Resumen del contenido incluido en la página 1
245ix
246ix
owner's manual
analog and digital systems
Resumen del contenido incluido en la página 2
table of contents introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 about this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 ins
Resumen del contenido incluido en la página 3
features Molded woofer basket - The backbone of any good woofer is its basket. It provides the proper alignment and support structure for the magnet and moving parts while the very thin braces guarantee a minimum of early reflections off the basket that would be ordinarily transmitted as sonic colorations through the cone. Woofer cone - Anodized polypropylene provides the right combination of rigidity and low moving mass for low distortion and excellent frequency response. Vented voice coil - Ma
Resumen del contenido incluido en la página 4
When removing or installing the grilles, be careful not to brush the woofer's rubber surround or the tweeter's dome with the edge of the grille. Cutting or tearing the surround or dome will destroy the unit. Never run wires outside or beneath the vehicle where they can be snagged by road hazards or the moving parts of the vehicle. Use existing wire channels, sills, panels and molding strips inside the automobile to hide the wiring for neat appearance and safety. Make sure your radio/cassette/cd
Resumen del contenido incluido en la página 5
crossover features and connections Tweeter Thermal Breaker -3, 0, +3 Tweeter DC Clip Protection Tweeter Level (dB) Switch Bi-amp–Parallel Tweeter Phase Switch Switch Bi-amp Parallel 180° 0° IN OUT Woofer Tweeter Woofer Tweeter + - + - + - + - Bi-amp/Parallel switch Select the Bi-amp position if you intend on driving the woofers and tweeters with separate amplifiers (four channels). Select the Parallel position if you intend on driving the woofers and tweeters w
Resumen del contenido incluido en la página 6
You may also Bi-wire the system by connecting the woofer input terminals to the amplifier and connect ing the tweeter input terminals to the same amplifier with another set of speaker wires. This is sometimes done to allow a specific high frequency or low frequency cabling to be used for the two separate signal paths. See Crossover Installation for additional information on bi-wiring. Be sure to connect the positive crossover terminals to the positive speaker terminals and positive amplifier ter
Resumen del contenido incluido en la página 7
speaker installation Woofer installation The woofer will fit into many standard factory mounting locations using the existing mounting holes in the automobile. Remove the trim panels and inspect the installation locations before you cut and drill the holes required to mount the woofer. Removing the panel will also make it much easier to route wiring inside the door. Look for original equipment speaker installation cutouts that can be used to install the woofers with little or no modifications. U
Resumen del contenido incluido en la página 8
Resumen del contenido incluido en la página 9
Resumen del contenido incluido en la página 10
Check the intended installation site to be sure that there is sufficient depth behind the Metal mounting bracket mounting surface for the rear cup and mounting screws. The minimum depth required behind the back of the mounting surface is 1" Mounting slots (qty 4) (25 mm). The front cup mounts into the mounting through a 1-7/8" (48 mm) diameter hole. Be careful that the hole does not exceed 2-1/8" (55 mm) diameter at any point so that M4-0.7 x 4-1/2 cm the rim of the cup will completely cover the
Resumen del contenido incluido en la página 11
Tweeter Bolts Panel Bracket Tweeter Flush Mount Wiring Wire Housing NOTE: The tweeter grill can be easily removed for coaxial applications, or to facilitate mounting the tweeter behind an existing factory grill. Use the supplied black butyl material to attach the tweeter grill for all other applications. crossover installation The system supports conventional wiring, Bi-wiring or Bi-amping using the supplied passive crossovers. While conventional (parallel mode) wiring will provide excellent sou
Resumen del contenido incluido en la página 12
Resumen del contenido incluido en la página 13
bi-amplified connections to crossover Connections from the crossover to the woofer and tweeter are the same as the normal wiring method. Connect the amplifier you have chosen for the tweeter to the “Tweeter In” terminals input. Connect the woofer amplifier to the “Woofer In” terminals. NOTE: You must move the selectable switch to the Bi-amp position. Failure to set the switch correctly may cause damage to the amplifiers or the crossover. Bi-Amplified (Switch in Bi-amp Position) Tweeter Bi-amp P
Resumen del contenido incluido en la página 14
bi-wire connections to crossover Connections from the crossover to the woofer and tweeter are the same as the normal wiring method. Connect the amplifier to the tweeter input terminals with one run of wire. Connect the amplifier to the woofer input terminals with another run of wire. NOTE: You must move the selectable switch to the parallel position. Failure to set the switch correctly will not damage the equipment, but could interfere with any enhancement of the sound due to bi-wiring. Bi-Wired
Resumen del contenido incluido en la página 15
Resumen del contenido incluido en la página 16
specifications 245ix 246ix Frequency response 90Hz–22kHz 70Hz–22kHz Sensitivity 91dB 91dB Impedance 4 ohms 4 ohms Recommended amplifier power 45–100 watts 45–150 watts Mounting depth (woofer) 2-1/2 inches (6.35 cm) 2-5/8 inches (6.67 cm) RMSE-free 1.18 ohms 0.54 ohms Fs 95.85 Hz 78.08 Hz Re 3.80 ohms 3.85 ohms Res 24.85 ohms 28.55 ohms Qms 5.54 5.70 Qes 0.85 0.77 Qts 0.73 0.68 L1 0.27 mH 0.28 mH L2 0.39 mH 0.42 mH R2 4.01 ohms 3.58 ohms Vas (Sd) 2.53 liters 5.61 liters Mms 11.46 grams 12.66 gram
Resumen del contenido incluido en la página 17
warranty information LIMITED TWO YEAR CONSUMER WARRANTY Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be defective in workmanship or material under normal use, for a period of two years from the date of purchase from the dealer as indicated by the date code marking of the product PROVIDED the product was installed by an authorized Directed dealer. During this two-year period, there will be no charge for this replacement PROVIDED the uni
Resumen del contenido incluido en la página 18
