Unplug cord from electrical outlet before servicing. electrical outlet before servicing. Remove the replacement To determine if the brush is belt from the storage worn, place a firm straight channel. edge across the nozzle opening. If brush bristles do not extend beyond baseplate, brush should be adjusted. Remove the baseplate by Remove the door by removing 5 screws. Then, removing the hold down re

Resumen del contenido incluido en la página 7

5. Many times blockage occurs F Stuffing or Blockage due to a full dust bag causing dirt to back down Connector the air flow system. When Deflector Under certain conditions it is possible to stuff or block the intake Opening that happens, the blockage tube and the lower tube assembly. If your vacuum cleaner does will be at the top of the not pick up properly, or makes unusual noise and the outer bag system, starting in the area does not fluff up or balloon open, follow the follo

Resumen del contenido incluido en la página 8

Troubleshooting Guide WARNING: Unplug cord from electrical outlet before servicing. SAVE SERVICE CALLS...CHECK THESE FIRST: • Is the disposable filter dust bag full? • Are pores of filter dust bag clogged with powder or fine dust? • Is anything clogging the revolving brush, lower tube, intake opening, fan housing or connector assembly opening? • Is the belt in place and turning the brush? • Are the brush ends in the proper location? • Does the brush turn freely? Are hair, string or