Resumen del contenido incluido en la página 1
Foundry FastIron LS
Layer 2 Compact Switch
Hardware Installation Guide
FastIron LS 624
FastIron LS 648
FGS Release 04.0.00
™
4980 Great America Parkway
Santa Clara, CA 95054
Tel 408.207.1700
September 2007
Resumen del contenido incluido en la página 2
Copyright © 2007 Foundry Networks, Inc. All rights reserved. No part of this work may be reproduced in any form or by any means – graphic, electronic or mechanical, including photocopying, recording, taping or storage in an information retrieval system – without prior written permission of the copyright owner. The trademarks, logos and service marks ("Marks") displayed herein are the property of Foundry or other third parties. You are not permitted to use these Marks without the prior writte
Resumen del contenido incluido en la página 3
Contents CHAPTER 1 ABOUT THIS GUIDE..................................................................................... 1-1 INTRODUCTION ...........................................................................................................................................1-1 WHAT’S INCLUDED IN THIS EDITION? ...........................................................................................................1-1 AUDIENCE ..................................................................
Resumen del contenido incluido en la página 4
Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide POWER PRECAUTIONS .........................................................................................................................3-4 PREPARING THE INSTALLATION SITE ............................................................................................................3-5 CABLING INFRASTRUCTURE ..................................................................................................................3-5 I
Resumen del contenido incluido en la página 5
Contents INSTALLING AN OPTIONAL MODULE INTO THE SWITCH ............................................................................5-5 REMOVING A 10-GIGABIT ETHERNET MODULE .......................................................................................5-5 REPLACING A FIBER OPTIC MODULE ...........................................................................................................5-5 REMOVING A FIBER OPTIC MODULE ................................................................
Resumen del contenido incluido en la página 6
Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide APPENDIX B CAUTIONS AND WARNINGS..........................................................................B-1 CAUTIONS ................................................................................................................................................. B-1 WARNINGS ................................................................................................................................................ B-4 v
Resumen del contenido incluido en la página 7
Chapter 1 About This Guide Introduction This guide describes the following product families from Foundry Networks: FastIron LS (FLS) Layer 2 Compact Switch This guide includes procedures for installing the hardware and configuring essential, basic parameters such as permanent passwords and IP addresses. The basic software configuration procedures show how to perform tasks using the CLI. This guide also includes instructions for managing and maintaining the hardware. This guide applies to th
Resumen del contenido incluido en la página 8
Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide CAUTION: A caution calls your attention to a possible hazard that can damage equipment. WARNING: A warning calls your attention to a possible hazard that can cause injury or death. Related Publications The following Foundry Networks documents supplement the information in this guide. Foundry FastIron Configuration Guide - provides basic configuration procedures, including configuration information for enterprise routing p
Resumen del contenido incluido en la página 9
Chapter 2 Product Overview ® This chapter contains an overview of the FastIron LS Layer 2 Compact Switch. This chapter contains the following information: Table 2.1: Chapter Contents Description See Page Product overview and the benefits each product offers 2-1 Network topologies in which the devices will be commonly 2-1 deployed Hardware features and how each major hardware 2-1 component functions Hardware Features The FastIron LS Series includes two models, the FastIron LS 624 with an option f
Resumen del contenido incluido en la página 10
Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide The following figures show the front panels of these FastIron LS models. Figure 2.1 FastIron LS 624 Fastlron LS 624 FLS 624 Figure 2.2 FastIron LS 648 Fastlron LS 648 FLS 648 45 46 47 48 Figure 2.3 FastIron LS 624 and 648 rear panel RPSDCIn12V 13A 100-240V~ 50-60Hz 2A Figure 2.4 FastIron LS 624 with module installed Fastlron LS 624 FLS 624 Figure 2.5 FastIron LS 624 and 648 rear panel with modules Installed RPSDCIn12V 13A 100
