Resumen del contenido incluido en la página 1
ViewSonic by Premier Mounts
INSTALLATION INSTRUCTIONS
WMK-027
Universal Short Throw Wall Mount
EUROPE
NORTH AMERICA
3130 East Miraloma Avenue
Swallow House,
Anaheim, CA 92806 USA
Shilton Industrial Estate,
USA and Canada –
Shilton, Coventry, England CV79JY
Phone: 800-368-9700
Phone: +44 (0) 2476 614700
Fax: 800-832-4888
Fax: +44 (0) 2476 614710
Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044
©Premier Mounts 2009
9530-070-353-00
Resumen del contenido incluido en la página 2
WMK-027 Table of Contents Warning Statements 2 Parts List 3 Installation Tools 3 Determining the Installation Height 4 Wood Stud Installation 5 Solid Surface Installation 6 Utilizing the Storage Feature 7 Attaching the Projector Arm 7 Throw Distance Calculation 8 Upper Mounting Bracket Installation 9 Extension Arm Installation 10 Base Box Installation 10 Cable Managem
Resumen del contenido incluido en la página 3
WMK-027 Parts List This mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts (800) 368-9700. Extension Hardware Pack M6 x 12mm Security (Qty 2) 1/4” Flat Washer (Qty 2) 1/4” Nylon Spacer Extension Arm - Optional (Qty 1) (Qty 2) Wall Plate (Qty 1) Arm Assembly (Qty 1) included with the
Resumen del contenido incluido en la página 4
WMK-027 Determining the Installation Height In order to determine the installation height and throw distance, the PDS-PLUS projector bracket must be mounted to the projector. Please refer to the PDS-PLUS Installation Instructions prior to performing the following steps. Refer to the projectors User’s Manual to determine the offset of the projector lens to the top of the screen/whiteboard. PDS-PLUS Bracket Projector Lens Step 1. Measure distance from center of lens to the top of the PDS-PLUS bra
Resumen del contenido incluido en la página 5
WMK-027 Wood Stud Installation Do NOT over-tighten lag bolts when attaching the mount to the wall. Improper installation may result in personal injury or damage to property. DEAD CENTER MUST BE LOCATED ON THE STUD FOR CORRECT AND SAFE INSTALLATION. Wood Stud Marking Marking (from page 4) Wood Stud Stud finder Wall Plate Step 1. Use an electronic stud finder Step 2. Use a pencil to mark the first Step 3. Use the level to make sure (commercially available) to mounting hole, just above
Resumen del contenido incluido en la página 6
WMK-027 Solid Surface Installation Concrete drill bits are commercially available. Hammer Marking Drill 3/8” Drill Bit Wedge Anchor Pilot Hole Step 3. Use a 3/8” drill bit to drill the Step 1. Place the wall plate against Step 4. Once the holes have been mounting holes where the the wall and use a level to drilled, place the concrete marks were made with a make sure the wall plate is wedge anchors into the pencil. level from top to bottom. hole. Using a hammer, Step 2. U
Resumen del contenido incluido en la página 7
WMK-027 Utilizing the Storage Feature The storage feature may be used to store electronic components. There is an accessible door on each side of the storage enclosure. It may be securely held shut with the use of four (4) M5 x 12mm security head screws. It may be easiest to pre-wire all cables down the arm (or extension) at this time (see Page 11). Security Wrench M5 x 12mm Security Screw Electronic Components Electronic Components Door Door Step 1. Open the storage door that is located
Resumen del contenido incluido en la página 8
WMK-027 MAKE SURE THE PROJECTOR ARM IS FULLY SEATED BEFORE RELEASING THE UNIT. Lock Mounting Point M5 x 12mm Security Head Screw Screwdriver/Security Wrench Step 4. Locate the two (2) lock mounting points on the projector arm. These two points will be aligned with the lock mounting points on the wall plate. Step 5. Using a security wrench, insert and tighten two (2) M5 x 12mm security head screws. DO NOT OVERTIGHTEN THE SCREWS. Throw Distance Calculation Please review the Operator’s Manual th
Resumen del contenido incluido en la página 9
WMK-027 Upper Mounting Bracket Installation Step 1. Insert the inner slide plate into the projector arm. Projector Arm Step 2. Determine which adjustment slot will be best for the projector placement. Adjustment Step 3. Raise the upper mounting bracket into Slot position. Inner Slide Step 4. Align the mounting holes of the upper Plate projector plate with the mounting holes of the inner slide plate. Upper Mounting Step 5. Secure and finger-tighten two (2) Bracket M6 x 12mm se
Resumen del contenido incluido en la página 10
WMK-027 Extension Arm Installation (Optional) Please see the Operator’s Manual to determine the correct throw distance (the distance from the projector to the screen) must be determined prior to mounting the projector. If the extension arm was purchased at a later date, the end cover must be removed prior to installing the extension arm. WMK-027 1/4” Flat Washers 1/4” Nylon Spacer M6 x 12 Security Screw Security Wrench Upper Mounting Bracket Extension Arm Step 1. Slide the extension arm i
Resumen del contenido incluido en la página 11
WMK-027 Cable Management WMK-027 Electronic Components WMK-027 Electronic Components Electronic Cables Components Cable Opening Cable Opening Projector Hook-Ups Cables Cable Opening Projector Hook-Ups Step 1. The cable access holes are located at the end of the short throw mount and on the wall plate. Step 2. Route the cables through one end of the WMK-027 and out the other end. Set Screw Installation (Optional) The M6 set screw will be used in conjunction with any standard 1-1/2” NPT or CLS
Resumen del contenido incluido en la página 12
WMK-027 Technical Specifications All measurements are in inches(mm). Page 12 Installation Instructions
Resumen del contenido incluido en la página 13
WMK-027 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.
