Manual de instrucciones de Goldstar LWJ0611PCG

Manual de instrucciones del aparato Goldstar LWJ0611PCG

Aparato: Goldstar LWJ0611PCG
Categoría: Aparato de aire acondicionado
Fabricante: Goldstar
Tamaño: 1.43 MB
Fecha de añadido: 7/1/2013
Número de páginas: 32
Imprimir el manual

Descargar

¿Cómo se utiliza?

Nuestro propósito es proporcionarte el acceso más rápido posible a los contenidos incluidos en los manuales de instrucciones del aparato Goldstar LWJ0611PCG. Utilizando la vista previa online, puedes ver rápidamente el índice de contenidos y pasar a la página donde encontrarás la solución a tu problema con Goldstar LWJ0611PCG.

Para tu comodidad

Si ver los manuales de instrucción de Goldstar LWJ0611PCG directamente en esta página no es cómodo para ti, puedes utilizar dos soluciones posibles:

  • Vista en pantalla completa – Para ver cómodamente los manuales de instrucciones (sin descargarlos en tu ordenador) puedes utilizar el modo de vista en pantalla completa. Para activar la vista del manual Goldstar LWJ0611PCG en pantalla completa, utiliza el botón Pantalla completa
  • Descargar al ordenador – también puedes descargar el manual de instrucciones de Goldstar LWJ0611PCG a tu ordenador y guardarlo en tu colección. Sin embargo, si no quieres ocupar espacio en tu dispositivo, siempre podrás descargarlo de ManualsBase.
Goldstar LWJ0611PCG Manual de instrucciones - Online PDF
Advertisement
« Page 1 of 32 »
Advertisement
Versión impresa

Muchas personas prefieren no leer el documento en la pantalla, sino en versión impresa. La opción de impresión también está prevista y puedes utilizarla haciendo clic en el enlace más arriba - Imprimir el manual. No tienes que imprimir el manual completo de Goldstar LWJ0611PCG, solo las páginas que elijas. Ahorra papel.

Resúmenes

A continuación encontrarás resúmenes de los contenidos incluidos en las páginas posteriores del manual de instrucciones para Goldstar LWJ0611PCG. Puedes utilizarlos si quieres ver rápidamente el contenido que se encuentra en la siguientes páginas del manual.

Resúmenes de contenidos
Resumen del contenido incluido en la página 1

Dry Fan
Cool
website: http://www.lgservice.com
e-mail: http://www.lgeservice.com/techsup.html
ROOM AIR CONDITIONER
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
MODEL : M5403R, M5203R, M5203L, M6003R, WM-6011,
LWJ0611PCG, LWC061JGMK1

Resumen del contenido incluido en la página 2

CONTENTS 2.4 REFRIGERANT CYCLE ........................................... 10 1. PREFACE ................................................................ 2 2.4.1 CONDENSER .................................................. 10 1.1 FEATURES.................................................................. 2 2.4.2 EVAPORATOR ................................................. 10 1.2 SPECIFICATIONS ...................................................... 3 2.4.3 CAPILLARY TUBE ........................

Resumen del contenido incluido en la página 3

1.2 SPECIFICATIONS M6003R LWJ0611PCG MODELS M5403R M5203R M5203L WM-6011 LWC061JGMK1 ITEMS COOLING CAPACITY (BTU/h) 5,300 5,200 5,200 6,000 6,000 POWER SUPPLY (Phase, V, Hz) 1ø, 115V, 60HZ INPUT (W) 530 470 610 620 OPERATING CURRENT (AMP.) 4.8 4.3 5.6 5.8 REFRIGERANT CONTROL CAPILLARY TUBE REFRIGERANT CHARGE (R-22) 230g (8.1 Oz ) 330g(11.6 Oz) 335g (11.8 Oz) 235g (8.3 Oz) INSIDE FAN TURBO OUTSIDE FAN PROPELLER FAN WITH SLINGER RING AIR DISCHARGE 2-WAY (RIGHT AND LEFT) CHASSIS TOP-DOWN • OVE

Resumen del contenido incluido en la página 4

1.5 LOCATIONS OF CONTROLS 1.5.1 CONTROLS TEMPERATURE SETTING • This button can automatically control the temperature of the room. The temperature can be set within a range of 60°F(16°C) to 86°F(30°C) by 1°F(1°C). Select the lower number for lower temperature of the room. ENERGY SAVER The fan stops when the compressor stops cooling. • Approximately every 3 minutes the fan will turn on and check the room air to determine if cooling is needed. FAN/COOL/DRY • Everytime you push this button

Resumen del contenido incluido en la página 5

1.5.2 REMOTE CONTROLLER POWER • To turn the Set ON, push the button. To turn the Set OFF, push the button again. • This button takes priority over any other buttons. • When you first turn it on, the Set is on the High cool mode and the temp. at 72°F(22°C). TEMPERATURE SETTING • This button can automatically control the temperature of the room. The temperature can be set within a range of 60°F(16°C) to Power 86°F(30°C) by 1°F(1°C). Select the lower number for lower temperature of the room. FAN

Resumen del contenido incluido en la página 6

2. DISASSEMBLY INSTRUCTIONS 2.1 MECHANICAL PARTS 2.1.1 FRONT GRILLE Figure 1 1. Disconnect the unit from source of power. 2. Using a screwdriver, remove the screw that secures the front grille to control board. (See Figure 1) 3. Push the front grille up from the bottom. Pull the top of the front grille away from the cabinet as the top tabs lift out of their slots. (See Figure 2) 4. Replace the grille by placing the tabs in the slots and push the grille until it snaps into place. Figure 2 2.

