Resumen del contenido incluido en la página 1
PowerPlus Amplifiers
420, 840, 900, 1150, 1302, 1304
Installation & Operation Manual
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Features and Specifications . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Speaker Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Indicators and Controls . . . . . . . . . . . . . . .
Resumen del contenido incluido en la página 2
PowerPlus Amplifiers Introduction The Jensen PowerPlus series of amplifiers were designed to meet or exceed the CEA-2006 test standards. These new standards give all participating manufacturers (and many don't participate) a baseline when comparing amplifiers of similar power output. The CEA Power rating protects you, the customer. “Power is power – it doesn't matter who makes it,” is not always true. What does matter is whether the power can be produced in the first place. The RMS rating
Resumen del contenido incluido en la página 3
PowerPlus Amplifiers • Signal to Noise @ 1 kHz: >100dB (rated power) Features and Specifications • Channel Separation @ 1 kHz: >60dB Your new PowerPlus Jensen mobile stereo power amplifier is the amplifier of • Frequency Response: 5-60 kHz, -3dB choice for the high demands of auto sound reproduction. With its deep-bass • Input Impedance: 20 kHz, nominal reproduction and plenty of reserve power, low harmonic distortion and neutral • THD+N @ 5 watts: 0.02%, 1 kHz, 14.4VDC r
Resumen del contenido incluido en la página 4
PowerPlus Amplifiers Installation Before you begin the installation of your PowerPlus series amp remember, going to the vehicle chassis) and make sure the battery is grounded to the there are two ways to do things – right and twice! Use the proper installation chassis with at least a #8 gauge wire. Also check the alternator connections, techniques, tools and accessories to ensure that your Jensen PowerPlus making sure they are tight and free from corrosion, rust or dirt. series amp will put o
Resumen del contenido incluido en la página 5
40 WATTSx4 CD2620 CD RECEIVER 6 LOC/DX 1 2 3 4 5 VOL INT CD-R/RW SUB-W SUB-W MONO MONO O E AUX IN M MODE D iEQ 4 AUX AUX JPTH DISP DISP CHANGER -BASS AS/PS AS/PS RPT iX SCAN iEQ BAND MUTE SHF DN UP E AD PowerPlus Amplifiers Power Wiring Charging System Power Terminal (+12V/B+) In some cases, the installation of just one (1) amplifier could be enough to Connect the main power wire to the battery, within 18 inches from the positive overload your factory electrical system (i.e.
Resumen del contenido incluido en la página 6
PowerPlus Amplifiers Ground Terminal (GND) Make the ground lead as short as possible, leaving enough length to complete the installation and to allow for any service that may be needed at a later date. To ensure a good ground, scrape away any paint or undercoating to expose bare metal. Use a "ring" terminal of the proper gauge and an "outside star washer" (between the chassis and ring terminal) when making your ground connection. Although you’ve scraped away the paint to expose bare metal,
Resumen del contenido incluido en la página 7
PowerPlus Amplifiers PowerPlus 420/1302 Speaker Wiring Two Speakers One Subwoofer The Speaker Wiring diagrams illustrate options for connecting one or two speakers. Observe the proper speaker polarity. NOTE: PowerPlus amplifiers can drive speakers with a nominal impedance range of 2~ 4-ohms. For maximum power, configure your speakers for a nominal 2-ohm load. NOTE: Do not overlook the use of the proper gauge speaker wire. The PowerPlus se
Resumen del contenido incluido en la página 8
