Manual de instrucciones de Diamond D662

Resumen del contenido incluido en la página 1

CONVERTIBLE SPEAKER
INSTALLATION MANUAL
D652 D662
|

Resumen del contenido incluido en la página 2

SPECIAL THANKS Dear Valued Customer, Thank you for choosing Diamond Audio D6 speakers. These speakers represent the latest advances in acoustic technology, and like all Diamond Audio products, are hand built and tested using the highest grade components and state of the art techniques. When installed properly, they will provide many years of accurate sound reproduction. Please keep in mind that prolonged exposure to sound pressure levels in excess of 100 dB can cause permanent hearing loss.

Resumen del contenido incluido en la página 3

D6 CONVERTIBLE SPEAKER SYSTEMS FEATURES CONVERTIBILITY • Hard Annodized Aluminum Cone Your new D6 speaker system has the unique ability to • Rubber Surround be used as either a component or a coaxial speaker. • High Density Proprietary Composite Frame Depending on your installation requirements, the tweeter • Flat Progressive Spider can be installed separately or mounted directly to the • Inductively Controlled Motor Design midbass/midrange unit with the supplied kit. This • Rubber Boot M

Resumen del contenido incluido en la página 4

MIDBASS SPEAKER MOUNTING The following illustrations show the parts included and correct mounting assembly of the D6 midbass speaker and tweeter. The grill on the midbass is optional. Parts List (2) D6 Component Midbass/Midrange Speakers (2) D6 Component Tweeters (2) D6 Grills w/ Mounting Ring (2) Mounting Gaskets (1) Mounting Hardware Kit Screw Clips Gasket Mounting Screws Mid-bass Driver Grill 4 ©2008 Diamond Audio Technologies. All rights reserved.

Resumen del contenido incluido en la página 5

Mounting Cup Spring Clip Tweeter Tweeter Mounting When flush or surface mounting tweeters, make sure the desired location can accommodate the hole size and depth required. Mount the cup using provided hardware (flush mount illustration shown on right.) Mount surface cup at desired angle with provided screws in tweeter mounting kit. Snake speaker wires through tweeter cup, connect tweeter to wires, and snap tweeter into cup by aligning the notches. Be careful not to push on the center of the

Resumen del contenido incluido en la página 6

COMPONENT SYSTEM CONNECTION The illustration below shows how to connect one channel of the D6 component system. Mid-bass Driver Crossover Tweeter Optional RAF Amplifier THIELE/SMALL PARAMETERS Parameter (unit) D652 D662 S.0ta S.0ts Sensitivity 87.4 87.2 92 91 Qts 0.5 0.82 0.54 0.65 Fs (Hz) 57.8 60.0 1650 1520 Vas (L) 11.0 15.6 n/a n/a Re (ohm) 3.6 3.62 5.6 5.6 Xmax (mm) 3.6 4.8 n/a n/a Impedance (ohm) 4 4 8 8 Power (Watts) Nom/Max 60/120 75/150 50/100 50/100 6 ©2008 Diamond Audio Technologies. A

Resumen del contenido incluido en la página 7

PHYSICAL DIMENSIONS Dimension D652 D662 S.0ta/s Total Diameter (A) 5.57” (141.6mm) 6.50” (165.4mm) 1.9 (48.26mm) Mounting Diameter (B) 4.60” (117.3mm) 5.50” (140.6mm) 1.64 (41.65mm) Screw Hole Diameter (C) 5.23” (133mm) 6.14” (156mm) N/A Mounting Depth (D) 2.16” (55mm) 2.32” (59mm) 0.5 (12.7mm) Magnet Diameter (E) 3.07” (78mm) 3.40” (86.4mm) N/A 7 ©2008 Diamond Audio Technologies. All rights reserved.

Resumen del contenido incluido en la página 8

LIMITED SPEAKER WARRANTY STATEMENT Diamond Audio Technologies, LLC (DAT) warrants this product to be free from defects in material and workmanship for a period of one (1) year from the original date of purchase provided it was purchased from an authorized DAT retailer within the United States. However, if this product was installed by the authorized DAT retailer, the warranty period will be extended to three (3) years. THIS WARRANTY IS NOT TRANSFERABLE AND APPLIES ONLY TO THE ORIGINAL PURCHAS