Resumen del contenido incluido en la página 7

Figure 6 2.2 AIR HANDLING PARTS 2.2.1 AIR GUIDE UPPER 1. Disconnect the unit from the power source. 2. Remove the front grille. (Refer to Section 2.1.1) 3. Remove the cabinet. (Refer to Section 2.1.2) 4. Remove the control board. (Refer to Section 2.1.3) 5. Remove 2 screws that secure the air guide upper to air guide lower. (See Figure 6) 6. Lift air guide upper upward. 7. Re-install by referring to the procedures above. Figure 7 2.2.2 ORIFICE, TURBO FAN AND FAN 1. Disconnect the unit fro

Resumen del contenido incluido en la página 8

2.2.3 MOTOR Figure 10 1. Disconnect the unit from the power source. 2. Remove the front grille. (Refer to Section 2.1.1) 3. Remove the cabinet. (Refer to Section 2.1.2) 4. Remove the control board. (Refer to Section 2.1.3) 5. Remove the air guide upper. (Refer to Section 2.2.1) 6. Remove the compressor, turbo fan, fan and shroud. (Refer to Section 2.2.2) 7. Remove 2 screws that secure the motor to the motor. (See Figure 10) 8. Remove the motor. 9. Re-install by referring to the procedures ab

Resumen del contenido incluido en la página 9

2.3.2 COMPRESSOR Figure 14 1. Remove the front grille and cabinet. (Refer to Section 2.1.2) 2. Discharge the refrigerant by using a refrigerant recovery system. 3. Remove the overload protector. (Refer to Section 2.3.1) 4. After discharging the unit completely, unbrace the suction and discharge pipes at the compressor connections. 5. Remove 3 nuts which fasten the compressor. 6. Remove the compressor. 7. Re-install by referring to the removal procedure above. (See Figure 14) 2.3.3 CAPACITOR 1

Resumen del contenido incluido en la página 10

Figure 18 2.3.6 POWER CORD 1. Disconnect the unit from source of power. 2. Remove the front grille. (Refer to Section 2.1.1) 3. Remove the cabinet. (Refer to Section 2.1.2) 4. Remove 2 screws that secure control board to base pan and orifice. 5. Pulls the control board toward you. 6. Remove the grounding screw. 7. Remove a screw securing the clip with cord to the control board. 8. Pull the power cord. 9. Re-install by referring to procedures above. 2.4 REFRIGERANT CYCLE Figure19 2.4.1 CONDENSER

Resumen del contenido incluido en la página 11

6-4. Remove the hose from the vacuum pump and 2.4.3 CAPILLARY TUBE place it on the charging cylinder. See figure 1. Remove the cabinet. 23B. Open valve C. 2. Discharge the refrigerant by using a refrigerant Discharge the line at the manifold connection. recovery system. 6-5. The system is now ready for final charging. 3. Remove the air guide upper. (Refer to Section 7. Recharge as follows: 2.2.1) 7-1. Rotary compressor systems are charged from 4. After discharging the refrigerant completely,

Resumen del contenido incluido en la página 12

Equipment needed: Vacuum pump, charging cylinder, manifold gauge, brazing equipment, pinch-off tool capable of making a vapor proof seal, leak detector, tubing cutter, hand tools to remove components and service valve. COMPOUND GAUGE MANIFOLD GAUGE B A CONDENSER SEE INSETS (HIGH PRESSURE SIDE) BELOW COMPRESSOR EVAPORATOR (LOW PRESSURE SIDE) CAPILLARY TUBE LO HI CHARGING CYLINDER A A B B EXTERNAL VACUUM PUMP C Figure 20A-Pulling Vacuum Figure 20B-Charging —12—

Resumen del contenido incluido en la página 13

3. INSTALLATION This air conditioner is designed with a button-down chassis so it can be easily installed in a window. 3.1 SELECT THE BEST LOCATION 1. To prevent vibration and noise, make sure the unit is installed securely and firmly. 2. Install the unit where the sun does not shine directly INSIDE OUTSIDE on the unit. FENCE AWNING 3. The outside of the cabinet must extend outward for at least 10" and there should be no obstacles, such as a COOLED AIR fence or wall, within 20" from the back

Resumen del contenido incluido en la página 14

CENTER LINE ROOM SIDE Installation HARDWARE TYPE A: 11EA TYPE B: 4EA TYPE C: 3EA DRAIN PIPE (SHORT SCREW) (WOOD SCREW) (L BACKET) TYPE D: 1EA TYPE E: 1EA TYPE F: 2EA (SEAL STRIP) (SASH SEAL) (GUIDE PANEL) (Adhesive backed) (Not adhesive backed) 3.2.2 BEFORE INSTALLATION 1. Insert the guide panels into the guides of the air condi- tioner. Fasten the curtains to the unit with screws (TYPE TYPE A A) as shown Figure. 24. 2. Cut the adhesive-backed seal strip (TYPE D) to the window width. Remove the

