Resumen del contenido incluido en la página 1
TT-1650
Operating Instructions
INSIDE THE BOX:
(1) Aluminum Platter
(1) TT-1650 Turntable
(1) Counter Weight
(1) Headshell w/ (1) IEC Power Cable
Cartrdige
(1) RCA Cord w/
(1) Slipmat
Ground Wire
Resumen del contenido incluido en la página 2
Thank you for buying this Numark product. Please read these operating instructions so you will know how to operate this equipment properly. After you have finished reading these instructions, keep them for future reference. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with elec
Resumen del contenido incluido en la página 3
CAUTION! TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. IMPORTANT The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. NOTICE The exclamation point within an equilatera
Resumen del contenido incluido en la página 4
CONTROLS General Controls 1. Power Button Pushing this button down turns on the turntable. 2. Start/Stop Buttons These buttons start and stop the turntable motor. Both buttons have the same function. 3. Platter This turntable has a special edge design that has been optimized for "dragged" platter slow downs. 4. Pitch Slider This slide control allows the pitch to be increased or decreased by 10%. In the center position the pitch is at 0%. When moved away from the center and towards the tone arm
Resumen del contenido incluido en la página 5
CONTROLS continued Tone Arm Parts 7 7. Counter Weight and Scale Ring The Counterweight is used to balance the head shell and cartridge assembly so that the proper amount of stylus pressure is applied to the record. 8. Anti-Skate Adjustment 8 This knob is used to compensate for inward tracking forces. See Tonearm Setup for more details. 9. Tonearm Cue System 9 This cueing system allows the tone arm to be positioned at a certain point above the record and slowly engaged. When 10 the lift leve
Resumen del contenido incluido en la página 6
SETUP & INSTALLATION This turntable has been designed exclusively for DJ use and can be setup in a variety of different ways depending on your mixing style. The turntable should rest on a level and stable surface that is clear of obstructions. If a mixer is placed between two turntables make sure that there is at least ¼" (7mm) between the mixer and the turntables to prevent damage to the turntables and to reduce unwanted system noise. Mixer Mixer 85 mm ¼" ¼" Setup Style 1 (traditional) Best
Resumen del contenido incluido en la página 7
PLATTER SETUP WARNING: Incorrect Platter setup can lead to poor turntable performance, platter instability or permanent motor damage. 1. Start by inspecting the bottom of the aluminum platter to check that both locking pins have rubber fittings on them. 2. Next, rotate the top of the motor assembly (brass in color) so that two holes are aligned parallel with the front of the turntable. 3. Install the platter onto the center spindle and motor assembly making sure that the Numark logo and
Resumen del contenido incluido en la página 8
CABLE SETUP This turntable is shipped with two sets of special cables: (1) Right Angle IEC Power Cord (1) Right Angle RCA cord w/ground wire NOTE: Before connecting any cables, make sure that the voltage selector switch is set to the proper setting, either 110V or 220V depending on region. Making the power and audio connections: 1. Begin by lifting the turntable up from the rear handle and resting it on its side. (NOTE: The turntable must be supported because it is not stable in this positio
Resumen del contenido incluido en la página 9
2.5 1.5 1.5 2 1 1 1.5 0.5 0.5 TONE ARM SETUP A properly adjusted tone arm and cartridge setup will minimize vinyl record wear and optimize the performance of the turntable. Follow these simple steps for setting the tone arm on the turntable: Balancing the Tone Arm 1. Begin the balancing process by lifting the cue lever to the up position (or make sure that the stylus protector is on the cartridge.) 2. Next, rotate the counterweight clockwise until it is in the complete forward position (NOTE
Resumen del contenido incluido en la página 10
CARTRIDGE SETUP For Head Shell Mounted Cartridges: The cartridge that comes with this turntable should be preinstalled on the head shell. If it isn't, please follow the below instructions for installing a cartridge onto the head shell. 1. Position the head shell and the cartridge so that the four connector pins are visible. Make sure that the stylus cover is installed to prevent damage to the stylus during installation. 2. Prepare to connect the cartridge to the head shell using the green, r
Resumen del contenido incluido en la página 11
OPERATION This turntable was designed to accommodate a variety of different mixing styles. Here are some general operation guidelines to optimize the performance of the turntable. 1. Do not place the turntable on or near a speaker or subwoofer. This may cause unwanted noise depending on the environment conditions. 2. ALWAYS use the included Slip Mat during record playback. This Slip Mat was designed to reduce friction between the platter and the record to allow for rapid back cueing and e
Resumen del contenido incluido en la página 12
LIMITED PRODUCT WARRANTY 1. What is covered and for how long? NUMARK INDUSTRIES LCC ("NUMARK") warrants to the original purchaser that NUMARK'S products; including but not limited to DJ mixers, amplifiers, CD players, CD Mix Stations, turntables, preamplifiers, beatkeepers, equalizers, microphones, headphones, cartridges, and all other accessories; are to be free from defects in material and workmanship under normal use and service for the period commencing upon the date of purchase from an
Resumen del contenido incluido en la página 13
RETURN INFORMATION (US ONLY) a) A Return Authorization number must be obtained from Numark through the address or phone numbers below. b) A copy of the original sales receipt must also be included for the equipment to be repaired under warranty. c) The faulty equipment must be packed in its original packaging. d) One additional outer layer of packaging must be included to ensure product safety. Failure to do so may inadequately protect the equipment in transit and, therefore, jeopardize the cus
Resumen del contenido incluido en la página 14
SPECIFICATIONS Turntable Section: Type: 2 speed, fully manual Motor: Direct Drive Starting Torque: > 1 Kg/cfm Platter: Aluminum Diecast Speed: 33.333 and 45 RPM Wow & Flutter: < 0.25% WRM S/N ratio: > 50dB Pitch Range: +/-10% Tonearm Section: Type: Universal S-Shaped Aluminum Height Range: Fixed Cue System: Lift Lever, Arm Rest and and Arm Clip Weight Type: 85 Gram Plated Brass w/ 0-3.5 gram range scale General: Dimensions: 370mm(W) by 460mm(D) by 135mm(H) Weight: 5.36 Kg PAGE 1
Resumen del contenido incluido en la página 15
Problem Cause? Solution Turntable does not turn on. Disconnected Power Cord? Connect Power Cord. The sound level is very low. The Turntable is not connected to a Connect the device to a preamp DJ device with a PHONO preamp. mixer or an AV receiver that has an input labeled PHONO, not AUX or LINE. The sound is on one side only. The Cartridge is not properly wired. Reconnect the wires from the headshell to the cartridge. See the "Cartridge Setup" section for more detail. The Stylus is worn o
Resumen del contenido incluido en la página 16
TT-1600, TT-1650 Manual /English - rev B Copyright Numark Industries, LLC 2002
