Manual de instrucciones de Allied Telesis SB251-08

Manual de instrucciones del aparato Allied Telesis SB251-08

Aparato: Allied Telesis SB251-08
Categoría: Interruptor
Fabricante: Allied Telesis
Tamaño: 0.1 MB
Fecha de añadido: 3/12/2013
Número de páginas: 12
Imprimir el manual

Descargar

¿Cómo se utiliza?

Nuestro propósito es proporcionarte el acceso más rápido posible a los contenidos incluidos en los manuales de instrucciones del aparato Allied Telesis SB251-08. Utilizando la vista previa online, puedes ver rápidamente el índice de contenidos y pasar a la página donde encontrarás la solución a tu problema con Allied Telesis SB251-08.

Para tu comodidad

Si ver los manuales de instrucción de Allied Telesis SB251-08 directamente en esta página no es cómodo para ti, puedes utilizar dos soluciones posibles:

  • Vista en pantalla completa – Para ver cómodamente los manuales de instrucciones (sin descargarlos en tu ordenador) puedes utilizar el modo de vista en pantalla completa. Para activar la vista del manual Allied Telesis SB251-08 en pantalla completa, utiliza el botón Pantalla completa
  • Descargar al ordenador – también puedes descargar el manual de instrucciones de Allied Telesis SB251-08 a tu ordenador y guardarlo en tu colección. Sin embargo, si no quieres ocupar espacio en tu dispositivo, siempre podrás descargarlo de ManualsBase.
Allied Telesis SB251-08 Manual de instrucciones - Online PDF
Advertisement
« Page 1 of 12 »
Advertisement
Versión impresa

Muchas personas prefieren no leer el documento en la pantalla, sino en versión impresa. La opción de impresión también está prevista y puedes utilizarla haciendo clic en el enlace más arriba - Imprimir el manual. No tienes que imprimir el manual completo de Allied Telesis SB251-08, solo las páginas que elijas. Ahorra papel.

Resúmenes

A continuación encontrarás resúmenes de los contenidos incluidos en las páginas posteriores del manual de instrucciones para Allied Telesis SB251-08. Puedes utilizarlos si quieres ver rápidamente el contenido que se encuentra en la siguientes páginas del manual.

Resúmenes de contenidos
Resumen del contenido incluido en la página 1

Patch Release Note
Patch SB251-08
For SwitchBlade 4000 Series Switches and
AT-9800 Series Switches
Introduction
This patch release note lists the issues addressed and enhancements made in
patch SB251-08 for Software Release 2.5.1 on existing models of SwitchBlade
4000 Series Switches and AT-9800 Series Switches. Patch file details are listed in
Table 1.
Table 1: Patch file details for Patch SB251-08.
Base Software Release File sb-251.rez
Patch Release Date 14-May-2003
Compressed Patch File

Resumen del contenido incluido en la página 2

2 Patch Release Note Some of the issues addressed in this Release Note include a level number. This number reflects the importance of the issue that has been resolved. For details on level numbers, please contact your authorised distributor or reseller. Features in SB251-08 Patch SB251-08 includes all issues resolved and enhancements released in previous patches for Software Release 2.5.1, and the following enhancements: PCR: 03251 Module: SWI Level: 2 A fa

Resumen del contenido incluido en la página 3

Patch SB251-08 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 3 Features in SB251-07 Patch file details are listed in Table 2: Table 2: Patch file details for Patch SB251-07. sb-251.rez Base Software Release File 22-Apr-2003 Patch Release Date sb251-07.paz Compressed Patch File Name 86524 bytes Compressed Patch File Size Patch SB251-07 includes all issues resolved and enhancements released in previous patches for Software Release 2.5.1, and the following enhancements: PCR: 033

Resumen del contenido incluido en la página 4

4 Patch Release Note  The PORT parameter of the SET STP PORT command specifies either all the ports in a trunk group, or none of the ports in a trunk group.  The STPFORWARD parameter has been added to the ENABLE SWITCH and DISABLE SWITCH commands. If STPFORWARD is enabled, and there is no enabled STP instance, then the switch will forward all received BPDUs. If STPFORWARD is enabled, and an STP instance is enabled, then STPFORWARD will be disabled by default and a message will be gene

Resumen del contenido incluido en la página 5

Patch SB251-08 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 5 Patch SB251-05 includes all issues resolved and enhancements released in previous patches for Software Release 2.5.1, and the following enhancements: PCR: 03281 Module: SWI Level: 2 Specifying the PORT and SPEED parameters with the CREATE SWITCH TRUNK command did not set ports in a trunk group to advertise the correct trunk group speed and duplex mode. This issue has been resol