Resumen del contenido incluido en la página 15

3. INSTALL THE AIR CONDITIONER IN THE WINDOW INNER SILL a. Carefully lift the air conditioner and slide it into the TYPE A OUTER SILL INSIDE open window. Make sure the bottom guide of the air CENTER LINE conditioner drops into the notches of the L bracket. See Figure. 27. 8" SHORT SIDE 8" OUTSIDE Figure 27 L BRACKET IMPORTANT : When the air conditioner drops into the L bracket, the air conditioner will be centered in window opening as shown in Figure. 28. b. While steadying the air conditioner,

Resumen del contenido incluido en la página 16

REMOVAL FROM WINDOW Turn the air conditioner off, disconnect the power cord, remove the L bracket and the screws installed through the top and bot- tom of the guide panels, and save for reinstallation later. Close the guide panels. Keeping a firm grip on the air conditioner, raise the sash, and carefully tilt the air conditioner backward, draining any condensate water. Lift the air conditioner from the window and remove the sash seal from between the windows. 3.3 ELECTRICAL DATA Line Cord Plug U

Resumen del contenido incluido en la página 17

4.2 PIPING SYSTEM CONDENSER COILS FAN MOTOR CAPILLARY TUBE TURBO FAN EVAPORATOR COILS Following is a brief description of the important components and their function in what is called the refrigeration system. Reference should be made to Figure 32 to follow the refrigerating cycle and the flow of the refrigerant in the cooling cycle. ROOM AIR CONDITIONER CYCLE OF REFRIGERATION EVAPORATOR COILS CONDENSER COILS VAPOR INLET SUCTION LINE HOT COMPLETE LIQUID COOL LOW PRESSURE VAPOR DISCHARGED BOIL

Resumen del contenido incluido en la página 18

4.3 TROUBLESHOOTING GUIDE In general, possible trouble is classified in two kinds. The one is called Starting Failure which is caused by an electrical defect. The other is Ineffective Air Con- ditioning caused by a defect in the refrigeration circuit and improper application. Unit is running but cooling is ineffective. Ineffective Cooling Check cold air Check outdoor coil Check heat load circulation for smooth (heat exchanger) and increase. flow. fan operation. Clean condenser. Dirty i

Resumen del contenido incluido en la página 19

Fails to Start Check of circuit breaker Check of power source. and fuse. Check of control panel Check control panel. setting. Compressor fails only to Fan only fails to start. start. Improper wiring. Improper thermistor Drop of power voltage. setting Defect of fan motor capacitor. Defect of compressor Loose terminal capacitor. connection Irregular motor resistance (Ω ) Capacitor check. Improper wiring Irregular motor insulation (Ω ) Replacement. Replacement of fan motor. I

Resumen del contenido incluido en la página 20

ELECTRIC PARTS TROUBLESHOOTING GUIDE: • The unit does not operate. Possible Trouble 1 NO • Check the Fuse. Is the Trans output power • Check the wiring diagram. AC 115V? YES NO NO • Check the Main Is the Trans output power Is shorted the Trans. output? P.W.B pattern. about AC 14V? YES YES • Exchange the Trans. • Exchange D02D~D05D. NO Is output Voltage of IC01D • Exchange IC01D. DC 12V? YES NO • Exchange IC02D. Is output Voltage of IC02D DC 5V? YES NO Is the reset circuit all right? • Exchan


Manuales de instrucciones similares
# Manual de instrucciones Categoría Descargar
1 Goldstar LS242CE Manual de instrucciones Aparato de aire acondicionado 275
2 Goldstar LT1230CR Manual de instrucciones Aparato de aire acondicionado 96
3 Goldstar M5403R Manual de instrucciones Aparato de aire acondicionado 32
4 Goldstar M5203L Manual de instrucciones Aparato de aire acondicionado 17
5 Goldstar M5203R Manual de instrucciones Aparato de aire acondicionado 25
6 Goldstar M6003R Manual de instrucciones Aparato de aire acondicionado 20
7 Goldstar WG5005R Manual de instrucciones Aparato de aire acondicionado 72
8 Goldstar WM-6011 Manual de instrucciones Aparato de aire acondicionado 15
9 Goldstar LWC061JGMK1 Manual de instrucciones Aparato de aire acondicionado 13
10 Sony SU-PW2 Manual de instrucciones Aparato de aire acondicionado 12
11 Sony CV-P12PX Manual de instrucciones Aparato de aire acondicionado 3
12 Sony MULTI CHANNEL AV RECEIVER STR-DG710 Manual de instrucciones Aparato de aire acondicionado 31
13 Sony VGN-BX500 Manual de instrucciones Aparato de aire acondicionado 1
14 Philips 190S5 Manual de instrucciones Aparato de aire acondicionado 21
15 Philips Comfort-Cire AMC 45 Manual de instrucciones Aparato de aire acondicionado 7