Resumen del contenido incluido en la página 1
Citrix NetScaler 10 Quick Start Guide:
SDX
11500/13500/14500/16500/18500/20500
Platform
Citrix NetScaler 10
Resumen del contenido incluido en la página 2
Copyright and Trademark Notice © Copyright 2013 Citrix Systems, Inc. All rights reserved. NO PART OF THIS DOCUMENT MAY BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY MEANS OR USED TO MAKE DERIVATIVE WORK (SUCH AS TRANSLATION, TRANSFORMATION, OR ADAPTATION) WITHOUT THE EXPRESS WRITTEN PERMISSION OF CITRIX SYSTEMS, INC. ALTHOUGH THE MATERIAL PRESENTED IN THIS DOCUMENT IS BELIEVED TO BE ACCURATE, IT IS PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE ALL RESPONSIBILI
Resumen del contenido incluido en la página 3
Quick Installation and Configuration Welcome to the Citrix NetScaler Application Delivery product line. Please review the following information before proceeding with installation of the SDX appliance. Before you Begin Verify that the following components and accessories are included: w One NetScaler SDX appliance w One accessory kit that contains: • One RJ-45 to DB-9 adapter • One 6 ft RJ-45/DB-9 cable • Two power cables Note: Make sure that a power outlet is available for each cable. w One sta
Resumen del contenido incluido en la página 4
Quick Installation and Configuration Figure 1-1. Citrix NetScaler SDX 11500/13500/14500/16500/18500/20500 appliance, front panel The following figure shows the back panel of the SDX 11500/13500/14500/16500/18500/20500 appliance. Figure 1-2. Citrix NetScaler SDX 11500/13500/14500/16500/18500/20500 appliance, back panel Configuration Requirements Determine the following information for performing the initial configuration. w NetScaler SDX IP address and subnet mask: The management IP address and t
Resumen del contenido incluido en la página 5
Citrix NetScaler 10 Quick Start Guide: SDX 11500/13500/14500/16500/18500/20500 Platform w Root password: The root user (nsroot) has full administrative privileges on the appliance. The root password is used to authenticate the root user. The default root password is nsroot. You can change this password during initial configuration of the appliance. Installation Installation involves rack-mounting the appliance, installing transceivers (if available), and connecting the appliance to the network a
Resumen del contenido incluido en la página 6
Quick Installation and Configuration w Allow the power supply units and hard drives to cool before touching them. Install the equipment near an electrical outlet for easy access. w w Mount equipment in a rack with sufficient airflow for safe operation. w For a closed or multiple-unit rack assembly, the ambient operating temperature of the rack environment might be greater than the ambient temperature of the room. Therefore, consider the lowest and highest operating temperatures of the equipment
Resumen del contenido incluido en la página 7
Citrix NetScaler 10 Quick Start Guide: SDX 11500/13500/14500/16500/18500/20500 Platform Connecting a NetScaler SDX Appliance to the Network Connect the interfaces on the appliance to the network ports on the appropriate switches by using Ethernet/fiber optic cables. Figure 1-4. Connecting a Citrix NetScaler SDX appliance to the network Warning: Connecting multiple network ports to the same switch or VLAN can result in a network loop. Note: By default, the NetScaler SDX appliance is configured to
Resumen del contenido incluido en la página 8
Quick Installation and Configuration Note: Electrical Safety Precautions Caution: During installation or maintenance procedures, wear a grounding wrist strap to avoid ESD damage to the electronics of the appliance. Use a conductive wrist strap attached to a good earth ground or to the appliance. You can attach it to the connector beside the ESD symbol on the back. Basic electrical safety precautions should be followed to protect yourself from harm and the appliance from damage. w Be aware of the
Resumen del contenido incluido en la página 9
Citrix NetScaler 10 Quick Start Guide: SDX 11500/13500/14500/16500/18500/20500 Platform Initial Configuration through the Management Service User Interface To set up the appliance by using the Management Service user interface, connect a workstation or laptop to the same network as the appliance. To configure the NetScaler SDX appliance by using the Management Service user interface 1. Connect the NetScaler SDX appliance to a management workstation or network by using interface 0/1. 2. Open a br
Resumen del contenido incluido en la página 10
Quick Installation and Configuration Note: After changing the network configuration, close all browser instances and open a new browser instance to access the appliance. Initial Configuration through the Serial Console To perform initial configuration of the SDX appliance from outside the L2 domain, connect to the console port of the appliance and follow the instructions carefully. Note: networkconfig utility is available from build 72.5 and later. To configure the NetScaler SDX appliance by usi
Resumen del contenido incluido en la página 11
Citrix NetScaler 10 Quick Start Guide: SDX 11500/13500/14500/16500/18500/20500 Platform Changing the Password of the Default User Account The default user account provides complete access to all features of the Citrix NetScaler SDX appliance. Therefore, to preserve security, the nsroot account should be used only when necessary, and only individuals whose duties require full access should know the password for the nsroot account. Citrix recommends changing the nsroot password frequently. If you
Resumen del contenido incluido en la página 12
Quick Installation and Configuration 4. In the Password box, type nsroot. 5. In the Configuration tab, click Network and type values for the following parameters: • IP Address—IP address of the LOM port. • Subnet Mask—Subnet mask used to define the subnet of the LOM port. • Default Gateway—IP address of the router that connects the LOM port to the network. 6. Click Save. Power Cycling the Appliance You can remotely turn off the appliance and turn it back on. The result is similar to pressing the
Resumen del contenido incluido en la página 13
Citrix NetScaler 10 Quick Start Guide: SDX 11500/13500/14500/16500/18500/20500 Platform Specifications SDX 11500/13500/14500/16500/18500/205 00 Number of power supplies 2 AC power supply input voltage, 100-240 VAC frequency, and current 50-60 Hz 6.5-3.5 A Maximum power consumption 650 W Heat dissipation 2200 BTU per hour Weight 46 lbs Height 2U Width EIA 310-D for 19-inch racks Depth 28 in or 71.68 cm Operating temperature (degree Celsius) 0-40 Humidity range (non-condensing) 5%-95% Safety certi
Resumen del contenido incluido en la página 14
Quick Installation and Configuration 2. Click the Documentation tab. 3. To view a short description of each document, hover your cursor over the title. To open a document, click the title. To contact Citrix Support, call 1-800-4-CITRIX (1-800-424-8749), or log on to MyCitrix at http://www.citrix.com. You will be asked for your hardware serial number as part of the support process. Detailed instructions for contacting support can be found at: http://citrix.com/site/ resources/dynamic/sup2nd/Citr
