Manual de instrucciones de Moxa Technologies EDS-205

Resumen del contenido incluido en la página 1

Moxa EtherDevice Switch
EDS-205 Hardware Installation Guide










Third Edition, June 2008











© 2008 Moxa Inc., all rights reserved.
Reproduction without permission is prohibited.

P/N: 1802002050000

Resumen del contenido incluido en la página 2

Overview The Moxa EtherDevice™ Switches, EDS-205 series, are entry-level 5- port Ethernet Switches that provide a cost-effective solution for your industrial Ethernet connection. For EDS-205, you could choose either DC power input from 12 to 48 V or AC o power input from 18 to 30V. These products can operation from –10 to 60 C, and the rugged hardware design makes EDS-205 perfect for ensuring that your Ethernet equipment can meet demanding industrial applications. Throughout this Ha

Resumen del contenido incluido en la página 3

Panel Layout of EDS-205 Serieseries Top View 1. Heat dissipation orifices 1 2. Terminal block for power input and grounding 3. Moxa Logo V+ 4. Power input LED 2 24 VDC 24 VAC 5. 10/100BaseT(X) Port 6. TP port’s 100 Mbps LED 7. TP port’s 10 Mbps LED 8. DIN-Rail kit Front View 2 3 P 4 5 4 5 3 2 100 6 1 10 7 Rear View 8

Resumen del contenido incluido en la página 4

Mounting Dimensions DIN-Rail Mounting The plastic DIN-Rail attachment plate should already be fixed to the rear panel of EDS when you take it out of the box. If you need to reattach the DIN-Rail attachment plate to EDS, make sure the DIN-Rail kit is situated towards the top, as shown in the figures below. STEP 1: STEP 2: Insert the top of the DIN-Rail into The DIN-Rail attachment unit will the slot. snap into place as shown below.

Resumen del contenido incluido en la página 5

To remove Moxa EDS-205 from the DIN-Rail, insert a flat-blade screw driver horizontally into the DIN-Rail kit under the EDS-205, and then pull it upwards and release EDS towards you away from the DIN-Rail. Wiring Requirements Safety First! Be sure to disconnect the power cord before installing and/or wiring your Moxa EtherDevice Switch. Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes dictating the maximum current allowab

Resumen del contenido incluido en la página 6

Grounding Moxa EtherDevice Switch Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the right most of 3-contact terminal block to the grounding surface prior to connecting devices. This product is intended to be mounted to a well-grounded mounting surface such as a metal panel. Wiring the Power Inputs The two left-most contacts of the 3-contact terminal block connector on EDS’s top panel are us

Resumen del contenido incluido en la página 7

Communication Connections EDS-205 has five10/100BaseT(X) Ethernet ports. 10/100BaseT(X) Ethernet Port Connection The 10/100BaseT(X) ports located on EDSS’s front panel are used to connect to Ethernet-enabled devices. Below we show pinouts for both MDI (NIC-type) ports and MDI-X (HUB/Switch-type) ports, and also show cable wiring diagrams for straight-through and cross-over Ethernet cables. RJ45 (8-pin, MDI) Port Pinouts RJ45 (8-pin, MDI-X) Port Pinouts RJ45 (8-pin) to RJ45 (8-p

Resumen del contenido incluido en la página 8

LED Indicators The front panel of Moxa EtherDevice Switch contains several LED indicators. The function of each LED is described in the table below. LED Color State Description On Power is being supplied to power input. P AMBER Power is not being supplied to power Off input. On TP port’s 10 Mbps link is active. 10M (TP) GREEN Blinking Data is being transmitted at 10 Mbps. Off TP Port’s 10 Mbps link is inactive On TP port’s 100 Mbps link is active. 100M (TP) GREEN Blinking Data is b

Resumen del contenido incluido en la página 9

Switching and Address Learning Moxa EtherDevice Switch has an address table that can hold up to 1K node addresses, which makes it suitable for use with large networks. The address tables are self-learning, so that as nodes are added or removed, or moved from one segment to another, Moxa EtherDevice Switch automatically keeps up with new node locations. An address-aging algorithm causes the least-used addresses to be deleted in favor of newer, more frequently used addresses. To reset the

Resumen del contenido incluido en la página 10

Regulatory Approvl Safety UL508 EMI FCC Part 15, CISPR (EN55022) class A EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), Shock IEC 60068-2-27 Free Fall IEC 60068-2-32 Vibration IEC 60068-2-6 WARRANTY 5 years Technical Support Contact Information www.moxa.com/support Moxa Americas: Moxa China (Shanghai office): Toll-free: 1-888-669-2872 Toll-free: 800-820-5036 Tel: +1-714-528-6777 Tel: +86-21-5258-9955 Fax: +