Manual de instrucciones de Transition Networks CSEFE10XX-10X

Resumen del contenido incluido en la página 6

CSEFE10xx-10x Contact Us Troubleshooting -- Continued Technical Support 6. Is the TP-ACT LED illuminated? Technical support is available 24 hours a day. NO US and Canada: 1-800-260-1312  Check the twisted-pair copper cables for proper connection. International: 00-1-952-941-7600  Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600. YES Transition Now  Go to step 7. Chat live via the Web with Transition Networks Technical Support. Log onto www.transition.com and click the Transiti

Resumen del contenido incluido en la página 7

Compliance Information CISPR22/EN55022 Class A + EN55024 CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructi

Resumen del contenido incluido en la página 1

User’s Guide
CSEFE10xx-10x
Slide-in-Module Media Converter
• Switchable Ethernet and Fast Ethernet
 10 Mb/s Copper to Fiber
 100 Mb/s Copper to Fiber
Transition Networks CSEFE10xx-10x series Ethernet /
Fast Ethernet media converter is designed to be
installed in a Transition Networks PointSystem™
chassis and is a 10Mbps or 100Mbps switch-selectable
media converter.
Both the copper and fiber links operate at the same speed setting via a hard set with
a dip switch, so the media converter oper

Resumen del contenido incluido en la página 2

CSEFE10xx-10x Installation Installation -- Continued CAUTION: Wear a grounding device and observe electrostatic discharge Set the Speed (switch 2) Link Pass-Through: up = Enable precautions when setting the jumper or when installing the media converter. Switch 2 sets the speed for both the twisted-pair Speed: up = 100 Mb/s Failure to observe this caution could result in damage to, and subsequent copper and fiber links: failure of, the media converter. up = copper and fiber links are at 100Mb/s.

Resumen del contenido incluido en la página 3

CSEFE10xx-10x Installation -- Continued Operation Install the Fiber Cable Status LEDs PWR The CSEFE10xx-10x is designed to be installed in pairs over the fiber link, Use the status LEDs to monitor the CSEFE10xx-10x media ACT 100 10 where one is the local media converter and the other is the remote. converter operation in the network. F 1. Locate or build fiber-optic cable with male, two-stranded TX to RX TP PWR Power On = Connection to the external AC connectors installed at both ends. TX

Resumen del contenido incluido en la página 4

CSEFE10xx-10x Operation -- Continued Cable Specifications The physical characteristics must meet or exceed IEEE 802.3™ specifications. SNMP Fiber Cable Use SNMP at an attached terminal or at a remote location to monitor the media converter by monitoring: -9 Bit Error Rate: <10  Media converter power Single mode: 9 µm  Copper link status  Fiber link status CSEFE1012-100 1310 nm single mode Fiber-optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm  Copper receive status Fiber-optic Recei

Resumen del contenido incluido en la página 5

CSEFE10xx-10x Technical Specifications Troubleshooting For use with Transition Networks Model CSEFE10xx-10x or equivalent. 1. Is the PWR LED on the media converter illuminated? Standards: IEEE 802.3™, 10Base-T, 100Base-TX, 100Base-FX NO Data Rate: 10 Mb/s, 100 Mb/s  Is the media converter inserted properly into the chassis?  Is the power cord properly installed in the chassis and in the Dimensions: 3.4" x 0.87" x 5" (86 mm x 22 mm x 182 mm) grounded AC outlet? Weight: 3 oz (91 g) (approximat