Resumen del contenido incluido en la página 1
400 Series
Industrial Ethernet Switches
Installation
Guide
(Revised 2010-11-15) 1
Resumen del contenido incluido en la página 2
Industrial Ethernet Switch Installation Guide 405TX 405FX-SC 405FX-ST 405FXE-SC-YY 405FXE-ST-YY Where: YY = -15, -40, or -80 (Revised 2010-11-15) 2
Resumen del contenido incluido en la página 3
Copyright, © N-TRON Corp., 2008 820 S. University Blvd., Suite 4E Mobile, AL 36609 USA All rights reserved. Reproduction, adaptation, or translation without prior written permission from N-TRON Corp. is prohibited, except as allowed under copyright laws. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks of their respective owners. The information contained in this docu
Resumen del contenido incluido en la página 4
Safety Warnings ELECTRICAL SAFETY WARNING: Do not disconnect while circuit is live, unless area is known to be non-hazardous. WARNING: Disconnect the power cable before removing the enclosure top. WARNING: Do not operate the unit with the top cover removed. WARNING: Properly ground the unit before connecting anything else to the unit. Units not properly grounded may result in a safety risk and could be hazardous and may void the warranty. See the grounding technique secti
Resumen del contenido incluido en la página 5
405FX, 405FXE, & 405TX Industrial Ethernet Switches The 405TX and 405FX Unmanaged Industrial Ethernet Switches support high speed layer 2 switching between ports. The 405TX is an affordable 5 port unmanaged switch that is capable of auto negotiating 10/100 Mb and half/full duplex communications. The N-TRON 405TX is housed in a ruggedized steel enclosure, and provides 5 Category 5 compliant 10/100-BaseT connections for high performance network design, and hub/repeater upgrades. Th
Resumen del contenido incluido en la página 6
PACKAGE CONTENTS Please make sure the Ethernet Switch package contains the following items: 1. 405FX/405FXE/405TX Ethernet Switch 2. This Installation Guide Contact your carrier if any items are damaged. INSTALLATION Read the following warning before beginning the installation: WARNING The 405FXE unit contains a Class 1 Laser. Do not stare into the laser beam (fiber optic connector) when installing or operating the product. Never install or work on electrical equip
Resumen del contenido incluido en la página 7
405FX/405FXE HALF DUPLEX SETUP While all RJ45 ports are Autosensing, the 405FX/405FXE Fiber Optic Port is factory configured for full duplex operation. In the event half duplex operation is desired, follow these steps: 1. Remove the Voltage Input Power Plugs. 2. Remove the top cover (8 screws). 3. Remove the jumper plug (JP1) from pins 1 and 2. 4. Replace the top cover. 5. Proceed with the installation. Full Duplex = Pins 1 and 2 shorted. Half Duplex = Remove jumper.
Resumen del contenido incluido en la página 8
DIN-Rail Mounting Install the unit in a standard DIN-Rail. Recess the unit to allow at least 5” of horizontal clearance for fiber optic cable bend radius (2” for TX models). Note: This unit may be mounted horizontally or vertically. To install the unit to 35 mm industrial DIN-Rail - Place the top edge of the included mounting bracket on the back of the unit against the top flange of the DIN-Rail at a 15° angle. Rotate the bottom of the unit to the back (away from you) until it snaps
Resumen del contenido incluido en la página 9
FRONT PANEL From Left to Right: LNK Link LED for Fiber Optic Port (405FX/FXE only) TX Fiber Optic Transmit Port (405FX/FXE Only) RX Fiber Optic Receive Port (405FX/FXE Only) ACT Activity LED for Fiber Optic Port (405FX/FXE only) X RJ45 Crossover Uplink Port (405TX Only) RJ45 Ports Auto sensing 10/100BaseT Connections ! Red LED indicates controller error Green LED lights when Power is connected NOTE: Each RJ45 data port has two LED’s located at the top of each con
Resumen del contenido incluido en la página 10
LED’s: The table below describes the operating modes: LED Color Description GREEN Power is Applied OFF Power is OFF RED Controller HW Error ! OFF No Errors. Normal Operation. GREEN Link between ports LNK established OFF No Link between ports GREEN Data is active between ACT ports OFF Data is inactive between ports APPLYING POWER (Side View) Unscrew & Remove the DC Voltage Input Plug(s) from the side header Install the DC Power Cables into the Plug(s) (obs
Resumen del contenido incluido en la página 11
N-TRON SWITCH GROUNDING TECHNIQUES The grounding philosophy of any control system is an integral part of the design. N-Tron switches are designed to be grounded, but the user has been given the flexibility to float the switch when required. The best noise immunity and emissions (i.e. CE) are obtained when the N-Tron switch chassis is connected to earth ground via a drain wire. Some N-Tron switches have metal din-rail brackets that can ground the switch if the din-rail is grounded. In
Resumen del contenido incluido en la página 12
RJ45 CONNECTOR CRIMP SPECIFICATIONS Please reference the illustration below for your Cat5 cable specifications: (Revised 2010-11-15) 12
Resumen del contenido incluido en la página 13
CONNECTING THE UNIT For 405FX & 405FXE units, remove the dust cap from the fiber optic connectors and connect the fiber optic cables. The TX port on the 405FX should be connected to the RX port of the far end station. The RX port on the 405FX should be connected to the TX port of the far end station. For 10/100 Base-TX ports, plug a Category 5 twisted pair cable into the RJ45 connector. Connect the other end to the far end station. Verify that the LNK LED’s are ON once the connectio
Resumen del contenido incluido en la página 14
KEY SPECIFICATIONS Physical Height: 2.13" (5.41 cm) Width: 5.00" (12.70 cm) Depth: 3.00" (7.62 cm) Weight: ~ 1.2 lbs. (0.6 kg) (Note: can be mounted horizontally or vertically) Electrical Input Voltage: 10-30 VDC (Regulated) Input Current: 220mA max. @ 24VDC (Steady State) Inrush Current: 14.0Amp/0.9ms max. @ 24VDC Input Ripple: Less than 100 mV Input Wire Size: 16-28 AWG Environmental Operating Temperature: -20°C to 70°C Storage Temperature: -40°C to
Resumen del contenido incluido en la página 15
Regulatory Approvals: Safety: Suitable for use in Class I, Division 2, Groups A, B, C, and D Hazardous Locations, or Non-hazardous locations only. EMI: EN55022 – Class A FCC Part 15 Class A EMS: EN55024:1998 EN61000-4-2:1995 EN61000-4-3:1997 EN61000-4-4:1995 EN61000-4-5:1995 EN61000-4-6:1996 GOST-R Certified. Warranty: Effective January 1, 2008, all N-TRON products carry a 3 year limited warranty from the date of purchase. (Revised 2010-11-15) 15
Resumen del contenido incluido en la página 16
N-TRON Limited Warranty N-TRON, Corp. warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use and service, for the applicable warranty period from the date of purchase from N-TRON or its authorized reseller. If a product does not operate as warranted during the applicable warranty period, N-TRON shall, at its option and expense, repair the defective product or part, deliver to customer an equivalent product or part to re
