Resumen del contenido incluido en la página 1
334im
335im
336im
PN# 319-1063 rev A 5/99
Resumen del contenido incluido en la página 2
declaration of conformity manufacturer’s name: analog and digital systems, inc manufacturer’s address: 300 wildwood avenue woburn, ma 01801 usa declares, that the product: product name: 334im 335im 336im conforms to the following standards: EN 50 081-1/1992 EN 50 082-1/3.1995 european contact: Axel Perlwitz audiomax GmbH Heilbronn Germany 2 19
Resumen del contenido incluido en la página 3
table of contents introduction........................................................................................3 about this manual..................................................................................3 features of your 3-series loudspeaker...............................................................4 warnings and tips..................................................................................5 system planning.............................................................
Resumen del contenido incluido en la página 4
features of your 3-series loudspeaker warranty information There are two things you must do to ensure trouble free service in the event you need warranty repairs. molded woofer basket - the back bone of any good woofer is it’s basket. It provides the 1 - Keep your original sales receipt in a safe place. A copy of the receipt will be required to obtain warranty service. proper alignment and support structure for the magnet while the very thin braces guarantee a 2 - Be sure your retail dealer has
Resumen del contenido incluido en la página 5
warnings and tips jack pinouts Study your automobile thoroughly before you drill or cut any holes. Take extra care when working near gas tanks, gas lines, brake or hydraulic lines and electrical wiring. Wear eye and ear protection when using power tools. Keep the woofers and tweeters away from metal filings and shavings. Once foreign objects are stuck to the magnets or tweeter dome, it will be virtually impossible to remove them. Keep the tweeters in their protective bags until final mounting
Resumen del contenido incluido en la página 6
amplifier requirements troubleshooting symptom probable cause remedy no output source or amplifier not turned on check source or amplifier and fix as a note on power handling needed Each 3-series speaker system requires a minimum of 20 Watts per channel to achieve reasonable audio input not connected or no check RCA connections and signal listening volumes in a moving automobile without clipping the amplifier. a/d/s/ recommends output from source integrity, fix or replace as needed 150 Watts per
Resumen del contenido incluido en la página 7
bi-wire connections to the crossover network midrange contour connections to the woofer and tweeter are the same as the normal wiring method. Connect the The two position switch labeled car / demo adjusts the frequency response of the midrange amplifier to the tweeter to the terminals marked tweeter input. Connect the woofer amplifier to driver. The car position is optimized for in car off axis listening. The demo position offers flat the woofer input terminals with another run of wire. freque
Resumen del contenido incluido en la página 8
termination connections to crossover network and radio or amplifier The woofer and the tweeter use .187 spade lugs for electrical connections. Use standard .187 route the wires connected to the input terminals on the front of the crossover network to the female quick disconnects to attach wires to the speaker. power amplifier (or, if you are not using a separate power amplifier, the in-dash radio/tape or CD player). Connect the wires to the amplifier outputs as recommended by the manufacturer of
Resumen del contenido incluido en la página 9
crossover installation bi-wiring / bi-amping The 3-series allows conventional wiring, bi-wiring, or bi-amping using the supplied passive crossovers. While conventional wiring will provide excellent sound, bi-wiring or bi-amping will further enhance the performance in no-compromise systems. Bi-wiring uses a separate pair of speaker wires for the high frequency and low frequency signal between an amplifier channel and its associated crossover network. This gives you the option of choosing wire wh
Resumen del contenido incluido en la página 10
rotating the tweeter Grasp the knob on the back side of the speaker, and gently turn it to the desired position. a/d/s/ recommends that you start with the tweeter angled so it points directly at the listening area. Feel free to experiment with the position that gives you the most pleasing sound quality. NOTE: this feature only applies to the 335im, and 336im. The tweeter of the 334im does not rotate. 10 11
