Resumen del contenido incluido en la página 1
Resumen del contenido incluido en la página 2
CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Practice Safe Sound™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Resumen del contenido incluido en la página 3
INTRODUCTION Thank you for your purchase of Orion's 8004 amplifier. Each Orion amplifier is designed to be the leader in its class offering the most power, advanced features, and ease of use. Orion amplifiers are designed as the best affordable high end car audio amplifier money can buy. Listed below are the features of the new Orion 8004. ● 8004 - 100 Watts per channel, four-channel amplifier with dual built-in fully vari- able high-pass, low-pass, and band-pass 12dB/octave crossovers with INTE
Resumen del contenido incluido en la página 4
WARRANTY Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be defective in workmanship or material under normal use, for a period of two years from the date of purchase by the dealer as indicated by the date code marking of the product PROVIDED the product was installed by an authorized Directed dealer. During this two year period, there will be no charge for this replacement PROVIDED the unit is returned to Directed, shipping pre-paid. If
Resumen del contenido incluido en la página 5
SPECIFICATIONS Amplifier Section Power Output 4W Stereo (Watts)1 100 x 4 Power Output 2W Stereo (Watts)2 200 x 4 Power Output 4W Mono (Watts)1 400 x 2 Distortion - with all channels driven < 0.1% THD+N at rated power (20Hz to 20kHz) Frequency Response 20Hz to 20kHz ±0.25dB Linear Bandwidth 10Hz to 50kHz ±3dB Signal-to-Noise Ratio at Rated Power > 100dB Damping Factor > 200 Slew Rate > 20V per usec RCA Input Sensitivity 200mV to 5V Input Impedance 40kW Fuse Type (1) 80 Amp MAXI Dimensions 23.9" x
Resumen del contenido incluido en la página 6
END PANEL LAYOUT 1. Power LED - when lit indicates that the amplifier is on. 2. Front Low-Pass Crossover Switch - activates 2nd order low-pass crossover. 3. Front Low-Pass Frequency Control - adjusts the frequency of the low-pass crossover. 4. Front Gain Control - continuously adjusts from 200mV to 5V for full power output. 5. Front High-Pass Crossover Switch - activates 2nd order high-pass crossover. 6. Front High-Pass Frequency Control - adjusts the frequency of the high-pass crossover. 7. Fro
Resumen del contenido incluido en la página 7
AMPLIFIER SETTINGS Signal Input and Output Configurations The input section of the amplifier consists of a phase switch that sets the output configura- tion, gain controls, and RCA inputs. The input section makes it easy to adapt this amplifier to most system configurations. Four-Channel Amplifier Input Configuration The 4CH / 2CH switch routes input from the front inputs to the rear section of the amplifi- er. This allows the Orion 8004 channel amplifier to utilize a single set of RCA's to feed
Resumen del contenido incluido en la página 8
Fine Tuning the Crossover Frequency The crossover section is marked at four frequency points for ease of system adjustment. These points are 20Hz, 250Hz, 1kHz, and 3kHz. Specific crossover points can be chosen based on the recommended operational bandwidth of your speakers. Auxiliary Output Configurations The auxiliary outputs on Orion amplifiers offer easy, unlimited system expansion. Routing signal from a source unit, pre-amplifier, or equalizer is a matter of connecting RCA's to the RCA Inpu
Resumen del contenido incluido en la página 9
Speaker Connections Four Channel Stereo Configuration ● Front and rear channel lowest recommended impedance is 2W stereo ● Crossover mode, output, and gain configurations are independently adjustable between the front and rear channels. ● Two-channel or four-channel input can be used for this configuration. For source unit fading, use the four-channel input mode. ● Front and rear outputs can be configured for high-pass, low-pass, or full range operation. Two Channel Bridged Configuration ● Front
Resumen del contenido incluido en la página 10
Three Channel Stereo/Bridged Configuration ● Front channels are configured for two-channel stereo operation. ● Front channel lowest recommended impedance is 2W stereo. ● Rear channels are configured for a single channel bridged output. ● Rear channel lowest recommended impedance is 4W. ● Crossover mode, output and gain configurations are independently adjustable between the front and rear channels. ● Two-channel or four-channel input can be used for this configuration. For source unit fading, us
Resumen del contenido incluido en la página 11
AMPLIFIER INSTALLATION Choosing Mounting Locations The location of your amplifier will depend on several important issues. Due to the low pro- file size of the Orion amplifiers, there are many possible installation locations that will yield satisfactory amplifier performance. Always mount the amplifier in a place that protects the amplifier from the elements. In addition, mount the amplifier on a stable, flat surface. NOTE: Mounting amplifiers upside down is not recommended and may cause premat
Resumen del contenido incluido en la página 12
Power for systems with a single amplifier can be supplied by most automotive electrical sys- tems. Systems with multiple amplifiers may require a higher capacity battery, alternator or the use of a storage capacitor. We strongly recommend the use of a Directed Audio Essentials power capacitor with an extra battery in larger stereo systems. Orion amplifiers generate a certain amount of heat as part of normal operation. Be sure the area around the amplifier is unobstructed to allow adequate air ci
Resumen del contenido incluido en la página 13
amplifier is twisted or bent. Step 6 Turn the vehicle's key switch to the off position. Step 7 Disconnect the vehicle's battery ground terminal. Step 8 Connect power wires to the amplifier (ground first, then 12 V(+) and RGC). Step 9 Connect the RCA and speaker wires to the amplifier. Check the quality of your speakers and signal connections. This will determine the ultimate per- formance of your Orion amplifier. Refer to the Signal Input and Output Level Controls and Speaker Connections section
Resumen del contenido incluido en la página 14
Adjusting the Sound of the System Once you have checked the system's operation, adjust the sound of the system. Adjusting the sound of the system is accomplished by setting the level controls and adjusting the internal crossovers. Step 1 Turn the signal source volume control all the way down. Set any tone con- trols to their flat or defeated positions. This includes the loudness control. Step 2 Turn the level controls of the amplifier to their minimum positions. Step 3 Choose music with high dyn
Resumen del contenido incluido en la página 15
Troubleshooting Tips Symptom Probable Cause Action To Take No output Low or no remote turn-on Check remote turn-on voltage at voltage amplifier and repair as needed. Fuse blown Check power wire's integrity and check for speaker shorts. Fix as needed and replace fuse. Power wires not connected Check power wire and ground connections and repair or replace as needed. Audio input not connected Check RCA connections and repair or replace as needed. Speaker wires not Check speaker wires and re
Resumen del contenido incluido en la página 16
Symptom Probable Cause Action To Take Distorted output Internal crossover not set Readjust crossovers. Refer to the properly for speakers Internal Crossover Configuration section of this guide for detailed instructions. Speakers are blown Check system with known work ing speakers and fix or replace as needed. Poor bass response Speakers wired with wrong Check speaker polarity and fix polarity causing cancellation as needed. at low frequencies Crossover set incorrectly Reset crossovers. Refer
Resumen del contenido incluido en la página 17
NOTES ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ _________________
Resumen del contenido incluido en la página 18
Warranty LIMITED TWO YEAR CONSUMER WARRANTY: Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be defective in workmanship or material under normal use, for a period of two years from the date of purchase by the dealer as indicated by the date code marking of the product PROVIDED the product was installed by an authorized Directed dealer. During this two year period, there will be no charge for this replacement PROVIDED the unit is returned
