Resumen del contenido incluido en la página 1
INSTRUCTION MANUAL
TURBINE POWERHEAD
FOR
P/N 7160, 7161 & T210
HAND HELD
TURBINE
POWERHEAD
FOR
P/N 6970g, 6971g
& 6972g
These Turbine Powerheads have been carefully designed and manufactured for long life, reliable performance
and convenient cleaning. They are designed to do most of the cleaning work for you. They move easily and do
not require downward pressure for thorough cleaning.
As with any tool with moving parts, caution must be exercised while using these Turbine Powerheads. Please
read
Resumen del contenido incluido en la página 2
INSTRUCTIONS FOR TURBINE POWERHEAD (A) ATTACHING THE TURBINE POWERHEAD To attach your metal wand, simply twist into Powerhead elbow until it fits snugly. The built-in, locking mechanism will prevent the wand from coming loose from your Powerhead while in use. To detach wand, depress tab on side of elbow and twist wand free. (See Fig. 1) The wand can be locked in an upright position by pushing it forward until the lock is engaged. (See Fig. 2). This locked position is convenient for storage and f
Resumen del contenido incluido en la página 3
(E) REMOVING THE DRIVE BELT AND BRUSH “It is recommended this procedure be performed by a Qualified Service Technician.” Should the drive belt or brush become clogged with debris or need replacing: 1. Turn off vacuum system and disconnect powerhead. 2. Remove belt cover as described in procedure C. 3. Remove the 3 screws securing the metal baseplate. (see Fig. 4) 4. Lift front of baseplate up from bumper, then pull baseplate free of unit. 5. Stubborn debris may now be easily removed from the bru
Resumen del contenido incluido en la página 4
Page 4
Resumen del contenido incluido en la página 5
INSTRUCTIONS FOR HAND HELD TURBINE POWERHEAD (A) ATTACHING THE HAND HELD TURBINE POWERHEAD To attach your metal wand and/or curved hose handle simply twist into hand brush neck until it fits snugly. (See Fig. 1). To detach wand or curved hose handle, simply hold neck of Hand Held Powerhead and pull apart with a twisting motion. (B) OPERATING PROCEDURES Your hand held Turbine Powerhead has no on/off switch. Whenever it is attached to an operating vacuum system, it will be running. There is only
Resumen del contenido incluido en la página 6
(E) BELT REPLACEMENT Remove brown base plate and belt cover (right side of Powerhead) by removing screw. (See Fig. 4). Next, remove belt from pulley (may help to turn cleaning brush backwards slightly.) (See Fig. 5). Pull belt and brush assembly out and replace belt. Before replacing base plate and belt cover, make sure a “2” is showing at both ends of brush assembly (this number is stamped right on the bearing housing.) (See Fig. 6). Make sure also that no brush bristles are caught between the
Resumen del contenido incluido en la página 7
OTHER REPAIRS For repairs or service beyond those described above, please contact your servicing distributor or dealer. LIMITED WARRANTY H-P PRODUCTS, INC. warrants that the turbine powerhead and the hand held turbine powerhead, when used for household purposes, pursuant to Seller’s instructions, will be free from defects in materials and workman- ship for a period of one year from the date of the initial consumer purchase. H-P PRODUCTS, INC. warrants that the turbine powerhead or the hand held
Resumen del contenido incluido en la página 8
Part Number Turbine Powerhead Item Part Description 7160 7161 T210 1Lower Housing 7211-01 SAME 7211-02 2 Wheel (2) 7212-01 SAME 7212-02 3 SA Turbine 7213 SAME SAME 4 Belt Cover 7214 SAME SAME 5 Base Plate 7215 SAME SAME 6 Compr. Spring 5958 SAME SAME 7Washer 5974 SAME SAME 8Washer, Elbow Seal 5971 SAME SAME 9 Elbow 7216-01 SAME 7216-02 10 Spring, Wand 5966 SAME SAME 11 Retainer/Cap 7217-01 SAME 7217-02 12 Spring, Latch 7218 SAME SAME 13 SA Tophousing 7219 7220 7221 14 Bumper 7222-01 SAME 7222-02
Resumen del contenido incluido en la página 9
Page 9
Resumen del contenido incluido en la página 10
HAND HELD TURBINE POWERHEAD Item No. Description 1 Swivel 6321-1 2 Sub Assembly 6322 Turbine and Shaft 3 Belt 6323 4 Swivel Seal (2 req.) 6324 5 Latch Spring 6325 6 Latch 6326-1 7 Housing, Assy. Half 6780-1 8 Label 7054 9 Slide Valve 6328-1 10 Sub Assy. Housing, Half/Belt Side 6757-1 11 Belt Cover 6330-1 12 Screw 6-19x.750 (3 req.) 6331 13 Brush Assembly 6332 14 Base Plate with Basket and Bumper 6755 15 Basket 6334 (Avail. only with #6755) 16 Bumper 6335 17 Screw 6-19x1.2 (1 req.) 6336 18 Cautio