Resumen del contenido incluido en la página 11
Product Overview 100/1000 ports with mini-GBIC slots for SFP MSA-compliant fiber transceivers Optional 10-Gigabit uplink modules For information about the type of fiber optic modules supported on the FastIron LS, see “Fiber Optic Modules” on page 2-7. FastIron LS 10/100/1000BASE-T Ports The switches contain 24/48 RJ-45 ports that operate at 10 Mbps or 100 Mbps, half or full duplex, or at 1000 Mbps, full duplex. Because all ports on these switches support automatic MDI/MDI-X operation, you
Resumen del contenido incluido en la página 12
Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide 10 Gigabit Ethernet Module Slots These switches include two slots on the rear panel for single-port 10GBASE uplink modules with XFP transceivers, and a single port CX4 module. The 10GBASE transceivers operate at 10 Gbps full duplex with support for asymmetric flow control (that is, the port honors incoming pause frames, but does not originate pause frames). 10 Gbps CX4 Ports This section describes the 10-GbE CX4 module. 10
Resumen del contenido incluido en la página 13
Product Overview Figure 2.7 CX4 Transceiver Cable CX4 Transceiver Infiniband cable Port, System and Module Status LEDs These switches include a display panel for key system and port indications that simplify installation and network troubleshooting. The LEDs, which are located on the front panel for easy viewing, are shown below and described in the following tables. Figure 2.8 Port LEDs Port Status LEDs Table 2.3: Port Status LEDs LED Condition Status Link/ On/Flashing Amber Port has a valid
Resumen del contenido incluido en la página 14
Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide Figure 2.9 System LEDs System Status LEDs Fastlron LS 624 FLS 624 Table 2.4: Status LEDs LED Condition Status Power Green Internal power is operating normally. Amber Internal power supply failure. Off Power off or failure. Diag Green System self-diagnostic test successfully completed. Amber System self-diagnostic test has detected a fault. RPS Green Redundant power supply is providing power. Amber Primary power supply is acti
Resumen del contenido incluido en la página 15
Product Overview 1. Not currently in use. Figure 2.10 Module LED Link/Activity LED Table 2.5: Port Status LEDs LED Condition Status Link/Activity On Port has a valid link at 10 Gbps. On/Flashing Green Flashing indicates activity. Off The link is down. Fiber Optic Modules A list of the types of fiber optic modules supported on Layer 2 Compact Switches can be found in “Cable length summary table” on page 2-7 NOTE: Some older SFP modules (mini-GBICs for Gigabit Ethernet ports) have latching mecha
Resumen del contenido incluido en la página 16
Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide 2 - 8 © 2007 Foundry Networks, Inc. September 2007
Resumen del contenido incluido en la página 17
Chapter 3 Installing a FastIron LS Switch WARNING: The procedures in this manual are intended for qualified service personnel. This chapter describes how to physically install the FastIron LS. This chapter contains the following topics: Table 3.1: Chapter Contents Description See Page Unpacking the hardware 3-1 Summary of installation tasks 3-3 Installation precautions 3-4 Site preparation 3-5 Installing a redundant power supply 3-8 Mounting the device 3-5 Installing an Optional Module 3-14 Pow
Resumen del contenido incluido en la página 18
Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide Package Contents Foundry Networks FastIron LS 115V AC power cable (for AC sourced devices) Rack mount brackets CD-ROM containing software images and the user documentation (including this guide) Warranty card General Requirements To manage the system, you need the following items for serial connection to the switch or router: A management station, such as a PC running a terminal emulation application. A stra
Resumen del contenido incluido en la página 19
Installing a FastIron LS Switch Summary of Installation Tasks Follow the steps listed below to install your FastIron LS. Details for each of these steps are provided in this chapter and in the following chapter. Table 3.2: Summary of Installation Tasks Task Task Where to Find More Information Number 1 Ensure that the physical environment that will host the “Preparing the Installation Site” on page 3-5 device has the proper cabling and ventilation. 2 Install any required optional modules into
Resumen del contenido incluido en la página 20
Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide Installation Precautions Follow these precautions when installing a Foundry device. General Precautions WARNING: All fiber-optic interfaces use Class 1 lasers. CAUTION: Do not install the device in an environment where the operating ambient temperature might exceed o o 50 C (121 F). CAUTION: Make sure the air flow around the front, sides, and back of the device is not restricted. CAUTION: Never leave tools inside the device
