Resumen del contenido incluido en la página 1
R
NETWORK 1275 Danner Dr Tel:330-562-7070
TECHNOLOGIES Aurora, OH 44202 Fax:330-562-1999
INCORPORATED www.nti1.com
NTI
TM
VEEMUX A Series
SM-nXm-AV-LCD
Audio/Video Matrix Switch
Installation and Operation Manual
MAN063 Rev 10/1/03
Resumen del contenido incluido en la página 2
WARRANTY INFORMATION The warranty period on this product (parts and labor) is one (1) year from the date of purchase. Please contact Network Technologies Inc at (800) RGB-TECH (800-742-8324) or (330) 562-7070 for information regarding repairs and/or returns. A return authorization number is required for all repairs/returns. COPYRIGHT Copyright © 2003 by Network Technologies Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted,
Resumen del contenido incluido en la página 3
Table of Contents Introduction........................................................................................................................................................................................1 Specifications.....................................................................................................................................................................................1 Cables.................................................................................
Resumen del contenido incluido en la página 4
Introduction Introduction The SM-nXm-AV-LCD Audio/Video Matrix switch (VEEMUX-A) allows up to 32 audio/video sources (n) to be connected to up to 16 destinations (m). Different destinations can even be connected to the same source. Video resolution up to 1920x1200@85Hz is supported with no degradation – guaranteed. Stereo audio is supported, as well as volume control and separate audio/video switching. An LCD on the front panel indicates the current connections. The VEEMUX-A can be controlled by
Resumen del contenido incluido en la página 5
Ordering Inf Ordering Information ormation The SM-nXm-AV-LCD Audio/Video Matrix switch (VEEMUX-A) can be ordered in many sizes and with several control options. The base unit includes a user keypad and an RS232 port to make up a complete system, with an option for an infrared control. The infrared option is purchased separately, allowing for maximum user satisfaction in each unique configuration. The VEEMUX-A Audio/Video Matrix switch is built to a specific size ranging from 8 to 32 inputs and 2
Resumen del contenido incluido en la página 6
% ! 3
1 2
1 2
Resumen del contenido incluido en la página 7
Installation Installation 1. Turn OFF power to all video sources (inputs) that will be connected to the VEEMUX-A before connecting or disconnecting any cables. 2. For each video source, connect a VEXT-xx-MM cable from the video port of the source to a video input (VIDEO-1) of the VEEMUX-A (see Fig. 1). 3. Repeat step 2 for remaining video sources. 4. For each audio source, connect a SA-xx-MM cable from the audio source to the port labeled AUDIO IN 1. Notes: The audi
Resumen del contenido incluido en la página 8
6. Connect a monitor to the port labeled MONITOR 1 on the rear of the VEEMUX-A (see Fig. 2). 7. Repeat step 6 for remaining monitors (outputs). 8. Connect audio output device (speakers) to port labeled AUDIO OUT 1. 9. Repeat step 8 for remaining audio output devices, connecting them to any remaining AUDIO OUT ports. 10. If using RS232 control, connect the video source's serial port to the VEEMUX-A “RS232” with a DINT-xx. 11. Plug the VEEMUX-A to an AC power outlet. 12. Turn ON power to the VEE
Resumen del contenido incluido en la página 9
Front Panel Keypad Control The front panel keypad and LCD (drawing below) allow the user to view and change current audio and video connections, adjust audio volume and configure the RS-232 control interface. The keypad buttons perform the following functions. ESC Escape back to the main display. 0 – 9 Used to enter numbers. ( # )
% ! 3 OUT Specifies output port
Resumen del contenido incluido en la página 10
• Connecting video only To make a video connection without changing the current audio connection, use any of the following commands: 1. , < ▲>, Single digit output port number, or , Single digit input port number, . Ex: < ▲> 3 5 2. , < ▲>, Double digit output port number, Double digit input port number. Ex: < ▲> 03 05 All video outputs can be connected to one video input by using <*>: 1. <*>, < ▲>, Single digit input port number, Ex:
Resumen del contenido incluido en la página 11
