Manual de instrucciones de Audiovox CE-100

Resumen del contenido incluido en la página 1

IMPORTANT- This system is designed for Univenal Installation of many different Manufacturen equipment. When
required, specific instructions or templates included in this package are provided when the Universal Mounting Method is
not applicable.
I. Selection of the Mounting Area
Note: Specific templates are included for J.I. Case Model 580K equipment. Use universal template for John Deere, Caterpillar,
Fiatallis and other manufacturers.
A. This product is designed for overhead (roof) mounting in

Resumen del contenido incluido en la página 2

Fig. 1 Installation I. Use universal template provided and locate on roof the desired mounting area. Observe cautions for possible interference in headliner or steel roof. 2. Drill two 5/16" dia. holes through the fiberglass roof cap, the steel roof and headliner making certain the drill is 900 to the roof. 3. Enlarge the 5/16" holes in the fiberglass roof to 1 3/8" dia. Warning -Only enlarge the two holes in the roof cap. Do not enlarge the holes in the steel roof or headliner. 4. Remove the in

Resumen del contenido incluido en la página 3

FIG. A FIBERGLASS CAP ROOF ( CROSS SECTION OF ROOF) RBERGLASS ROOF CAP STEEL ROOF :":,.:;:c;:;:;c:;,,;;.:c:.:'ii:::i FIG. A DISASSEMBLY: AIR GAP 1. Remove molded inside headliner prior to installation AIR GAP 2. Do not remove the fiberglass roof cap See F1g. 1. for Installation LMOLDED HEADLINER FIG. B STEEL ROOF WITH HEADLINER {CROSS SECTION OF ROOF) FIG. B DISASSEMBLY: 1. Remove molded inside headliner prior to installation Note: If the air gap (space) between the steel roof and the headliner

Resumen del contenido incluido en la página 4

FIG. 1. INSTALLATION , (INSERT AFTER ""' INSTALLATION IS WRENCH (INCLUDED) - COMPLETED) USE I SEALANT TO INSURE ~ A LEAK-FREE SEAL / / ~ ~ / STEEL CUP WASHERS I MOUNTING BOLT (SELECT LENGTH """" NEEDE FROM CHOICE OF LENGTHS ,..,.. INCLUDED) I --- DRILL 5/16. /r~MMEIS DIA. HOLES PER ~ - TEMPLATE -;--- -- APPLY A BEAD OF SEALANT AROUND / -- BOTH SIDES / OF HOLES ~ FLAT WASHERS ~..- JAM NUTS (TIGHTEN ARMLY) ~ STEEL PLATE ~~ I ~ USE THESE HOLES FOR CASE 580K / ./ USE THESE HOLES / ~ FOR ALL OTHER EQ

Resumen del contenido incluido en la página 5

Resumen del contenido incluido en la página 6

FIG. 3 INSTALLATION WRENCH (INCLUDED) ~ / STEEL CUP WASHERS MOUNTING BOLT (SELECT LENGTH ' NEEDE INCLUDED) FROM CHOICE OF LENGTHS I G RUBBER GROMMETS ~ DRILL 5/16" I DIA. HOLES PER TEMPLATE ~ APPLY A BEAD OF SEALANT ~ FLAT WASHERS AROUND BOTH SIDES ~ - ,,) OF HOLES ~..- JAM NUTS (TIGHTEN RRMLY) ~ ~ ~ ~ ~c STEEL PLATE ~ ~ ~ ~~ ---: J --:-:"" USE THESE HOLES FOR CASE 580K ~ USE THESE HOLES / FOR ALL OTHER EQUIPMENT ~~ BLACK WASHERS (6 PCS.) #6 BLACK SCREWS TRIMPLATE (6 PCS.) PLASTIC HOUSING 0 0~ R

Resumen del contenido incluido en la página 7

Resumen del contenido incluido en la página 8

Cab Wiring I. Route pre-installed antenna lead to mounting plate for connection to radio later in installation. 2. Locate the two wire (Red and Black) harness and the single Green/White stripe harness in this kit. 3. Connect the Black wire to vehicle ground using the crimp-on ring terminal and screw included. 4. Splice the Red wire to any + 12 volt accessory wire in the cab using the quick splice included. 5. Splice the Green /White stripe wire to any + 12 volt battery source in the cab using th