Resumen del contenido incluido en la página 6

6 Patch Release Note PCR: 03243 Module: SWI Level: 2 After autonegotiation had finished between two ports, the port on the SwitchBlade would not show link up status when the SHOW SWITCH PORT command was executed. The autonegotiation process is now restarted if autonegotiation is completed and the link is shown as down. PCR: 03249 Module: SWI Level: 4 The LEDs on line cards now continue to flash when activity exists. Previo

Resumen del contenido incluido en la página 7

Patch SB251-08 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 7 PCR: 03060 Module: CORE, SWI Level: 3 Support has been added, to the MIB-2 interface MIB, for the port interface. This means that port counters can now be shown. PCR: 03066 Module: SWI Level: 2 If a hardware filter was added to the switch, with a source VLAN and a destination port of 1, then a host connected to the switch could not PING a host on

Resumen del contenido incluido en la página 8

8 Patch Release Note PCR: 03142 Module: SWI Level: 1 If a BIST was run at low temperatures, for example 5 or 10 degress celcius, on a G8 card, then a watchdog timer restart could occur. The switch now checks for the real course of the external interrupts that occur when running BIST. PCR: 03148 Module: IPG Level: 3 If the Gratuitous ARP feature was enabled on an IP interface, and an ARP packet arrived, (either ARP request, or

Resumen del contenido incluido en la página 9

Patch SB251-08 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 9 PCR: 03023 Module: SWI Network affecting: No The SET SWITCH PORT ACCEPTABLE command did not work correctly on all specified port numbers. This issue has been resolved. PCR: 03028 Module: SWI Network affecting: No A warning message was generated when a slave line card was not initialised, and the configuration script was not loaded. This issue has been resolved. PCR: 03030 Module: SWI Network affecting: No RIP wa

Resumen del contenido incluido en la página 10

10 Patch Release Note Features in SB251-01 Patch file details are listed in Table 8: Table 8: Patch file details for Patch SB251-01. sb-251.rez Base Software Release File 15-Jan-2003 Patch Release Date sb251-01.paz Compressed Patch File Name 71828 bytes Compressed Patch File Size PCR: 02555 Module: SWI Network affecting: No Layer 2 filtering is now working correctly. PCR: 02561 Module: SWI Network affecting: No 32 bit counters now only show 8 bit contents. PCR: 02563 Module: SWI Network affectin

Resumen del contenido incluido en la página 11

Patch SB251-08 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 11 PCR: 02587 Module: OSPF Network affecting: No When OSPF was enabled on startup, an OSPF interface would sometimes stay in the DOWN state. This issue has been resolved. PCR: 03001 Module: SWI CLASSIFIER Network affecting: No The following parameters have been changed CREATE CLASSIFIER, SET CLASSIFIER and SHOW CLASSIFIER commands:  The MACTYPE parameter has been changed to MACTYPE={L2UCAST|L2MCAST|L2BCAST|ANY}.

Resumen del contenido incluido en la página 12

12 Patch Release Note Patch SB251-08 for Software Release 2.5.1 C613-10361-00 REV H


Manuales de instrucciones similares
# Manual de instrucciones Categoría Descargar
1 Allied Telesis 24i Manual de instrucciones Interruptor 24
2 Allied Telesis AT -8000S/24 Manual de instrucciones Interruptor 182
3 Allied Telesis 8100S Manual de instrucciones Interruptor 28
4 Allied Telesis 4000 Series Manual de instrucciones Interruptor 9
5 Allied Telesis 48W Manual de instrucciones Interruptor 5
6 Allied Telesis AT -8000S/48 Manual de instrucciones Interruptor 33
7 Allied Telesis 86241-06 Manual de instrucciones Interruptor 0
8 Allied Telesis 613-001480 Manual de instrucciones Interruptor 4
9 Allied Telesis 8PS Manual de instrucciones Interruptor 1
10 Allied Telesis AT-8100L/8POE Manual de instrucciones Interruptor 3
11 Allied Telesis AT-8100S/24F-LC Manual de instrucciones Interruptor 0
12 Allied Telesis AT-8000GS/48 Manual de instrucciones Interruptor 34
13 Allied Telesis AT-8100S/16F8-SC Manual de instrucciones Interruptor 3
14 Allied Telesis AT-8100S/16F8-LC Manual de instrucciones Interruptor 0
15 Allied Telesis AT-8100S/48 Manual de instrucciones Interruptor 6
16 Sony 4-296-436-11 (2) Manual de instrucciones Interruptor 0
17 3Com 10/100BASE-TX Manual de instrucciones Interruptor 61
18 3Com 2226-SFP Manual de instrucciones Interruptor 688
19 3Com 16985ua.bk Manual de instrucciones Interruptor 10
20 3Com 10BASE-T Manual de instrucciones Interruptor 4