Manual de instrucciones de Electrolux Mini Trim MT21

Resumen del contenido incluido en la página 1

MT21
For all customer enquiries or for replacement parts, contact:-
☎ ☎
01325 300303
www.flymo.com
eop.customer.services@electrolux.co.uk
IMPORTANT INFORMATION
Read before use
& retain for future reference

Resumen del contenido incluido en la página 2

360º 1 Carton Contents Mini Trim/MT21/ Mini Trim Auto + Switch Lever Switch Lever Mini Trim Auto Steady Handle Upper Shaft Upper Shaft Electric Cable with moulded on plug Electric Cable with moulded on plug Lower Lower Shaft Guard Shaft Guard Instruction Instruction Manual Manual IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new product. IF ANY PARTS ARE MISSING CONTACT:- Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300

Resumen del contenido incluido en la página 3

2 4. Immediately disconnect from the mains electricity 2. Avoid operating your trimmer in wet grass, where supply if the cable is cut, or the insulation is dam- feasible. aged. Do not touch the electric cable until the elec- 3. Take care in wet grass, you may lose your footing. trical supply has been disconnected. Do not repair 4. On slopes, be extra careful of your footing and wear a cut or damaged cable. Replace it with a new non-slip footwear. one. 5. Do not walk backwards when trimming,

Resumen del contenido incluido en la página 4

3 Assembly Instructions A 1 Shaft Assembly (A) 1. Locate the lower shaft (A1) into the upper shaft (A2). 2. Grasp firmly and hold steady the lower shaft. Locate 2 the upper shaft and snap together firmly. • The unit is correctly assembled when the gap between the upper and lower shaft has been closed. 1 2 Mini Trim/MT21 Mini Trim Auto/ B Auto + 1 1 Safety Guard Assembly (B) & (C) 1. Locate the safety guard (B1) over the cutting head (B2). Ensure the nylon line is fed through the hole in the sa

Resumen del contenido incluido en la página 5

4 Manual Line Feed System To feed the nylon line H 1. Press and hold the two latches (H). 2. Gently pull the line until it reaches the line cutter. 3. Release the two latches. Check that the spool is locked in position. 4. If too much line has been fed out, press the two latches and turn the spool anti-clockwise until the line is at the desired length. To remove spool 1. Press and hold the two latches. 2. Pull spool out of spoolholder (J). When refitting the spool 1. Keep all areas of the spool

Resumen del contenido incluido en la página 6

5 Automatic Line Feed System How the automatic line feed works (M) M 1. When initially switching on the trimmer, a small length of line is fed out. 2. A ‘clattering’ noise will be heard when the nylon line hits the line cutter. DO NOT BE ALARMED this is quite normal. After approximately 5 seconds the line will be cut to the correct length and the noise will reduce as the motor reaches full speed. • Make sure the motor is up to full speed before trimming. 3. If the noise of the nylon line bein

Resumen del contenido incluido en la página 7

6 Fault Finding Chart (Automatic Line Feed only) WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment. FAULT CHECK ACTION Is the automatic line feed work- Manually feed out line. No LINE NOT FEEDING ing? OR Is the line fed out and visible? Remove cap and spool, free line LINE TOO SHORT Has line been removed from No and re-fit spool and cap. OR cleat? TRIMMER VIBRATES The line may be jammed on the Is the manual line feed working? No spool. Rewind

Resumen del contenido incluido en la página 8

Guarantee & Guarantee Policy If any part is found to be defective due to faulty manufacture Failures due to the following are not covered, therefore it is important that within the guarantee period, Electrolux Outdoor Products, you read the instructions contained in this Operator's Manual and under- through its Authorised Service Repairers will effect the repair or stand how to operate and maintain your machine: replacement to the customer free of charge providing: Failures not covered by guaran