PowerPlus Amplifiers PowerPlus 840/1304 Two Speakers and Bridged Subwoofer Four Speakers HPF LPF OFF HPF LPF OFF HPF LPF OFF HPF LPF OFF SPEAKER OUTPUT CH1 CH2 CH3 CH4 SPEAKER OUTPUT ++ – – + – + – CH1 CH2 CH3 CH4 ++ – – + – + – + BRIDGED – + BRIDGED – + BRIDGED – + BRIDGED – 4 ohm nominal 2 ohm minimum 4 ohm nominal 4 ohm nominal 4 ohm nominal 2 ohm minimum 2 ohm minimum Two Subwoofers HPF LPF OFF HPF LPF OFF SPEAKER OUTPUT CH1 CH2 CH3 CH4 ++ – – + – + – + BRID
Resumen del contenido incluido en la página 9
PowerPlus Amplifiers Input Wiring Most trunk/hatchback installations will require a 15-20 foot RCA cable, while PowerPlus 840/1304 pickup trucks and under-seat mounting will require a 6-12 foot RCA cable. The PowerPlus 1304 and 840 can be configured for three different input Connect an RCA cable from your receiver to the RCA input on your amplifier. modes: 2 channel, 3 channel or 4 channel. PowerPlus 420/900/1150/1302 Input Wiring - Stereo Mode 2 Channel RCA Cable MODE CAR
Resumen del contenido incluido en la página 10
PowerPlus Amplifiers 4 Channel MODE 432 MODE CH3 CH1 432 CH4 CH2 HPF LPF OFF 40Hz 240Hz 40Hz 400Hz 0dB 12dB 5V 0.4V 5V 0.4V 0dB 12dB 40Hz 400Hz 40Hz 240Hz HPF LPF OFF X-OVER LPF HPF BASS EQ GAIN 3/4 INPUT OUTPUT 1/2 INPUT GAIN BASS EQ HPF LPF X-OVER NOTE: The use of good quality RCA cables is just as important as power and speaker wire. Choose a high quality low capacitance cable for the best results. Connecting Additional Amplifiers Pass-Thru RCA connectors are provided to connect additional
Resumen del contenido incluido en la página 11
PowerPlus Amplifiers Indicators and Controls speakers (6 1/2", 6 X 9", etc.) by adjusting the crossover to a higher setting Power Indicator (POWER) (80–100Hz). The power indicator provides a visual indication that the amplifier is turned on. Crossover (X-OVER) Input Level Control (LEVEL/GAIN) The Jensen PowerPlus series of amplifiers have built-in low-pass and high- The INPUT LEVEL control (or GAIN) matches the output of your radio to the pass crossover filters for bi-ampli
Resumen del contenido incluido en la página 12
PowerPlus Amplifiers Testing Remote Input Level Control Before finishing the installation, perform the following tests to make sure the The PowerPlus 900, 1150 and 1302 come equipped with a Remote Input wiring is correct and everything is operating properly. Level Control. The Remote Input Level Control allows the input level to be adjusted from an alternate location. It can be mounted under-dash or in-dash. Reconnect Battery When the amplifier is used to drive subwoofers and the low pass cro
Resumen del contenido incluido en la página 13
PowerPlus Amplifiers Short circuit Blown speakers Check all speakers Troubleshooting protection activated Speaker wire(s) shorting Check for faulty wiring Problem Possible Cause Corrective Action to ground Amplifier does not No power to +12V Check fuse(s) Defective crossover Faulty passive crossover turn on terminal Low impedance Amp connected to Check speaker connections No power to REM Check head unit fuse(s) and protection activated improper load terminal wiring Amp will
Resumen del contenido incluido en la página 14
PowerPlus Amplifiers CEA Power Output PowerPlus 1302 Power Output: 175 watts RMS X 2 channels into 4-ohms @ < 1% THD+N Signal to Noise Ratio: 100dBA below reference (Reference: 1 watt, 4-ohms) Additional Power Output: 280 watts RMS X 2 channels into 2-ohms @ < 1% THD+N 570 watts RMS X 1 channels (Bridged Mono) into 4-ohms @ < 1% THD+N Frequency Response: 10Hz to 60 kHz, -3dB (Reference: 1 watt) Dimensions: L15.5" x 2.5" x 11.75" PowerPlus 1304 Power Output: 117 watts RMS X 4 channels into 4-ohm