RS232 Control RS232 Control Remote Connection The RS232 Interface is designed to control the switch via serial (RS232) daisy chain connection from any host computer or other controller with an RS232 communications port. There is, however, a restriction that must be followed: A program must be used that will send an entire command line all at once, not character by character. (The HyperTerminal program in WINDOWS cannot be used, as it sends each character one at a time.) The pin outs for the DB
Resumen del contenido incluido en la página 12
Command Protocol Host controller commands supported by the unit are defined below. All commands should be terminated with a (carriage return). When a command is sent, the entire string is echoed back to the host along with a response from the addressed unit as shown in the command definitions. All characters should be upper case, and all numbers below 10 should have a leading 0 (ex: 1 = 01). NOTE: For units with one output or user port, use 01 for the output select. RS-232 Command Protocol
Resumen del contenido incluido en la página 13
CB - Change Baud Rate For All Switches Format: CB 00,BR Successful Response: None Syntax or Transmission Error: ? Behavior: All switches on the serial bus will change their baud rate to the new baud rate. 12 specifies 1200 baud, 24 specifies 2400 baud, 48 specifies 4800 baud, 96 specifies 9600 baud. RS - Internal Reset This feature is not available in the VEEMUX-A. RV - Read NTI Version String Format: RV SW,00 Successful Response: * string Syntax or Transmission
Resumen del contenido incluido en la página 14
RO - VIDEO Read Connection For Output/User Port Format: RO SW,OP Successful Response: * IP Syntax or Transmission Error: ? Behavior: This will find out which VIDEO input/CPU port is connected to the specified VIDEO output/user port. AS - AUDIO Connect One Output/User Port To Input/CPU Port Format: AS SW,IP,OP Successful Response: * Syntax or Transmission Error: ? Behavior: This will connect a single AUDIO output/user port to a single AUDIO input/CPU port.
Resumen del contenido incluido en la página 15
AV - Set Volume Level For Output/User Port Format: AV SW,OP,VV Successful Response: * Syntax or Transmission Error: ? Behavior: On switches that support AUDIO and support volume control of the output/user port, this command will set the volume of the specified AUDIO output/user port from a scale of 00 to 99, which represents a logarithmic volume. Serial Data (VV) Audio Volume 90 – 99 +10dB 80 0dB 60 -20dB 0 – 28 -52dB AR - Read Mute, Volume For Output/User Port Format:
Resumen del contenido incluido en la página 16
6) Connect All Audio Outputs/Users to an Input/CPU - connect all outputs to an input (Audio ports only) 7) Change Mute Status for Audio Output/User - mute or un-mute the Audio port output 8) Change Volume for Audio Output/User - change Audio port output volume 9) Read Connection for KVM Output/User - read what input is connected to the specified output (KVM ports only) a) Read Connection for Audio Output/User - read what input is connected to the specified output (Audio ports only) b) Read Mute
Resumen del contenido incluido en la página 17
Infrared Control (Optional) Infrared Control (Optional) IRT-20X16 IRT-20X16 Included with IRT-20x16: 1 23 4 5 1. Move ON / OFF I switch to the ON 67 8 9 10 N • (1) Infrared Transmitter P position. 11 12 13 14 15 U 4. Select one of • (2) AA Cell Batteries T S the 20 input 16 17 18 19 20 touch activated Instructions 12 34 ON buttons O U 5 6 78 1. Move ON/OFF switch to the ON position. T OFF P 9 10 11 12 2. Select one of U T the 16 output 13 14 15 16 S Select Output First touch activated LO BA
Resumen del contenido incluido en la página 18
DDC Support (Optional) DDC Support (Optional) DDC information allows the CPU to automatically select the optimal resolution for the monitor by receiving, at power up, information from the monitor concerning its resolution specifications. When DDC Support is installed, the DDC information is acquired from the monitor by the VEEMUX-A switch when the VEEMUX is powered-up. A monitor with DDC support must be connected to MONITOR 1 for this to occur. The DDC information will be made available at eve
Resumen del contenido incluido en la página 19
Rack Mounting Instructions Rack mounting Instructions This NTI switch was designed to be directly mounted to a rack. It includes a mounting flange to make attachment easy. Install 4 captive nuts to the rack in locations that line up with the holes (or slots) in the mounting flange on the NTI switch. Then secure the NTI switch to the rack using four 3/16" diameter screws (not provided). Each screw should be of sufficient length to go completely through the NTI mounting flange, rack frame
